NTech Skywatch GEOS 9 Bruksanvisning

NTech Diverse Skywatch GEOS 9

Läs nedan 📖 manual på svenska för NTech Skywatch GEOS 9 (10 sidor) i kategorin Diverse. Denna guide var användbar för 2 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Sida 1/10
Owner’s Instructions
NTech USA
PO Box 882
La Crosse, WI 54602
608.498.4021 (phone)
608.531.2608 (fax)
www.ntechusa.com
info@ntechusa.com
You have just acquired a high precision instrument, manufac-
tured using the most up-to-date technology. The Skywatch
was designed to handle intense use and extreme condi-
tions. Please take the time to carefully read your instructions so
as to understand all the great features this unit has to offer.
Buttons Uses:
Turn your on by pushing either the
wind
or
mode
button.
Push the
wind
button to choose between maximum or average
wind speed.
Press and hold the
wind
button to switch the wind speed
measurement unit: km/h, m/s, knots or mph.
Push the
mode
button to choose between current temperature,
WindChill Factor, pressure, pressure historical records and
altitude.
Press and hold the
mode
button to switch temperature unit:
˚C or ˚F.
Extreme values of wind speed and temperature can be deleted
by pressing both the
wind
and
mode
buttons simultaneously.
Push the clock button to set the
clock
timer.
Current Temperature:
The temperature sensor is located on the left corner, over the
display. In the event of severe temperature changes, allow a
few moments for the sensor to reach the current temperature.
Select the current temperature with the
mode
button. Current temperature is displayed
at the bottom of the LCD either in ˚C or ˚F. To change the unit of measurement, press
the
mode
button for 2 seconds.
Please note that holding the instrument in your hands for a while may influence the
temperature reading. The sensor is very sensitive.
1. Button wind
2. Button clock
3. Button mode
All segments
of the LCD
1 2 3
Owner’s Instructions SKYWATCH®
Geos
Minimum and Maximum Temperatures:
Minimum and Maximum temperatures are permanently displayed.
Extreme values will flash on the bargraph. When your instru-
ment is on standby, temperature is measured every thirty (30)
minutes, allowing a recording of the extreme values, even when
the instrument is turned off.
Extreme temperature values can be deleted by pressing both the
wind
and
mode
buttons simultaneously.
Minimum and maximum temperature
measurement displayed
with flashing lines on the bargraph
Wind-chill Factor:
The wind-chill factor is a calculation of the effect of wind on
temperature. It portrays an indication of the loss of heat by
your body in case of temperatures below 37˚C and the aug-
mentation of the heat with a temperature over 37˚C and wind.
For instance, with a 0˚C current temperature and a 40 km/h
blowing wind, your body will use as much heat as if it would
be exposed to a temperature of -15 ˚C with no wind. This value
of -15˚C is called wind-chill factor. Wind-chill factor can be
selected by pressing the
mode
button. The corresponding
symbol is then displayed in the bottom of the LDC.
Pressure:
The pressure sensor is located inside the instrument. The indicated pressure is the
actual pressure at the instrument’s altitude and not the reported pressure at sea level.
Temperature in Celcius and
Fahrenheit degree
Changing of temperature unit
(ºC and ºF)
Wind-chill
factor mode

Produktspecifikationer

Varumärke: NTech
Kategori: Diverse
Modell: Skywatch GEOS 9

Behöver du hjälp?

Om du behöver hjälp med NTech Skywatch GEOS 9 ställ en fråga nedan och andra användare kommer att svara dig




Diverse NTech Manualer

Diverse Manualer

Nyaste Diverse Manualer