Milwaukee 2155-AC Bruksanvisning

Milwaukee Ficklampa 2155-AC

Läs nedan 📖 manual på svenska för Milwaukee 2155-AC (12 sidor) i kategorin Ficklampa. Denna guide var användbar för 8 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF

Sida 1/12

Cat. No. / No de cat.

2155-AC

ADIUS™

LED 70W TEMPORARY SITE LIGHT

LAMPE À DEL TEMPORELLE À 70 W

LÁMPARA DE TRABAJO TEMPORAL DE LED DE 70 W

OPERATOR'S MANUAL

MANUEL de L'UTILISATEUR

MANUAL del OPERADOR

WARNING To reduce the risk of injury, user must read and understand operator's manual.

AVERTISSEMENT An de réduire le risque de blessures, l'utilisateur doit lire et bien

comprendre le manuel.

ADVERTENCIA Para reducir el riesgo de lesiones, el usuario debe leer y entender el manual.

IMPORTANT SAFETY

INSTRUCTIONS

WARNING

Read all safety warn-

ings and all instruc-

tions. Failure to follow

the warnings and instructions may result in electric

shock, re and/or serious injury. Save all warnings

and instructions for future reference.

WORK AREA SAFETY

• To reduce the risk of injury, close supervision is

necessary when an appliance is used near children.

• Store idle light out of reach of children. Warm

lights can become hazcardous in the hands of chil-

dren.

ELECTRICAL SAFETY

• Power cord plugs must match the outlet. Never

modify the plug in any way. Do not use any

adapter plugs with earthed (grounded) power

tools. This product has a polarized plug (one

blade is wider than the other). This plug will t

in a polarized outlet only one way. If the plug

does not t fully, reverse the plug. If it still does

not t, contact a qualied electrician. Unmodied

plugs and matching outlets will reduce risk of electric

shock.

• Avoid body contact with earthed or grounded

surfaces, such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric

shock if your body is earthed or grounded.

• Suitable for damp locations. Store indoors.

• To reduce the risk of electric shock, do not put

light in water or other liquid. Do not place or store

appliance where it can fall or be pulled into a tub or

sink.

• Secure wiring cover and hanging cable before use.

• Do not abuse the cord. Never use the cord for car-

rying, pulling or unplugging the power tool. Keep

cord away from heat, oil, sharp edges or moving

parts. Damaged or entangled cords increase the risk

of electric shock.

• Keep cords dry and o󰀨 the ground. Arrange

cords carefully to avoid hazardous environ-

ments. Tripping or snagging on cords can cause

injury and product damage. Do not allow cords to

run through puddles or across wet ground.

• Do not unplug by pulling on the cord. To unplug,

grasp the plug, not the cord.

• Unplug the cord from outlet when not in use and

before servicing or cleaning.

• Always use a suitable extension cord to reduce

the risk of electric shock.

• Connect to a properly grounded outlet. If operat-

ing a light in a damp location is unavoidable, use

a ground fault circuit interrupter (GFCI) protected

supply. Use of an GFCI reduces the risk of electric

shock.

• A maximum of three 10 AWG through branch

circuit conductors suitable for 60°C permitted in

box. Suitable for Types NM and MC cable only.

•

Always install light in accordance with local and

national codes.

•

CAUTION

Do not use in hazardous locations

as required by the Canadian

Electrical Code Part 2.

PERSONAL SAFETY

• Do not overreach. Keep proper footing and bal-

ance at all times. This enables better control of the

light in unexpected situations.

• Do not use on a ladder or unstable support.

Stable footing on a solid surface enables better

control of the light in unexpected situations.

SERVICE

• Have your light serviced by a qualied repair per-

son using only identical replacement parts. This

will ensure that the safety of the light is maintained.

SPECIFIC SAFETY RULES

•Maintain labels and nameplates. These carry im-

portant information. If unreadable or missing, contact

a MILWAUKEE service facility for a free replacement.

EXTENSION CORDS

Grounded tools require a three wire extension cord.

Double insulated tools can use either a two or three wire

extension cord. As the distance from the supply outlet

increases, you must use a heavier gauge extension

cord. Using extension cords with inadequately sized

wire causes a serious drop in voltage, resulting in loss

of power and possible tool damage. Refer to the table

shown to determine the required minimum wire size.

The smaller the gauge number of the wire, the greater

the capacity of the cord. For example, a 14 gauge cord

can carry a higher current than a 16 gauge cord. When

using more than one extension cord to make up the

total length, be sure each cord contains at least the

minimum wire size required. If you are using one exten-

sion cord for more than one tool, add the nameplate

amperes and use the sum to determine the required

minimum wire size.

Guidelines for Using Extension Cords

• Be sure your extension cord is properly wired and in

good electrical condition. Always replace a damaged

extension cord or have it repaired by a qualied person

before using it.

• Protect your extension cords from sharp objects,

excessive heat and damp or wet areas.

• When stringing lights together, consider the total

Amperes draw when selecting the extension cords.

Recommended Minimum Wire Gauge

For Extension Cords*

Extension Cord Length

Nameplate

Amperes 25' 50' 75' 100' 150'

0 - 2.0

2.1 - 3.4

3.5 - 5.0

5.1 - 7.0

7.1 - 12.0

12.1 - 16.0

16.1 - 20.0

* Based on limiting the line voltage drop to ve volts at 150%

of the rated amperes.

READ AND SAVE ALL INSTRUCTIONS

FOR FUTURE USE.

GROUNDING

DANGER

Improperly connecting the ground-

ing wire can result in the risk of

electric shock. Check with a qualied electrician if

you are in doubt as to whether the outlet is prop-

erly grounded. Do not modify the plug provided

with the tool. Never remove the grounding prong

from the plug. Do not use the tool if the cord or

plug is damaged. If damaged, have it repaired by a

MILWAUKEE service facility before use. If the plug

will not t the outlet, have a proper outlet installed

by a qualied electrician.

Double Insulated Tools (Two-Prong Plugs)

Tools marked “Double Insulated” do not require ground-

ing. They have a special double insulation system which

satises OSHA requirements and complies with the

applicable standards of Underwriters

Fig. B Fig. C

Laboratories, Inc., the Canadian Stan-

dard Association and the National Elec-

trical Code. Double Insulated tools may

be used in either of the 120 volt outlets

shown in Figures B and C.

SPECIFICATIONS

Cat. No. 2155-AC ....................................................

AC Input Volts ............................................ 120-277

AC Input Watts 70 ....................................................

AC Output Volts ......................................... 120-277

Max Terminal Block Ampacity ..............................30

Wiring ....................... Romex and MC, 14-2 to 10-3

Consult with Local and National Electrical Codes

FUNCTIONAL DESCRIPTION

1. Wiring Cover

2. Cover screw

3. Cable

4. Wire clamps

5. AC input/output

6. Cable clamp

7. LED cover

123

SYMBOLOGY

Volts

Alternating Current

Electrical Shock Hazard

Read Operator's Manual

CAUTION

Bright Light -

Do Not Stare Into Light

Double Insulated

C US

UL Listing for Canada and U.S.

ASSEMBLY

WARNING

To reduce the risk of injury, always

unplug tool before changing or

removing accessories. Only use accessories

specically recommended for this tool. Others

may be hazardous.

Conversion to Permanent Wiring

WARNING! Always install light in accordance with

local codes.

To add lights in a chain, or replace the wiring:

1. Unplug the light.

2. Open the wiring cover by turning the cover screw

1/4 turn counterclockwise.

3. Remove and discard old wiring.

4. To add wiring, expose 3 to 4 inches of the wires

from the outer jacket/armor.

5. Feed the wire through the AC input/output holes, and

butt the outer jacket/armor up against the wire clamps.

6. Tighten the wire clamps using the clamping screws.

Hand tighten wire clamp screws securely to 8 lb-in.

7. Wire the lamp according to the diagrams below.

Use one side for wiring to the AC plug, and the

other for wiring to another lamp in a chain. Hand

tighten terminal block screws securely to 10 lb-in.

8. Close the wiring cover and secure by turning the

cover screw 1/4 turn clockwise.

Strain

Relief

AC Input/

Output Holes

Wire

clamps

Clamping

screws

Produktspecifikationer

Varumärke:	Milwaukee
Kategori:	Ficklampa
Modell:	2155-AC

Behöver du hjälp?

Om du behöver hjälp med Milwaukee 2155-AC ställ en fråga nedan och andra användare kommer att svara dig

Ditt namn*

Din e-post*

Skriv din fråga här

Ficklampa Milwaukee Manualer

Milwaukee L4 FL2000 Bruksanvisning

21 September 2024

Milwaukee L4 NL400 Bruksanvisning

21 September 2024

Milwaukee L4 SL550 Bruksanvisning

21 September 2024

Milwaukee L4 BOLTHL Bruksanvisning

21 September 2024

Milwaukee L4 HL2 Bruksanvisning

21 September 2024

Milwaukee L4 FL Bruksanvisning

21 September 2024

Milwaukee L4 HSL Bruksanvisning

21 September 2024

Milwaukee HL2-LED Bruksanvisning

21 September 2024

Milwaukee L4 FFL Bruksanvisning

21 September 2024

Milwaukee L4 FMLED Bruksanvisning

21 September 2024

Ficklampa Manualer

Nyaste Ficklampa Manualer

Stanley SL5W09 Bruksanvisning

17 Oktober 2024

Ledlenser P9R Core LEP Bruksanvisning

15 Oktober 2024

LED Lenser P5R Bruksanvisning

11 Oktober 2024

Nordride 5110 Spor Smart A Bruksanvisning

7 Oktober 2024

Varta 17631 Bruksanvisning

7 Oktober 2024

Varta 18803 Bruksanvisning

4 Oktober 2024

LED Lenser L5 Bruksanvisning

2 Oktober 2024

Black Diamond Ember Bruksanvisning

2 Oktober 2024

Brennenstuhl TL 1201 AF Bruksanvisning

1 Oktober 2024

Brennenstuhl TL 601 AF Bruksanvisning

1 Oktober 2024