JANDY VSSHP220AUT Bruksanvisning

JANDY Pomp VSSHP220AUT

Läs nedan 📖 manual på svenska för JANDY VSSHP220AUT (84 sidor) i kategorin Pomp. Denna guide var användbar för 4 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF

Sida 1/84

ePump™ Series

Pumps

ENGLISH | FRANÇAIS | ESPAÑOL

WARNING

INSTALLATION AND

OPERATION MANUAL

H0365700 RevE

FOR YOUR SAFETY - This product must be installed and serviced by a contractor who is licensed and qualified in pool

equipment by the jurisdiction in which the product will be installed where such state or local requirements exist. The

maintainer must be a professional with sufficient experience in pool equipment installation and maintenance so that

all of the instructions in this manual can be followed exactly. Before installing this product, read and follow all warning

notices and instructions that accompany this product. Failure to follow warning notices and instructions may result in

property damage, personal injury, or death. Improper installation and/or operation will void the warranty. Improper

installation and/or operation can create unwanted electrical hazard which can cause serious injury, property damage,

or death.

ATTENTION INSTALLER - This manual contains important information about the installation,

operation and safe use of this product. This information should be given to the owner/operator of this

equipment.

Table of Contents

Section 1. IMPORTANT SAFETY INSTRUCTIONS 3

1.1 Safety Instructions 3 ................................

1.2 Pool Pump Suction Entrapment

Prevention Guidelines 5 ..........................

Section 2. General Description 6 .............................

2.1 Introduction ........................................... 6

2.2 Description ............................................ 6

Section 3. Installation Information 7 .......................

3.1 Plumbing ............................................... 7

3.2 Electrical Installation 9 .............................

3.3 ePump Dip Switch Settings .................. 11

3.4 Pressure Testing ................................... 11

3.5 Conducting Pressure Test..................... 13

3.6 Auxiliary Load Operation 13 ......................

Section 4. Operation 15 ..............................................

4.1 Start-up ................................................. 15

Section 5. Service and Maintenance 15 ....................

5.1 Routine Maintenance 15 ............................

5.2 Winterizing the Pump 16 ...........................

Section 6. Troubleshooting and Repair 17 ...............

6.1 Troubleshooting .................................... 17

6.2 Service Technician Maintenance .......... 19

Section 7. Product Specications and Technical

Data 24 .......................................................

7.1 Replacement Parts List and Exploded

View 24 ......................................................

7.2 Performance Curves 26 .............................

7.3 Physical and Operational

Specications ....................................... 26

7.4 Replacement Motor Guide 27 ....................

DATE OF INSTALLATION

INSTALLER INFORMATION

INITIAL PRESSURE GAUGE READING (WITH CLEAN FILTER)

PUMP MODEL HORSEPOWER

NOTES:

EQUIPMENT INFORMATION RECORD

Page 2

Jandy® Pro Series ePump™ Series Pump | Installation and Operation Manual

ENGLISH

Section 1. IMPORTANT SAFETY INSTRUCTIONS

READ AND FOLLOW ALL INSTRUCTIONS

1.1 Safety Instructions

All electrical work must be performed by a licensed electrician and conform to all national, state, and local codes.

When installing and using this electrical equipment, basic safety precautions should always be followed, including the

following:

WARNING

To reduce the risk of injury, do not permit children to use this product.

WARNING

RISK OF SUCTION ENTRAPMENT HAZARD, WHICH, IF NOT AVOIDED, CAN RESULT IN SERIOUS

INJURY OR DEATH. Do not block pump suction, as this can cause severe injury or death. Do not

use this pump for wading pools, shallow pools, or spas containing bottom drains, unless the pump is

connected to at least two (2) functioning suction outlets. Drain covers must be certied to the latest

published edition of ANSI/ASME A112.19.8, or its successor standard ANSI/APSP-16.

WARNING

To reduce the risk of property damage or injury, do not attempt to change the backwash (multiport, slide,

or full ow) valve position with the pump running.

WARNING

Jandy Pro Series Pumps are powered by a high-voltage electric motor and must be installed by a

licensed or certied electrician or a qualied swimming pool service technician.

WARNING

Due to the potential risk of re, electric shock, or injuries to persons, Jandy Pro Series Pumps must be

installed in accordance with the National Electrical Code ® (NEC®), all local electrical and safety codes, and

the Occupational Safety and Health Act (OSHA). Copies of the NEC may be ordered from the National

Fire Protection Association, 470 Atlantic Ave., Boston, MA 02210, or from your local government inspection

agency.

WARNING

Incorrectly installed equipment may fail, causing severe injury or property damage.

WARNING

• Do not connect system to an unregulated city water system or other external source of pressurized

water producing pressures greater than 35 PSI.

• Trapped air in the system can cause the lter lid to be blown off, which can result in death, serious

personal injury, or property damage. Be sure all air is out of the system before operating.

WARNING

RISK OF ELECTRIC SHOCK, FIRE, PERSONAL INJURY, OR DEATH. Connect only to a branch

circuit that is protected by a ground-fault circuit-interrupter (GFCI). Contact a qualied electrician if you

cannot verify that the circuit is protected by a GFCI. Make sure such a GFCI should be provided by

the installer and should be tested on a routine basis. To test the GFCI, push the test button. The GFCI

should interrupt power. Push the reset button. Power should be restored. If the GFCI fails to operate

in this manner, the GFCI is defective. If the GFCI interrupts power to the pump without the test button

being pushed, a ground current is owing, indicating the possibility of electrical shock. Do not use the

device. Disconnect the device and have the problem corrected by a qualied service representative

before using.

Page 3

ENGLISH

Jandy

Pro Series ePump™ Series Pump | Installation and Operation Manual

Produktspecifikationer

Varumärke:	JANDY
Kategori:	Pomp
Modell:	VSSHP220AUT
Färg på produkten:	Beige, Brown
Bredd:	80 mm
Djup:	25 mm
Höjd:	80 mm
Sladdlängd:	0.3 m
Förpackningens vikt:	250 g
Förpackningens bredd:	150 mm
Djuppackning:	34 mm
Förpackningshöjd:	210 mm
Snäll:	Ventilator
Ljudnivå (hög hastighet:	17.7 dB
Certifiering:	CE
Nätförsörjning:	0.75 W
Hållbarhetscertifikat:	RoHS
Luftflöde:	55.5 m³/uur
Antal fans:	1 ventilator(en)
Spännande:	5 V
Rotationshastighet (max):	2200 RPM
Inklusive skruvar:	Ja
Rotationshastighet (min):	450 RPM
(Ytter) huvudpaketets höjd:	390 mm
(Ytter) huvudförpackningens bredd:	375 mm
(Ytter) huvudförpackningens bruttovikt:	11500 g
(Ytre) huvudpaketets längd:	360 mm
Kvantitet per (yttre) huvudkartong:	40 stuk(s)
Lämplig plats:	Computer behuizing
Kompatibla processorer:	Niet ondersteund
Harmoniserad systemkod (HS):	84733080
Ventilator diameter:	80 mm
Ström (max.):	0.15 A
Antal fläktblad:	7
Processorsocklar som stöds:	Niet ondersteund
Maximalt lufttryck:	2.37 mmH2O
Stöd för pulsbreddsmodulering:	Ja
Typ av lager:	Self-Stabilising Oil-pressure Bearing (SSO)
Fläktkontakt:	4-pin
Antivibrationssystem:	Ja
Mean Time To Failure (MTTF):	150000 uur