Intergas Kombi Kompakt HRE 36/30 Bruksanvisning

Intergas Pannor & pannor Kombi Kompakt HRE 36/30

Läs nedan 📖 manual på svenska för Intergas Kombi Kompakt HRE 36/30 (4 sidor) i kategorin Pannor & pannor. Denna guide var användbar för 9 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF

Sida 1/4

Combi Compact

HRE 24/18

HRE 28/24

HRE 36/30

HRE 36/40

Operating Instructions

Installation of the appliance may only be carried out by an installer/competent person.

Please ask your installer to instruct you on how to fill and bleed the appliance and the

installation and on their operation. Strictly abide by all the instructions and warnings.

Always use the appliance in accordance with the Operating Instructions. It is forbidden to

interfere with a sealed component.

CONTENTS

1 Operation of the appliance 2

1.1 Operation of the central heating ................................................................. 2

1.2 Operation of domestic hot water supply ..................................................... 2

2 Operation and display read-out 2

2.1 Operating mode on the service display ...................................................... 3

2.2 Changing the settings of the various functions ........................................... 3

3 Start-up 3

4 Faults 3

5 Filling and bleeding appliance and installation 4

5.1 Central heating system ............................................................................... 4

5.2 Domestic hot water supply .......................................................................... 4

5.3 Frost protection ........................................................................................... 4

6 Maintenance 4

Intergas Heating Ltd is a licensed member of the Benchmark Scheme which aims to improve the standards of installation and commissioning of domestic

heating and hot water systems in the UK and to encourage regular servicing to optimise safety, efficiency and performance. Benchmark is managed and

promoted by the Heating and Hotwater Industry Council. For more information visit www.centralheating.co.uk. Please ensure that the installer has fully

completed the Benchmark Checklist on the inside back pages of the installation instructions supplied with the product and that you have signed it to say that

you have received a full and clear explanation of its operation. The installer is legally required to complete a commissioning checklist as a means of

complying with the appropriate Building Regulations (England and Wales). All Installations must be notified to Local Aerea Building Control either directly or

through a Competent Persons Scheme. A Building Regulations Compliance Certificate will then be issued to the customer who should, on receipt, write the

Notification Number on the Benchmark Checklist. This product should be serviced regularly to optimise its safety, efficiency and performance. The service

engineer should complete the relevant Service Record on the Benchmark Checklist after each service. The Benchmark cheklist may be required in the

event of any warrranty work and as supporting documentation relating to home improvements in the optional documents section of the Home Information

Pack.

1 OPERATION OF THE APPLIANCE

The purpose of the Intergas Combi Compact HRE wall mounted gas fired boiler is to heat water and to supply it to the central heating

(CH) system and the domestic hot water (DHW) taps. The heat exchanger comprises of two separate systems for central heating and

DHW. The appliance is fitted with a modulating control. This means that the power is adjusted in line with the required heat. The boiler

controller responds to each call for heat from the heating or the DHW system by igniting the burner and monitoring the flame.

1.1 Operation of the central heating

The call for heat arises as a result of the room temperature being lower than the temperature set on the room thermostat. If at that time

the appliance does not have a call for DHW, the appliance comes on in central heating mode. The central heating temperature control

modulates on the basis of the set central heating supply temperature. This means that when the desired central heating supply

temperature is approached the appliance adjusts the power. The pump for the central heating has a post purge period of 1 minute. The

post purge period may be changed if desired. The pump runs automatically for 10 seconds once every 24 hours to prevent blocking.

1.2 Operation of domestic hot water supply

The DHW system is started automatically as soon as more than 2 litres of water per minute are drawn. During delivery of hot tap water

no heat is supplied by the appliance to the central heating system.

For purposes of fast delivery of hot tap water a DHW comfort function has been installed in the controller. This function maintains the

temperature of the heat exchanger. The DHW comfort function has the following settings:

On: ( LED on) The appliance’s DHW comfort function is turned on continuously. In this mode the heat exchanger will be kept on

temperature to assure instant delivery of hot water.

Eco: ( LED on) The appliance’s DHW comfort function is an intelligent system. The appliance will adapt to the pattern of use of hot tap

water. As a result, the temperature of the heat exchanger will only be maintained in periods during which domestic hot water was drawn

on previous days.

Off: (Both LEDs off) The temperature of the heat exchanger is not maintained, as a result of which the delivery of hot tap water takes a

little time. If there is no need for rapid delivery of hot tap water, the DHW comfort function can be switched off.

2 OPERATION AND DISPLAY READ-OUT

Read

out

Operation

On / off

On / Off button

CH o

peration or setting maximum CH temperature

DHW / CH button, for setting desired temperature

DHW operation or setting DHW temperature

button

Desired temperature of CH or DHW in °C / CH water pressure (bar) / Fault code/ Time

+ button

Clock “on” CH enabled

Clock function setting

Clock “off” CH disabled

DHW comfort function off / eco / on

DHW comfort function eco

Service button

DHW comfort function on (continuous)

Reset button

Operating code

Flashes to indicate fault

2.1 Operating mode on the service display:

—

Off (appliance frost protection active)

Ventilate

Wait mode

Ignite

CH pump post run

CH mode

Desired temperature reached

DHW mode

Self test

Heat up appliance

Note: When the red LED above the reset key flashes a fault has occurred. A fault code will then appear on the temperature/clock display.

2.2 Changing the settings of the various functions

Keeping the key pressed for 2 seconds takes you to the user settings menu (LED at and the display starts to flash).

Then each time you press the key a different function LED will start to flash. The value of the function can be set using the

and keys. The value set is displayed on the display.

• The reset key closes the settings menu and stores the changes.

• If no key is pressed for 30 seconds, the settings menu is automatically closed and the changes are stored.

• The on/off key closes the settings menu without storing the changes.

• The button restores the default setting for the switch moments (hold for 5 seconds).

• By pressing the or keys the clock can be set and the switch moments can be defined.

• By pressing the button 2 time blocks can be programmed in which the CH is on (switch moments 1 to 4).

• By pressing the button the new times will be stored in the boiler controller. In the display appears [P] for a short period.

• Pressing the button for less than 1 second the following additional functions can be activated:

1. t-on (temporary on), the boiler will respond on every CH demand from the room thermostat until the next switch moment.

2. c-on (continuous on), the boiler will respond on every CH demand from the room thermostat without any time limit.

3. OFF, the boiler will not respond on any CH demand from the room thermostat.

. Can be set between 30°C and 90°C (standard setting 80°C). The maximum CH supply temperature

Low setting for moderately cold weather, high setting for colder weather.

DHW temperature.

Can be set between 40°C and 65°C (standard setting 55°C).

All other alterations of settings of the boiler may only be carried out by your installer.

3 START-UP

Once the appliance has been connected to water, gas and electricity supplies and

checked by an authorised installer, the appliance can be started.

Please check the following points:

• The central heating system and domestic hot water system must be well filled and bled.

• The appliance must be switched off (Horizontal dash on service display, other LEDs off).

• The water pressure in the central heating system must be between 1 and 2 bar (Shown on the temperature display).

Never switch the appliance on if the appliance, the CH system and the DHW system have not been completely filled and bled.

• The room thermostat must be set below the temperature in the room.

• The gas tap must be open.

• Switch the appliance on with the on/off key in the display (The LED lights up, and the service display goes out). The appliance

may now heat up for purposes of the DHW system until the heat exchanger reaches the set temperature.

• Set the clock and the switch moments. If the boiler is in a time block that CH is not active the boiler must be set in c-on (see §2.2).

• Set the room thermostat higher than the actual room temperature. The appliance will fire for purposes of the CH system.

4 FAULTS

If the following simple appliance faults occur, they can be resolved as follows. In the case of repeated occurrence or other faults

always notify your installer.

1. The CH system does not heat up or does not become sufficiently warm:

• Increase the temperature setting at the room thermostat.

• Open the radiator valves.

• Increase the CH water temperature setting using the and the and key on the operating panel (see §2).

• Bleed the appliance and installation and check the CH water pressure.

2. The domestic hot water supply does not become hot or hot enough:

• Open the domestic hot water tap further.

• Set the domestic hot water temperature higher using the and the and key on the operating panel (see §2).

3. The fault LED above the reset key is flashing. The following codes are indicated on the display (4):

• 1 The appliance becomes too hot, there is insufficient flow. Open the radiator valves, bleed the appliance and

installation and check the CH water pressure. If necessary top up (see §5 )

• 4 The burner does not light. Consult your installer.

Produktspecifikationer

Varumärke:	Intergas
Kategori:	Pannor & pannor
Modell:	Kombi Kompakt HRE 36/30
Frekvensomfång:	15 - 15000 Hz
Känslighet:	91 dB
Diameter woofer:	380 mm
Toppeffekt:	8000 W
Märkeffekt:	3000 W
Separerade komponenter:	Nee