HOLGA 135-3D Bruksanvisning

HOLGA Kamera 135-3D

Läs nedan 📖 manual på svenska för HOLGA 135-3D (10 sidor) i kategorin Kamera. Denna guide var användbar för 2 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF

Sida 1/10

HOLGA 135-3D

3-DIMENSIONAL PICTURE CAMERA

OPERATION INSTRUCTIONS

Welcome to owning this special, one of a kind, 3D camera!

By making resemblance to the same principle in the capture of images by the human eyes, the two

built-in lenses of the Holga 135-3D cameras will simultaneously capture two almost identical and yet

different pictures which, through the use of specially designed viewing devices (optionally

available separately), will enable the reproduction of the captured image in 3-dimensonal

photographic effects which approximate reality.

In addition, you can still take separate conventional 2D pictures one at a time with this camera.

With this 3D camera, you will cross the threshold to enter a total new world of fun and joy in taking

pictures.

Enjoy!

1. Parts of the Camera

Fig. 1 Fig. 2

(1) B-Mode Selector 1 (12)

Socket for Shutter Release Cable

(2) Focus Ring 1 (13)

Hot Shoe

(3) Lens 1 (14)

View Finder

(4) Aperture Selector 1 (15)

Film Rewind Knob

(5) Lens Cap 2 (16

)

Film Rewind Handle

(6) Focus Ring 2 (17)

Back Cover

(7) B-Mode Selector 2 (18)

View Finder Eyepiece

(8) Aperture Selector 2 (19)

Film Advance Gear

(9) Ring for Hand Strap (20)

Film Release Button

(10) Film Counter (21)

Tripod Mounting Socket

(11) Shutter Release Button

2. Film to Use

The camera can accommodate all 135 format films. The use of films with exposure speed

ASA 100 on sunny days and ASA 400 on cloudy days /indoor occasions is recommended.

3. Film Loading

Film Compartment Film Advance Sprockets Film Tongue “1”

Slot on Take-Up Spool

Fig. 3 Fig. 4 Fig. 5

(a) Grab the Film Rewind Handle to pull up the Film Rewind Knob. - the latch for the

Back Cover will be released and the Back Cover will pop open. (Fig. 3)

(b) Insert a new film roll into the Film Compartment and push the Film Rewind Knob back

to engage into the film roll. If the knob cannot be pushed back, turn it slowly until it

can be done so.

approximately, but not beyond, the hinge for the Back Cover.

(d) Insert the tip of the Film Tongue into the slot on the Take-Up Spool. Press the film

so that the tip of the film goes into the Take-Up Spool and the film becomes more or

less flat. (Fig. 4)

(e) Turn the Film Advance Gear slightly while adjusting the Film Advance Sprockets at

the same time to enable the sprockets to engage into the holes on the two sides of the

film.

(f) Snap the Back Cover back into place.

(g) Turn the Film Advance Knob to advance the film until it cannot turn any further and

then press the Shutter Release Button.

(h) Repeat (g) again until the number “1” appears in the Frame Counter (Fig. 5). The

camera is now ready for taking pictures.

4. Focusing

Although this camera is basically a fixed focus camera, it still offers four choices of object

distances. There are four symbols on the Focus Ring to make selection for the following

object distances -

(a)

= 1m or 3.25 ft.

(b)

= 2m or 6.50 ft.

(c)

= 6m or 20.00 ft

(d)

= 10m or 33.00 ft. or more

More precise setting for object distances can be achieved by turning the Focus Ring to

positions in between two symbols.

Focus Ring

Aperture Selector

Fig. 6

5. Choice of Aperture

By setting the Aperture Selector (Fig. 6 above), two choices are available for selection as

follows -

(a) Sunny Symbol = f/11 for use on sunny days; and

(b) Cloudy Symbol

= f/8 for use on cloudy days.

6. Picture Taking

6.1. Taking 3D Pictures

(a) Remove the covers of both lenses.

(b) Set BOTH B-Mode Selectors 1 & 2 to the “N” position.

conditions :-

- Sunny symbol for sunny outdoor occasions; and

- Flash/Cloudy symbol for cloudy outdoor or insufficiently lit-up indoor

occasions.

(d) Estimate the object distance and turn BOTH Focus Rings 1 & 2 to set the object

distance accordingly.

Produktspecifikationer

Varumärke:	HOLGA
Kategori:	Kamera
Modell:	135-3D
Husmaterial:	Kunststof
Typ av seriell anslutning:	RS-232/422/485
Antal Ethernet LAN (RJ-45)-portar:	2
Certifiering:	CE, FCC, UL/cUL
Inspänning:	12 - 48 V
Ethernet LAN, dataöverföringshastigheter:	10, 100 Mbit/s
Typ av enhet:	Gateway voor mobiele netwerken
Förvaringstemperatur:	-40 - 85 °C
Datanätverk:	Niet ondersteund
Kompatibla operativsystem:	Windows 98/ME/NT/2000\nWindows XP/2003/Vista/2008/7 x86/x64
Elektromagnetisk kompabilitet:	EN61000-4-2 (ESD) lvl 3, EN61000-4-3 (RS) lvl 3, EN61000-4-4 (EFT) lvl 4, EN61000-4-5 (Surge) lvl 3, EN61000-4-6 (CS) lvl 3, EN61000-4-8, EN61000-4-11, EN61000-4-12
Säkerhet:	UL (UL60950-1), TÜV (EN60950-1)
Medeltid mellan fel (MTBF):	210794 uur
Auto MDI/MDI-X:	Ja
Mått (B x D x H):	29 x 89.2 x 124.5 mm
Seriell port(ar):	1
Drifttemperatur (TT):	0 - 55 °C
Relativ luftfuktighet i drift (VV):	5 - 95 procent
Isolering:	2 kV
Skydd mot elektrostatisk urladdning (ESD).:	15 kV
Baud hastighet:	0.050 Kbit/s
RS-422-signaler:	RxD+, RxD-, SGND, TxD+, TxD-
RS-485-signaler:	Data+, Data-, RxD+, RxD-, SGND, TxD+, TxD-
Databitar:	7, 8
RS-232-signaler:	CTS, DCD, DSR, DTR, GND, RTS, Rx, Tx