Impact EX-100A Bruksanvisning

Impact Lampa EX-100A

Läs nedan 📖 manual på svenska för Impact EX-100A (20 sidor) i kategorin Lampa. Denna guide var användbar för 6 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Sida 1/20
EX-100A Monolight
INSTRUCTIONS
impactTM
Thank you for your purchase of the Impact EX-100A Monolight. The
EX-100A Monolight is economical and lightweight, yet durable enough to
give you many years of trouble-free service and enjoyment. Please read
these operating instructions and safet y precautions carefully before
operating this equipment.
Features
• Three-stop range – full power to 1/8 power, steplessly
• Built-in optical slave
• Modeling lamp can be set to proportional or full power
• Accepts Elinchrom-st yle reectors and head accessories
(8-inch grid reector included)
• Tactile, “grippy” feel that resists slipping, scratches, and shock damage
• Commonly available 1/8˝ mini-plug sync input
• Low 4.3V trigger voltage – safe for any camera’s circuitr y
Power Requirements
This light comes in two models; one is designed for use with 110/120V AC power in the US
and the other for 220V AC power in Europe. Neither model can be used outside of its
native power region. Both are supplied with a three-prong, grounded plug. Do not
attempt to defeat this safety feature. If necessary, use only grounded extension cords
rated for six amps or greater.
Warning
There are no user-serviceable parts inside the unit. Only qualied service engineers
should access the inside of the case (Danger – high-voltage parts inside). Avoid damage
to both the ashtube and modeling lamp. If the modeling lamp or ashtube become
cracked or damaged in any way, they should be replaced immediately. Do not use your
ash unit in an environment where moisture or ammable vapor is likely to come in
contact with the unit. Turn the power off and unplug the power cord when the unit is not
in use. Always remove the modeling lamp and replace the protective cap when
transporting the unit . Avoid strong light falling onto the slave cell as it will prevent
efcient operation. If the unit blows a fuse, a replacement fuse can be inserted in the
pull-out compartment on the back of the unit. To ensure long life of the ash capacitors,
the ash unit should be powered up and red several times at least every two months.
All images in this manual are for illustrative purposes only. Your unit may differ slightly from the one pictured.
Mount on a stand
(1) Select a stand or support
system of suitable weight
and dimensions to ensure
stable operation of the unit .
Install Reector &
Modeling Lamp
(2) Remove the protective
cap by pressing in and
turning it counter-
clockwise. Pull the cap off
and set aside.
(3) Install the modeling
lamp by screwing it into the
threaded socket.
CAUTION: Do not touch the lamp with your bare hands. Oil residue from yourngers can
cause the surface of the lamp to heat unevenly and explode. Use white cotton gloves or a
clean cloth.
(4) Install the reector where the protective cap was before. Align the two notches on
the reector with the white guidelines on theash unit , press the reector in and rotate
clockwise until it locks in place. Rotate the outer ring to secure the reector.
Note: Take care when tting or removing reectors or softboxes to not damage the
ashtube assembly. The ashtube is very delicate. Always switch off the unit and
disconnect the power before tting or changing lamps, ashtubes, reectors, or softboxes.
Preparing Your Monolight for Use
1
3 4
2

Produktspecifikationer

Varumärke: Impact
Kategori: Lampa
Modell: EX-100A

Behöver du hjälp?

Om du behöver hjälp med Impact EX-100A ställ en fråga nedan och andra användare kommer att svara dig




Lampa Impact Manualer

Lampa Manualer

Nyaste Lampa Manualer