GE GXITD Bruksanvisning

GE Inte kategoriserad GXITD

Läs nedan 📖 manual på svenska för GE GXITD (6 sidor) i kategorin Inte kategoriserad. Denna guide var användbar för 3 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF
Sida 1/6
Service Service Max. Average Average
Model Flow rate Life Pressure Temp. Contaminant % Reduction Influent Effluent
GXITD
0.5 gpm 2000 gal. (7571 liters) 25–125 psi 100°F. Chlorine 93% 2.0 mg/L 0.1 mg/L:
(1.9 lpm) or 6 months (172–862 kPa) (38°C.)
GE SmartWater™
GE Model GXITD Filter
Do not use with water that is microbiologically
unsafe or with water
of unknown quality without adequate disinfection before or after
the system.
Small parts remaining after the installation could be a choke
hazard. Discard safely.
System Tested and Certified by NSF International against
ANSI/NSF Standard 42 for
the reduction of Taste and Odor,
and Chlorine, Class I.
WARNING
INSTALLATION PRECAUTIONS
•Protect from freezing. Drain filter when room temperature drops below 32°F. (0°C.).
•Use the in-line water filtering system on a potable, safe-to-drink, home COLD water supply only.
The filter will not make unsafe water safe to drink. Do NOT use on HOT water (100°F. max.).
•Do not install on line pressure above 125 psi (862 kPa), or below 25 psi (172 kPa).
•All of the refrigerator installation requirements must be met when installing the filter.
•Do not use wicking or pipe dope sealer for fitting connections into head of filter. Teflon® tape is recommended and included.
Teflon is a registered trademark of DuPont.
•Do not install in direct sunlight.
•Installation must comply with existing state or local plumbing codes.
•It is essential that operational, maintenance and filter replacement requirements be carried out for this product to perform as advertised.
Change filter at least every six months. Flush new cartridge for 5 minutes.
REQUIRED TOOLS FOR INSTALLATION
•a tube cutter
• 7/16 1/2 and 9/16 wrenches″, ″ ″
• a knife
• a bucket or pan
OPTIONAL TOOLS FOR INSTALLATION
•a file
•sandpaper
CAUTION: Using pliers or vise grips damage the fittings.WILL
Your new GE icemaker water filter comes complete with all the necessary hardware for installation. Each filter gives you up to six
months of great-tasting water. Filter should be changed after 6 months of use.
SPECIFICATIONS
Testing parameters: Influent Challenges = pH 7.5 ± 0.5; Temperature 68°F ± 5°F (20°C ± 3°C); Pressure 60 psig; Flow Rate = 1gpm
If slow water or hollow ice occurs, replace filter.
Part No. 251B6017P003 Pub. No. 49-50047(10-99 JR)
For service, parts, or maintenance call: GE Answer Center® 800.626.2000
GENERAL ELECTRIC COMPANY, Appliance Park, Louisville, KY 40225
LIMITED 60 DAY WARRANTY
•What does this warranty cover?
— Any defect in materials or workmanship in the manufactured product.
•What does this warranty not cover?
— Customer installation. The Installation Instructions cover installation and
replacement instructions.
— Defects that result from abuse, misuse, alterations, improper installation or
damage not caused by GE.
— Liability on the part of GE under this or any other warranty for any indirect or
consequential damage.
— Products that are used for commercial or industrial applications.
•For how long after the original purchase?
— Sixty (60) days.
•How do I make a warranty claim?
— Return to the retailer from which it was purchased along with a copy of the “Proof
of Purchase.”
•How does state law relate to this warranty?
— This warranty gives you specific legal rights, and you may also have other rights
which vary from state to state.
Attach Fittings to Filter
2. a. Remove yellow endcaps from filter.
b. Find the ends of brass fittings that mate with
filter body.
c. Apply 1 to 2 wraps of the included Teflon
tape to threads, as shown.
d.Thread brass fittings into both ends of the
filter body and tighten snug with a wrench.
Cut Tubing
3. Shut off water supply.
4.
The filter is to be inserted (spliced) into the
1/4
″
OD supply tube that feeds water to the
refrigerator. (Do not cut any water lines
internal to the refrigerator.) Locate the filter
as close as possible to the supply water shut-off
valve. If the filter needs to be located behind
the refrigerator, there needs to be at least 6
inches of clearance between the wall and the
refrigerator. If the appliance must be moved,
make sure there is proper protection on
the floor.
5. Cut the tubing, making sure the ends are
square and no burrs protrude. Deburr ends
with file or sandpaper if necessary.
Attach Fittings to Tubing
6. Slip brass nuts then ferrules over both tubing
ends, leaving 1/4 of tubing exposed from″
end.
(See figure for ferrule orientation).
For copper tubing, use the brass ferrules.
For plastic tubing, use plastic ferrules and
brass inserts.
7. Connect the supply water line to the filter
inlet:
a. Insert end of tubing into brass fitting; hand-
tighten nut onto threads of brass fitting.
b. Using two wrenches, tighten nut at least one
full turn.
CAUTION: Be careful not to cross thread the nut
and the fitting.
See step 8 below to complete the installation.
Teflon
tape
Brass nut Brass nut
Brass insert
(for plastic tubing)
Brass insert
(for plastic tubing)
Water line
tubing Water line
tubing
Ferrule FerruleBrass
fitting
Brass
fitting
SUPPLY SIDE INLET OUTLET APPLIANCE SIDE
Follow Directions for Proper Assembly
Flush Filter
8. Place filter outlet over bucket or pan. Turn on the incoming water
supply to
flush
the filter into
the bucket or pan thereby removing fine
particles of carbon which may be present. Flush 2 to 3 gallons of water
(approx. 5 minutes). Turn off the water supply.
Final Connection and Leak Check
9. Connect the
outlet
port of the filter to the water line to your appliance
in the same manner as the inlet.
10. Turn on water supply line. If leak occurs, tighten nuts or fittings until
leak stops.
11. Write the date on the filter and also mark your calendar to replace
with another filter after six months.
12. Discard any unused parts.
OPTION 1:
Brass Fittings
Attach Fittings to Filter
2. a. Remove yellow endcaps from filter.
b. Apply 1 to 2 wraps of the included Teflon
tape to threads of o-ring fittings, as shown.
c. Thread o-ring fittings into both ends of the
filter body and tighten snug with a wrench.
Leave at least one turn of thread showing.
Cut Tubing
3. Shut off water supply.
4. The filter is to be inserted (spliced) into the
1/4 OD supply tube that feeds water to the″
refrigerator. (Do not cut any water lines
internal to the refrigerator.) Locate the filter
as close as possible to the supply water shut-
off valve. If the filter needs to be located
behind the refrigerator, there needs to be at
least 6 inches of clearance. If the appliance
must be moved, make sure there is proper
protection on the floor.
5. Cut the tubing, making sure the ends are
square and no burrs protrude. Deburr ends
with file or sandpaper if necessary.
Attach Fittings to Tubing
6. Slip brass
nuts then ferrules over both tubing
ends, leaving 1/4 of tubing exposed from″
end. (See figure for ferrule orientation). For
both copper and plastic tubing, use plastic
ferrules. If your tubing is plastic, place brass
inserts into ends of tubing.
7. a. Insert end of supply side tubing into the
valved fitting (the
longer
fitting);
hand-
tighten nut onto threads of fitting.
CAUTION: Be careful not to cross thread
the nut and the fitting.
b. Using two wrenches, tighten nut at least
one full turn.
c. Valved fitting is now installed. Turn water
supply on and inspect for leaks.
d. Repeat a band for non-valved fitting on
the appliance side.
See step 8 below to complete the installation.
Teflon
tape
Brass nut Brass nut
Brass insert (for
plastic tubing) Brass insert (for
plastic tubing)
Water line
tubing
Water line
tubing
Ferrule FerruleValved fitting Non-valved
fitting
O-ring
fitting
O-ring
fitting
SUPPLY SIDE INLET OUTLET APPLIANCE SIDE
Follow Directions for Proper Assembly
OPTION 2:
Quick Connect
Installation Kit
QCKIT
(sold separately)
1. All of the
refrigerator
installation
requirements
must be met
when installing
the filter.
1. All of the refrigerator
installation
requirements must
be met when
installing the filter.
INSTALLING THE FILTER
Two installation methods are available: • Option 1 (brass fittings) • Option 2 (quick-connect fittings)
GE SmartWater
™
Filtre GE Modèle GXITD
Ne pas utiliser ce produit sans une désinfection adéquate avant
ou après le système, avec du l’eau de qualité inconnue ou
microbiologiquement polluée.
Les petites pièces non utilisées après l’installation peuvent
susciter un risque d’étouffement pour les jeunes enfants.
Veiller à les éliminer.
Système testé et homologué par NSF International, selon la
norme ANSI/NSF No42 pour la réduction de la concentration
de chlore et la suppression des goûts et odeurs, Classe I.
AVERTISSEMENT
INSTALLATION PRECAUTIONS À OBSERVER
• Protéger le produit contre le gel. Vider le filtre lorsque la température de la pièce pourrait s’abaisser au-dessous de 32°F (0°C).
• Utiliser le système de filtration en série uniquement sur une canalisation d’eau potable FROIDE. Le filtre ne rendra pas potable pour la
consommation une eau de qualité déficiente. Ne PAS installer le produit sur une canalisation d’eau CHAUDE (100°F max.).
• Ne pas installer le produit sur une canalisation dont la pression est supérieure à 125 lb/po2 (862 kPa), or inférieure à 25 lb/po2 (172 kPa).
• Lors de l’installation du filtre, on doit respecter toutes les exigences concernant l’installation du réfrigérateur.
• N’utiliser aucun produit d’étanchéité ordinaire au niveau des raccordements sur la tête du filtre. Utiliser uniquement du ruban de Teflon®
(inclus)–Teflon est une marque de commerce déposée de DuPont.
• Ne pas installer le produit à un emplacement exposé au rayonnement solaire direct.
• L’installation doit satisfaire les prescriptions des codes locaux de plomberie.
• Pour que la performance de ce produit soit conforme à ce qui est annoncé dans les publicités, il est essentiel que les opération d’entretien et
remplacement de l’élément fitlrant soient exécutées conformément aux spécifications. Changer l’élément filtrant à intervalles de six mois.
Rincer la cartouche neuve pendant 5 minutes.
OUTILLAGE NÉCESSAIRE POUR L’INSTALLATION
•coupe-tube
• clés de 7/16 po, 1/2 po et 9/16 po
• couteau
• seau ou récipient
MISE EN GARDE: Ne pas utiliser une pince ou pince-étau sur les
raccords–ils subiraient des dommages.
OUTILLAGE FACULTATIF POUR L’INSTALLATION
•lime
•papier abrasif
•tournevis
•perceuse et foret
Votre nouveau filtre à eau GE pour générateur de glaçons est fourni avec toutes les pièces nécessaires pour l’installation. Chaque filtre permet
la production d’une eau d’excellente qualité pendant près de six mois. On devrait changer le filtre après 6 mois d’utilisation.
SPECIFICATIONS
Paramètres de test: Caractéristiques de l’eau à traiter = pH 7,5 ± 0,5; température 68°F ± 5°F (20°C ± 3°C); pression 60lb/po
2
relative; débit= 1gpm
Remplacer le filtre si le débit est insuffisant ou si les glaçons sont creux.
Pièce No251B6017P003 (10-99 JR) Pub. No49-50047
Pour réparations, pièces ou entretien, téléphoner à
: Centre de réponse GE® : 800.626.2000
GENERAL ELECTRIC COMPANY, Appliance Park, Louisville, KY 40225
GARANTIE LIMITÉE DE 60 JOURS
•
Que couvre la garantie?
— Tout vice de matériau ou de fabrication du produit fabriqué.
•
Situations non couvertes par la garantie?
— Installation par le client. Les instructions d’installation couvrent installation et
remplacement du filtre.
— Défauts imputables à utilisation impropre ou abusive, modification, installation
incorrecte ou dommages non imputables à GE.
— Obligation qui serait imposée à GE au titre de dommages indirects ou secondaires en
vertu de toute garantie.
— Produits utilisés dans une application commerciale ou industrielle.
•
Durée de la garantie après la date d’achat?
— Soixante (60) jours.
•
Comment soumettre une demande au titre de la garantie?
— Retourner le produit au détaillant chez qui il a été acheté, accompagné d’une copie
du document de « preuve d’achat ».
•
Relation entre cette garantie et la législation provinciale?
— Cette garantie vous confère les droits juridiques spécifiques; vous pouvez également
jouir d’autres droits, variables d’une province à une autre.
Débit en Capacité/ Temp. Taux de Eau brute Effluent
Modèle service longévité Pression max. Contaminant reduction % valeur moy. valeur moy.
GXITD
0,5 gpm 2000 gal. (7571 litres) 25–125 psi 100°F. Chlore 93% 2,0 mg/L 0,1 mg/L:
(1,9 lpm) ou 6 mois (172–862 kPa) (38°C.)

Produktspecifikationer

Varumärke: GE
Kategori: Inte kategoriserad
Modell: GXITD

Behöver du hjälp?

Om du behöver hjälp med GE GXITD ställ en fråga nedan och andra användare kommer att svara dig


Inte kategoriserad GE Manualer

GE

GE Profile PS96PZRSS Bruksanvisning

13 Oktober 2024
GE

GE ZXR7510C Bruksanvisning

6 Oktober 2024
GE

GE ZCGS150LSS Bruksanvisning

18 September 2024
GE

GE Profile UCG1600LWW Bruksanvisning

16 September 2024
GE

GE GXITD Bruksanvisning

16 September 2024
GE

GE ZCG3100VBB Bruksanvisning

23 Augusti 2024
GE

GE GXILQR Bruksanvisning

22 Augusti 2024
GE

GE ZX12B48WSS Bruksanvisning

21 Augusti 2024
GE

GE Profile GXCF35GBS Bruksanvisning

21 Augusti 2024
GE

GE ZX1B36WSS Bruksanvisning

16 Augusti 2024

Inte kategoriserad Manualer

Nyaste Inte kategoriserad Manualer

Philips

Philips 43PUL7672 Bruksanvisning

27 Oktober 2024
Manhattan

Manhattan 461504 Bruksanvisning

27 Oktober 2024
Sungrow

Sungrow SG125HV Bruksanvisning

27 Oktober 2024
Schneider

Schneider CCT724319 Bruksanvisning

27 Oktober 2024
Technoline

Technoline WS 250 Bruksanvisning

27 Oktober 2024
Livarno

Livarno IAN 354423 Bruksanvisning

27 Oktober 2024
Kupper

Kupper 12152 Bruksanvisning

27 Oktober 2024
JennAir

JennAir CARBON24L Bruksanvisning

27 Oktober 2024
Medion

Medion Life E74001 (MD 81035) Bruksanvisning

27 Oktober 2024
POLARIS

POLARIS Sportsman Touring 850 SP (2015) Bruksanvisning

27 Oktober 2024