Oliveri PR1131 Bruksanvisning

Oliveri Sjunka PR1131

Läs nedan 📖 manual på svenska för Oliveri PR1131 (4 sidor) i kategorin Sjunka. Denna guide var användbar för 3 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF

Sida 1/4

INSTALLER - PLEASE READ & FOLLOW

THESE INSTALLATION INSTRUCTIONS

Please retain for consumer as care instructions are included

EQUIPMENT REQUIRED for installing your Oliveri top mount sink:

MATERIALS FOR CUTTING COUNTER/BENCHTOP:

• Template for your particular model sink and mounting method (may be inside or printed

on carton depending on model). If not available, the sink itself may be used.

• Marker such as a pencil or similar for tracing the template onto the counter/benchtop

• Tape measure

• Drill with 12mm / ½” diameter bit or larger (wood counter/benchtop)

• Cutting Device (such as a jigsaw) with suitable blade for counter/benchtop material

• Suitable protection such as gloves and goggles to be used while drilling or cutting

MATERIALS FOR FITTING THE TOP MOUNT SINK:

• Oliveri sink (with correct tap holes as ordered) - includes mounting clips, sealing gasket,

basket wastes and other accessories (depending on model).

• These Installation Instructions

• Level to check counter/benchtop & sink is installed level

• Phillips head screwdriver (#2 to tighten mounting clips)

• Flat head screwdriver (large - to tighten basket wastes)

• Suitable sealant (neutral-cure silicone sealant or equivalent)

• Masking material to protect counter/benchtop and sink from excess sealant

• Additional Mounting Hardware if fitting into thinner material. The clamps included

with the sink require a minimum counter/benchtop thickness of 25mm / 1”.

CHECK MODEL & TAP HOLES

The model number on the sink

packaging must match the model

of sink the customer ordered.

Check the number and position of

tap holes is correct.

Do not install if incorrect.

CHECK THE CONDITION

Inspect the sink for any visible

defects. Do not install the sink if

defects are found. Contact your

sink retailer / point of purchase.

AVOID CUTS

The perimeter and punch-outs on

the sink may contain sharp edges.

Handle the sink carefully to avoid

personal injury.

AVOID SCRATCHES

Polished stainless steel can be

scratched if proper care is not

taken during installation.

Topmount sinks may also be known as “drop in” or “inset” sinks.

Sink models with prefix MO, PE, UF, DU, LR, EF, NP, MR, SI & RR.

These sinks will fit into standard 600mm bench tops.

Templates supplied are to assist in achieving the correct shape hole for top mounting the sink.

Careful use of the template is required to achieve the correct cutout shape. If the template is not available, the cut out shape may

be created by carefully inverting the sink onto the counter/benchtop and tracing around the perimeter. Cut the hole 10mm inside the

traced line.

Many Oliveri sinks have waste outlets positioned to the rear of the bowls. Ensure the sink is correctly positioned when fitting.

Unequal bowl depth:

Sinks that combine different sized bowls may also have unequal bowl depth. Waste plumbing will need to accommodate

this variance. MO, PE, NP, SI & RR sinks have a height adaptor included with the sink where needed.

Models UF03D & UF04D have a 60mm height difference in waste connections for the main and smaller bowl. Waste plumbing will

need to accommodate this variance.

Models UF05D & UF06D have a 35mm height difference in waste connections for the main and smaller bowl. Waste plumbing will

need to accommodate this variance.

EF models have a 35mm height difference in waste connections for the main and smaller bowl. Waste plumbing will need to

accommodate this variance.

Solitaire models (LR) - Cut out templates are not supplied with these sinks.

LR510 & LR515 may be top mounted, each using a circular cut out 466mm in diameter. LR515 comes with a 32mm diameter tap

hole pre-cut in the tap landing. Mark the location of this t nchtop in the ap hole when trial fitting the sink. Then, drill out the counter/be

appropriate location so that the mixer tap can be solidly nk and the counter/benchtop. installed through both the si

For other topmount LR models that do not have a template, the cut out shape may be created by carefully inverting the sink onto

the counter/benchtop and tracing around the perimeter. Cut the hole 10mm inside the traced line.

LR510 may also be under mounted in a solid-surface counter/benchtop using a circular cut out 454mm in diameter after

edges are smoothed. Refer Oliveri undermount instructions for recommended installation methods.

MANHATTAN & DALLAS (MH or DA)

THESE SINKS WILL NOT FIT IN A STANDARD 600MM COUNTER/BENCH TOP.

Measure carefully to ensure sufficient room exists (including allowance for a splashback if required). The cutout shape may

be created by carefully inverting the sink onto the counter/benchtop and tracing around the perimeter. Cut the hole 10mm inside the

traced line.

FOR “TOP MOUNT’ OR “DROP IN” SINKS

NORTH AMERIC

Sales Office

Tasman Sinkware North America

Corona CA

Email: northamerica@oliverisinks.com

UNITED KINGDOM DISTRIBUTOR

A.C. Toon Ltd

Phone: 01246 223900

Email: sales@actoon.co.uk

AUSTRALI

Head Office &

Manufacturing Plant

Tasman Sinkware Pty Ltd

Regency Park SA

Phone: +61 8 8348 6444

Fax: +61 8 8348 6495

Email: sinkware@tasbuildpro.com.au

ASIA PACIFIC DISTRIBUTORS

New Zealand - Dux Industries

Ltd

Phone: 0800 367 389

Singapore - Sim Siang Choon

Phone: 6266 6632

Hong Kong - Deacon & Co Ltd

Phone: 2369 6111 Any advice, recommendation, information, assistance or service provided by Tasman Sinkware in

relation to goods manufactured by it or their use and installation, is given in good faith and is believed by

Tasman Sinkware to be appropriate and reliable. However, any advice, recommendation, information,

assistance or service is provided by Tasman Sinkware without responsibility or liability.

SPECIAL INSTRUCTIONS FOR PARTICULAR TOP MOUNT SINK MODELS

CAUTION

Leave protective tape on the sink when inverting over a benchtop and tracing its shape.

The polished stainless steel will scratch if the sink slides across a hard surface.

AU Top Mount Installation Instructions

TF 08d.doc

Tasman Sinkware

is a division of

Fletcher Building

TEMPLATE *

A number of Oliveri sinks require a non-standard shape hole (not a rectangle

or circle). Locate the template included in (or printed on) the packaging and

place in the correct position on the counter/benchtop. Compare the template

to the sink to check it is correct. Some sink templates apply to both left-hand

and right-hand model sinks. Ensure the template is the correct way around

for your model sink. (If no template is available, carefully invert the sink over

the counter/benchtop and trace around it.)

CHECK SPACE & LEVEL

Use a level to check the counter/benchtop – if not level, have rectified.

Ensure there is adequate space for tapware (including a splash back if

specified). Check space for installation (underneath) and operation (above).

Particular care must be taken when a thick splash back is used (it may

interfere with tapware location and operation). Ensure the cabinet will not

foul the sink mounting flange or basins.

MARK CUT OUT *

Carefully mark around the cardboard template (or follow drawing instructions).

Once the hole is marked out, use the template to conduct a final check before

cutting. Note: The template is the exact finished cut-out size required.

IMPORTANT

If you have traced the sink itself to mark your cut out, the hole must be

cut 10mm inside the marked line.

CUT & FINISH HOLE *

Re-check the position and cut out shape you have traced before cutting.

Ensure there are no obstacles below that might interfere with cutting.

Drill pilot holes to accept an appropriate cutting tool for the counter/benchtop

material (wear suitable personal protection equipment). Cut just inside the

template mark (or 10mm inside the sink tracing).

TRIAL FIT THE SINK

Check that all clips are folded in so they will adequately clear the cut-out.

Carefully position the sink into the cut-out to make sure it fits correctly.

If the fit is not correct, remove the sink and proceed with remedial work.

Perform another trial fit after corrections have been made.

MASKING

If using a sealant, masking is necessary to prevent sealant overrun.

It is recommended that the edge of the sink and the edge of the cutout are

both covered with a suitable masking tape.

This tape should be removed within 2 days of application.

CHECK FOAM SEAL

Make sure the foam seal is intact and fits all the way around the sink with no

gaps visible. This will ensure a watertight seal when the sink is properly

tightened down to the counter/benchtop.

ADDITIONAL SEALANT

Apply additional sealant / caulking compound around the join where the

counter/benchtop and the stainless steel sink meet. Check that the caulking

product is mildew resistant and is suitable for use on the counter/benchtop

material and also is suitable for use on stainless steel. Clean away any

excess before it dries. Note: Additional sealant should always be used if gaps

are apparent after the sink has been clamped to the counter/benchtop.

PLUMBING & TAPWARE

IMPORTANT - Connections to plumbing should always be done by a

licensed plumber. Fit supplied basket wastes to sink bowls. Some models do

not include basket wastes for every bowl. Install tapware according to

manufacturer’s instructions.

Care should be taken when fitting wastes to the sink. Follow the instructions

provided with the wastes.

INSTRUCTIONS CONTINUE OVER PAGE

It is essential that the installation is waterproof and carried out in accordance with these instructions.

Tasman Sinkware will not be held responsible for any damage caused by leakage or faulty installation.

CARE INSTRUCTIONS FOR YOUR OLIVERI STAINLESS STEEL SINK

AVOID CONTACT WITH ROUGH OR DIRTY SURFACES as new polished stainless steel will show scratches!

DO’s

• • Clean with soap & water (towel dry) Clean along the grain of the Stainless Steel

• Use a soft brush or sponge (old tooth brush) Wipe over with a glass cleaner •(Windex is very good)

• Polish with a metal polish paste (Autosol / Brasso) • Use a Liquid cleaner (Bon-Ami or Jiff)

• Use a granulated stainless steel cleaner (Essteele)

DO NOT’s

• NEVER use Steel wool

• Beware of harsh liquid cleaners

• Beware of grit within cloths and mineral deposits within water

• Avoid prolonged exposure to acids from Fruit, Fruit juices, Salts, Spirits, Bleach, Tea-bags

• Avoid prolonged contact with ordinary steel which can rust Tin Cans, Steelwool

• Do not keep harsh (acids or chlorine) chemicals under sink / laundry tub

• Do not leave chlorine/chloride chemicals on stainless steel surface

• Do not leave liquid soaps & cleaners to dry on stainless steel

• Do not use bleaches (White King, Domestos, Clorox)

FITTING THE SINK

If you choose to mount the tap / faucet onto the sink prior to fitting, take extra

care as it will change the weight and balance of the sink. Position and align

the sink correctly in the cutout and lower it onto the counter/benchtop. From

underneath, tighten the clips with a screwdriver (follow the sequence marked

on the template) until the sink is secure and no gaps are visible. Take extra

care if usin

power tools as ove

-ti

htenin

can dama

e clips.

FINAL CHECK OF FOAM SEAL

With the sink tightened down. Visually confirm the foam seal is not protruding

anywhere underneath. If it does, undo all the clips, reposition the foam seal

and tighten down again. If the foam seal has been damaged, replace the

damaged section. If the tap/faucet was mounted prior to fitting – check that

the position is correct.

Produktspecifikationer

Varumärke:	Oliveri
Kategori:	Sjunka
Modell:	PR1131
Färg på produkten:	Zilver
Vikt:	75 g
Bredd:	110 mm
Djup:	210 mm
Höjd:	120 mm
Förpackningens bredd:	31 mm
Djuppackning:	175 mm
Förpackningshöjd:	144 mm
Anslutningsteknik:	Bedraad
Kompatibla operativsystem:	Windows 2000/XP/2003/Vista (x32, x64), \nLinux Kernel 2.6.11, \nMAC 10.4
Mac-kompatibilitet:	Ja
Värdgränssnitt:	PCIe
Anslutning(ar):	DB9
Förpackningens längd:	175.00 mm
Chipset:	MosChip MCS9901
Överföringshastighet:	0.4608 Mbit/s
Antal portar:	4
Utgångsgränssnitt:	RS-232