Oliveri NP6101TH Bruksanvisning

Oliveri Sjunka NP6101TH

Läs nedan 📖 manual på svenska för Oliveri NP6101TH (2 sidor) i kategorin Sjunka. Denna guide var användbar för 4 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF

Sida 1/2

SPECIAL INSTRUCTIONS FOR PARTICULAR TOP MOUNT SINK MODELS

CAUTION

Leave protective tape on the sink when inverting over a benchtop and tracing its shape. The stainless

steel will scratch if the sink slides across a hard surface.

Topmount sinks may also be known as “drop in” or “inset” sinks.

Topmount models with prex PR, SN, NP, MO, DZ, PE, LL, UF, PL, MR, EL & TI.

These sinks will t into standard 600mm bench tops.

Templates are available for download from www.oliverisinks.com

Download PDF template from www.oliverisinks.com. If the template is not available, the cutout shape may be created by

carefully inverting the sink onto the counter/benchtop and tracing around the perimeter.Cut the hole 10mm inside the traced line.

Many Oliveri sinks have waste outlets positioned to the rear of the bowls. Ensure the sink is correctly positioned when tting.

Unequal bowl depth:

Sinks that combine different sized bowls may also have unequal bowl depth. Waste plumbing will need to

accommodate this variance. All sinks have a height adaptor included with the sink where needed.

Solitaire models (LR)

LR510 & LR515 may be top mounted, each using a circular cutout 466mm in diameter. LR515 comes with a 32mm diameter

taphole pre-cut in the tap landing. Mark the location of this taphole when trial tting the sink. Then, drillout the counter/benchtop

in the appropriate location so that the mixer tap can be solidly installed through both the sink and the counter/benchtop.

LR510 may also be under mounted in a solid-surface counter/benchtop using a circular cut out 454mm in diameter

after edges are smoothed. Refer Oliveri undermount instructions for recommended installation methods.

MATERIALS FOR FITTING THE UNDERMOUNT SINK:

• Oliveri sink (with correct tap holes as ordered) - includes mounting clips,

sealing gasket, basket wastes and other accessories (depending on

model).

• These Installation Instructions

• Level to check counter/benchtop & sink is installed level

• Phillips head screwdriver (#2 to tighten mounting clips)

• Flat head screwdriver (large - to tighten basket wastes)

• Suitable sealant (neutral-cure silicone sealant or equivalent)

• Masking material to protect counter/benchtop and sink from excess

sealant

• Additional Mounting Hardware if tting into thinner material. The

clamps included with the sink require a minimum counter/benchtop

thickness of 25mm / 1”.

INSTALLER - PLEASE READ & FOLLOW THESE

INSTALLATION INSTRUCTIONS

Please retain for consumer as care instructions are included

IT IS HIGHLY RECOMMENDED THE ACTUAL SINK BE PRESENT AT TIME OF CUTTING

Any advice, recommendation, information, assistance or service provided by Tasman Sinkware in

relation to goods manufactured by it or their use and installation, is given in good faith and is believed by

Tasman Sinkware to be appropriate and reliable. However, any advice, recommendation, information,

assistance or service is provided by Tasman Sinkware without responsibility or liability.

FOR “TOP MOUNT” OR “DROP IN” SINKS

CHECK MODEL

The model number on the sink

packaging must match the model

of sink the customer ordered.

Do not install if incorrect.

AVOID CUTS

The perimeter and punch-outs on

the sink may contain sharp edges.

Handle the sink carefully to avoid

personal injury.

CHECK THE CONDITION

Inspect the sink for any visible

defects. Do not install the sink if

defects are found. Contact your

sink retailer / point of purchase.

AVOID SCRATCHES

Stainless steel can be scratched

if proper care is not taken during

installation.

Do wnload cutout

template files

(PDF, & F) DWG DX

from our website.

AUSTRALIA

Head Ofce &

Manufacturing Plant

Tasman Sinkware Pty Ltd

Regency Park SA

Phone: +61 8 8348 6444

Fax: +61 8 8348 6495

Email: sinkware@oliverisinks.com.au

oliveri.com.au

TF 08f May 2017

FOLLOW THESE STEPS TO INSTALL THE OLIVERI TOP MOUNT SINK

IF COUNTER / BENCHTOP IS SUPPLIED WITH CUT-OUT, SKIP STEPS MARKED WITH*

ADDITIONAL SEALANT

Apply additional sealant / caulking compound around the join where the counter/

benchtop and the stainless steel sink meet. Check that the caulking product is

mildew resistant and is suitable for use on the counter/benchtop material and also

is suitable for use on stainless steel. Clean away any excess before it dries. Note:

Additional sealant should always be used if gaps are apparent after the sink has

been clamped to the counter/benchtop

FITTING THE SINK If you choose to mount the tap / faucet onto the sink prior

to tting, take extra care as it will change the weight and balance of the sink.

Position and align the sink correctly in the cutout and lower it onto the counter/

benchtop. From underneath, tighten the clips with a screwdriver using a suitable

tightening sequence (tighten from the centre of the sink to the outer edge) until

the sink is secure and no gaps are visible. Take extra care if using power tools as

over-tightening can damage clips.

FINAL CHECK OF FOAM SEAL With the sink tightened down. Visually conrm

the foam seal is not protruding anywhere underneath. If it does, undo all the

clips, reposition the foam seal and tighten down again. If the foam seal has been

damaged, replace the damaged section. If the tap/faucet was mounted prior to

tting – check that the position is correct.

PLUMBING & TAPWARE

IMPORTANT - Connections to plumbing should always be done by a licensed

plumber. Fit supplied basket wastes to sink bowls. Install tapware according to

manufacturer’s instructions. Care should be taken when tting wastes to the sink.

Follow the instructions provided with the wastes.

DO’s

• Clean with soap & water (towel dry)

• Clean along the grain of the Stainless Stee

• Use a soft brush or sponge (old tooth brush)

• Wipe over with a glass cleaner (Windex is very good)

• Polish with a metal polish paste (Autosol / Brasso)

• Use a Liquid cleaner (Bon-Ami or Jiff)

• Use a granulated stainless steel cleaner (Essteele)

DO NOT’s

• NEVER use Steel wool

• Beware of harsh liquid cleaners

• Beware of grit within cloths and mineral deposits within water

• Avoid prolonged exposure to acids from Fruit, Fruit juices, Salts, Spirits, Bleach, Tea-bags

• Avoid prolonged contact with ordinary steel which can rust Tin Cans, Steelwool

• Do not keep harsh (acids or chlorine) chemicals under sink / laundry tub

• Do not leave chlorine/chloride chemicals on stainless steel surface

• Do not leave liquid soaps & cleaners to dry on stainless steel

• Do not use bleaches (White King, Domestos, Clorox)

INSTRUCTIONS CONTINUE OVER PAGE

It is essential that the installation is waterproof and carried out in accordance with these instructions. Tasman

Sinkware will not be held responsible for any damage caused by leakage or faulty installation.

CARE INSTRUCTIONS FOR YOUR OLIVERI STAINLESS STEEL SINK

AVOID CONTACT WITH ROUGH OR DIRTY SURFACES as new polished stainless steel will show scratches!

CHECK SPACE & LEVEL

Use a level to check the counter/benchtop – if not level, have rectied. Ensure

there is adequate space for tapware (including a splash back if specied). Check

space for installation (underneath) and operation (above). Particular care must be

taken when a thick splash back is used (it may interfere with tapware location and

operation). Ensure the cabinet will not foul the sink mounting ange or basins.

TEMPLATE *

Cut out templates for your Oliveri sink are available online at oliverisinks.com.

Use the product model number to nd the template. Some sink templates apply

to both left-hand and right-hand models sinks. Ensure template is correct way

around for your model. (If no template is available, carefully invert the sink over

the counter/benchtop and trace around it.)

MARK CUT OUT *

Carefully mark out the template (or follow drawing instructions). Once the hole is

marked out, use the template to conduct a nal check before cutting.

IMPORTANT

If you have traced the sink itself to mark your cut out, the hole must be cut

10mm inside the marked line.

CUT & FINISH HOLE *

Re-check the position and cut out shape you have traced before cutting. Ensure

there are no obstacles below that might interfere with cutting. Drill pilot holes

to accept an appropriate cutting tool for the counter/benchtop material (wear

suitable personal protection equipment). Cut just inside the template mark (or

10mm inside the sink tracing).

TRIAL FIT THE SINK

Check that all clips are folded in so they will adequately clear the cut-out.

Carefully position the sink into the cut-out to make sure it ts correctly. If the t is

not correct, remove the sink and proceed with remedial work. Perform another

trial t after corrections have been made.

MASKING

If using a sealant, masking is necessary to prevent sealant overrun. It is

recommended that the edge of the sink and the edge of the cutout are both

covered with a suitable masking tape. This tape should be removed within 2 days

of application.

CHECK FOAM SEAL

Make sure the foam seal is intact and ts all the way around the sink with no gaps

visible. This will ensure a water tight seal when the sink is properly tightened

down to the counter/benchtop.

PR/SN models require sealant only and do not include a foam seal.

TF 08f May 2017

Produktspecifikationer

Varumärke:	Oliveri
Kategori:	Sjunka
Modell:	NP6101TH
Färg på produkten:	Zwart
Bredd:	62 mm
Djup:	62 mm
Höjd:	17 mm
Sladdlängd:	1.2 m
Instruktioner:	Ja
Nuvarande:	1.1 A
Typ av strömkälla:	AC
Snabbladdning:	Ja
Antal per paket:	1 stuk(s)
Inspänning:	100 - 240 V
Strömspänningsskydd:	Over current, Over voltage, Short circuit
Frekvens:	50-60 Hz
Utström:	3000 mA
Maximal kraft:	45 W
Typ-av-laddare:	Binnen
Laddare kompatibilitet:	Universeel
Utspänning (max):	20 V
Antal USB Type-C-portar:	1
Utspänning (min):	5 V
Snabbladdningsteknik:	Quick Charge 3.0
Automatisk utspänningsjustering:	Ja