Horizon Fitness Avalon 100 Bruksanvisning

Läs nedan 📖 manual på svenska för Horizon Fitness Avalon 100 (1 sidor) i kategorin Cykeltränare. Denna guide var användbar för 6 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Sida 1/1
TENSION
KNOB
TENSION
KNOB CABLE
SEAT BACK
HANDLEBARS
SEAT BOTTOM
CONSOLE
CONSOLE DATA
CABLE
SEAT FRAME
SEAT LEVER
REAR FOOT PAD
PEDAL
C
E
D
D
MOBILE
WHEEL
SLEEVE
A
B
C
C
REAR FOOT TUBE
G
F
H
I
E
MOBILE
WHEEL
U N P A C K I N G
Unpack your Exercise Bike where you will be
using it. Place your bike on a level flat surface. It
is recommended that you place a protective cov-
ering on your floor. You will only need to attach
the following items. Verify that the following parts
and tools are included:
Parts
1 Rear Foot Tube
1 Handlebar Set
1 Seat Rail
1 Seat Back
1 Seat Bottom
1 Seat Frame
1 Console Mast
1 Console Mast Boot
2 Mobile Wheels
1 Console
2 AA Batteries
2 Pedals
2 Wheel Sleeves
1 Tension Knob
1 Seat Rail Boot
1 Hardware Pack (contents listed below)
D) Washer
Quantity: 8
F) 14mm Washer
Quantity: 2
G) 20mm Bolt
Quantity: 2
A) 12mm screw
Quantity: 2
B) 20mm Bolt
Quantity: 2
C) 15mm Bolt
Quantity: 10
E) 40mm Bolt
Quantity: 8
Tools (included)
5mm Allen Wrench/
Phillips Screw Driver
Flat Wrench
NOTE: It is recommended that you apply
grease to the threads of each bolt as you assem-
ble your Exercise Bike, to prevent loosening and
noise. Also, during each assembly step, ensure
that ALL nuts and bolts are in place and partially
threaded in before completely tightening any
ONE bolt.
STEP 9
Connecting the Tension Knob
a. Remove the 20mm long bolt (I)
on the back of the tension knob.
b. Turn the tension knob to level 15.
Connect the tension knob to the
bottom of the tension knob cable
(Figure A, Step 2).
c. Grasp the tension knob and firmly
pull the tension knob assembly
away from the machine in order to
attach to the top of the tension knob
cable (Figure B, Step 3). Make sure
that the copper cable end is seated
properly into the "key hole".
d. Insert the tension knob into the rec-
tangular opening on the console
mast (Figure C, Step 5).
e. Secure the tension knob with the
20mm bolt (I) by using a screw
driver (Figure D, Step 6).
STEP 1
Attach the Foot Wheels
a. Insert the wheel sleeves on each
side of the front wheel tube.
b. Align the holes in the wheel sleeves
with the holes in the wheel tube.
Insert two 12mm screws (A) and
secure with a screwdriver.
c. Attach the mobile wheels to the
wheel sleeves. Insert two 14mm
washers (F) and two 20mm bolts
(G) and secure with a screwdriver.
STEP 2
Attach the Rear Foot Tube
a. Align the holes of the rear foot
tube with the holes on the seat
rail.
b. Insert two 20mm bolts (B) and
secure with a 5mm allen wrench.
STEP 8
Attach the Pedals
a. Thread the right pedal into the right
side pedal crank arm. Note: The
pedals are labeled on the end of the
threaded shaft for reference.
b. Tighten the pedal with the flat
wrench.
c. Repeat this process on the left side.
STEP 3
Attaching the Handlebars
a. Attach the handlebars to the seat
frame using two 15mm bolts (C).
Secure with a 5mm allen wrench.
STEP 7
Attaching the Console
a. Open the battery cover on the
back of the console, insert two AA
batteries into the console and
replace the battery cover.
b. Connect the cable from the console
to the console cable running
through the console mast, making
sure that both ends snap together
tight.
c. Attach the console to the console
mast plate with the 15mm screws
(H). Secure using a screwdriver.
Note: Screws (H) are located on the
back side of the console.
STEP 6
Attaching the Console Mast
a. Slide the console mast boot onto
the console mast.
b. Slide the tension knob cable along
with the console cable into the
console mast.
c. Holding the console mast above
the top console mast bracket,
guide both cables through the
console mast while simultaneously
sliding the console mast onto the
console mast bracket. Continue to
guide the console cable through
the top of the console mast.
d. Insert four 15mm bolts (C) and
secure with a 5mm allen wrench.
e. Slide the console mast boot down
to cover the bolt heads.
STEP 4
Attach the Seat Back and Bottom
a. Align the holes in the seat frame
with the holes in the seat bottom.
b. Insert four washers (D) and four
40mm bolts (E) and secure with a
5mm allen wrench.
c. Align the holes in the seat frame
with the holes in the seat back.
d. Insert four washers (D) and four
40mm bolts (E) and secure with a
5mm allen wrench.
STEP 5
Attach the Seat Rail and Frame
a. Slide the seat frame onto the seat
rail. Slide the seat rail boot onto
the seat rail.
b. Slide the seat rail onto the main
frame bracket until the holes on
the seat rail and main frame
bracket are aligned.
c. Insert four 15mm bolts (C) and
secure with a 5mm allen wrench.
Figure A
Figure B
Figure C
Figure D
6
5
4
3
2
1
CONSOLE
MAST
H a r d w a r e (Actual Size)
C U S T O M E R A S S I S T A N C E C E N T E R 1 . 8 8 8 . 9 9 3 . 3 1 9 9 o r w w w . h o r i z o n f i t n e s s . c o m
GRIP PULSE
CONSOLE
MAST
BOOT
SEAT RAIL
BOOT
Avalon
1
1
1
11
1
1
1
1
10
0
0
00
0
0
0
0
00
0
0
00
0
0
0
0
0
D
C
B
C
avalon 100 assemblyguidev1.0.qxd 3/12/2003 11:44 AM Page 1

Produktspecifikationer

Varumärke: Horizon Fitness
Kategori: Cykeltränare
Modell: Avalon 100

Behöver du hjälp?

Om du behöver hjälp med Horizon Fitness Avalon 100 ställ en fråga nedan och andra användare kommer att svara dig




Cykeltränare Horizon Fitness Manualer

Cykeltränare Manualer

Nyaste Cykeltränare Manualer