GBC Velobind V800 Pro Bruksanvisning

GBC Inte kategoriserad Velobind V800 Pro

Läs nedan 📖 manual på svenska för GBC Velobind V800 Pro (6 sidor) i kategorin Inte kategoriserad. Denna guide var användbar för 2 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF
Sida 1/6
1.0 INTRODUCTION
1.1 OPERATIONAL COMPONENTS LAYOUT
Figure 1-1
1-2
Pressure Bar
Handle
Housing
Base
Waste Tray
Punch Guide
Light
Bind Guide
Locating Pin
Backstop
Strip Recess
2.0 SPECIFICATIONS
DESCRIPTION: Punch/Binder
PUNCH CAPACITY:* 1/8 in. (3.2 mm) X 14 in. (355.6 mm)
25 sheets of 20 lb. bond paper
*Note: No more than 4 composition covers, or
3 plastic covers should be punched at one time.
Punching stacks of these materials may result
in damage to the punch mechanism.
BIND CAPACITY: 1 in. (25 mm) X 14 in. (355.6 mm)
250 pages of 20 lb. bond paper
ELECTRICAL REQUIREMENTS: 120 VAC 230 VAC 100 VAC
60 Hertz 50 Hertz 50 Hertz
3 Amps 1.5 Amps 1.5 Amps
409.56 B.T.U.'s per hour
3-wire grounded outlet
CYCLE SPEED: 2 second punch cycle
8-10 second bind cycle
DIMENSIONS: 20 in. (50.8 cm) wide
7 in. (17.8 cm) high
15 in. (38.1 cm) deep
WEIGHT: 28 lbs. (12.7 kg)
2-1
3.0 INSTALLATION PROCEDURE
3.1 Unpacking Instructions
To unpack the machine, carefully remove the staples and open the carton. Remove
the packing material from the top and around the machine, and lift the machine
straight up out of the carton. Place the machine on a table near a 120 VAC or 220-
240 VAC grounded outlet, and remove the plastic bag.
3.2 Power Cord Configuration
This machine is supplied with a power cord terminating in a conventional three
prong electrical plug. Under no circumstances should the grounding prong of the
power cord be removed to facilitate connection to a non-approved outlet.
3.3 Checking Machine Operation
The handle should operate with relative ease. Leave it in the "up" or starting
position after testing several times.
With the handle in the starting position, check the pressure bar to ensure it can
be easily lowered and raised by the operator. Leave it in the "up" position after
testing several times.
The machine is now ready to operate. Instruct operator in proper punching and
binding procedures. Point out the operating instructions found in the waste tray,
and leave the owner's guide for the customer. Be sure to stress the importance of
the document being properly placed on the locating pin for binding.
3-1

Produktspecifikationer

Varumärke: GBC
Kategori: Inte kategoriserad
Modell: Velobind V800 Pro

Behöver du hjälp?

Om du behöver hjälp med GBC Velobind V800 Pro ställ en fråga nedan och andra användare kommer att svara dig


Inte kategoriserad GBC Manualer

GBC

GBC ThermaBind T500Pro Bruksanvisning

19 Oktober 2024
GBC

GBC Velobind V800 Pro Bruksanvisning

14 September 2024

Inte kategoriserad Manualer

Nyaste Inte kategoriserad Manualer

Philips

Philips 43PUL7672 Bruksanvisning

27 Oktober 2024
Manhattan

Manhattan 461504 Bruksanvisning

27 Oktober 2024
Sungrow

Sungrow SG125HV Bruksanvisning

27 Oktober 2024
Schneider

Schneider CCT724319 Bruksanvisning

27 Oktober 2024
Technoline

Technoline WS 250 Bruksanvisning

27 Oktober 2024
Livarno

Livarno IAN 354423 Bruksanvisning

27 Oktober 2024
Kupper

Kupper 12152 Bruksanvisning

27 Oktober 2024
JennAir

JennAir CARBON24L Bruksanvisning

27 Oktober 2024
Medion

Medion Life E74001 (MD 81035) Bruksanvisning

27 Oktober 2024
POLARIS

POLARIS Sportsman Touring 850 SP (2015) Bruksanvisning

27 Oktober 2024