Nitek WB5362 Bruksanvisning

Nitek Wifi-repeater WB5362

Läs nedan 📖 manual på svenska för Nitek WB5362 (6 sidor) i kategorin Wifi-repeater. Denna guide var användbar för 11 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF
Sida 1/6
WB5326
Wireless Bridge
Quick Start Guide
01/09/12
2
Quick Start Guide
WB5326 Outdoor Wireless Bridge
Items Included in Kit
(1) WB5326 RADIO
(1) PoE (48V, 1A)
(1) Mounting Hardware Accessories
(1) Quick Start Guide
(1) Product CD
Hardware Installation
1. Put an Ethernet cable with RJ-45 connector through the water-tight joint. Make the RJ-45 connector as a 568B
wiring configuration:
2. Using the hardware provided mount the Bridge unit in position. Make sure that the Ethernet connection is
facing down. Keep in mind that the unit has a built-in antenna and must have line of sight between units. Refer
to separate mounting guide sheet for illustrations of hardware assembly.
3. Plug water-tight joint side of the Ethernet cable into the Bridge unit. Connect the other end of the cable to the
power injector supplied with the unit. Also connect a standard RJ-45 network cable for the power injector to a
hub or a terminal.
4. There is a ground connection on enna port. The ground connection should the Bridge unit located near the ant
be connected to a proper earth ground point.
5. The antenna of the Bridge unit is behind the plastic face of the unit and must face the other Bridge unit. Make
sure you have line of site to the opposite unit and that they face each other.
Warning Do not mount Bridge unit near electric power lines, electric
lights or near strong electric power signals
6. Power the unit using the supplied PoE inserter.
12345678
568B
21 4
3
Terminal Wire
1 Orange/White
2 Orange
3 Green/White
4 Blue
5 Blue/White
6 Green
7 Brown/White
8 Brown
3
These instructions are designed for configuring this system to be a network Bridge.
1. Power up each Bridge unit for 30 seconds, then RESET it by pressing the Reset button for 10 seconds.
2. On the PC you will be using to setup the Bridge units, select “Network Connections” in the control Panel. You
can get to it by Start>Settings>Control Panel>Network Connections. Locate the “Local Area Connection”
and right click to select “ ”. When in that tab select “Properties Internet Protocol (TCP/IP)”.
3. Set up a computer with a network IP address of:
IP address 192.168.1.100
Subnet 255.255.255.0
Gateway 192.168.1.254
4. Select and note an IP address for each Bridge unit along with an ID name and password for each unit (see
Example 1). You will also need to select a Channel from 1-11 for all units. Bridge units are designed to work as a
pair. Both units of the pair must operate on the same channel. Different sets should use different channels. For
maximum data speed separate sets by 4 channels or more (i.e., 1, 6, 11).
* Each pair of units must operate on the same channel (1 - 11). Different pairs should use different channels.
Example 1
Unit Your IP Address
For each unit Password Unit ID Channel*
1 xxx.xxx.xxx.1 Build 1 Building One 1
2 xxx.xxx.xxx.2 Build 2 Building Two 1
3
4
5
6

Produktspecifikationer

Varumärke: Nitek
Kategori: Wifi-repeater
Modell: WB5362

Behöver du hjälp?

Om du behöver hjälp med Nitek WB5362 ställ en fråga nedan och andra användare kommer att svara dig


Wifi-repeater Nitek Manualer

Nitek

Nitek WB5362 Bruksanvisning

23 Augusti 2024

Wifi-repeater Manualer

Nyaste Wifi-repeater Manualer

TP Link

TP Link RE220 Bruksanvisning

8 Januari 2025
Manhattan

Manhattan 525664 Bruksanvisning

8 Januari 2025
D-Link

D-Link DMG-112A Bruksanvisning

6 Januari 2025
Mercusys

Mercusys Halo H1200G Bruksanvisning

4 Januari 2025
HELGI

HELGI HLG0372 Bruksanvisning

3 Januari 2025
Medion

Medion P85032 (MD 87070) Bruksanvisning

31 December 2025
TP Link

TP Link RE3000X Bruksanvisning

31 December 2025
Hawking Technologies

Hawking Technologies HOW2R1 Bruksanvisning

15 Oktober 2024
Planet

Planet WNAP-1110 Bruksanvisning

10 Oktober 2024
Netgear

Netgear WN2000RPTv2 Bruksanvisning

10 Oktober 2024