Pioneer CP-4EX Bruksanvisning
Pioneer
högtalarstöd
CP-4EX
Läs nedan 📖 manual på svenska för Pioneer CP-4EX (32 sidor) i kategorin högtalarstöd. Denna guide var användbar för 6 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare
Sida 1/32
http://www.pioneer.co.uk
(or http://www.pioneer.eu)
2
En
Thank you for buying this Pioneer product. This speaker stand
should only be used with the S-4EX Pioneer speaker system.
Please read through these operating instructions for proper
assembly and use. After you have finished reading the
instructions, put them away in a safe place for future reference.
Before you start
Before setting up your speaker system, we recommend reading
the operating instructions for your system thoroughly.
• Do not use this speaker stand with speakers other than the
Pioneer S-4EX, since the product balance may be impaired,
resulting in tipping or dangerous falls.
• Only use the screws supplied when fixing the speaker to the
speaker stand.
• Do not place the stand on an unstable and/or sloping surface.
The stand and speaker may fall and cause injury.
• Do not use with any speaker system other than the one for
which the unit was designed. The stand may collapse and be
damaged and/or the speaker may fall and cause injury.
• When moving the speaker and stand, first remove the speaker
from the stand, and then move the stand, holding it by the
stems.
• Place the stand on a stable, level surface; placing the stand on
an unstable surface can be dangerous.
• Pioneer assumes no liability whatsoever for damages
resulting from assembly, improper mounting, insufficient
reinforcement, misuse of the product, acts of nature, etc.
Names of Parts
Attaching speakers to the
stands
A medium Phillips screwdriver is required for attaching the
speakers.
Assembly with the S-4EX speaker
system
If you are using the S-4EX speaker system, note that there is a
fastening nut provided on the speaker base (see below).
When installing spikes on speaker
Use only spikes supplied with S-4EX.
1 Set spikes into three locations on bottom of speaker.
Consult the S-4EX operating instructions for additional
instructions.
2 Apply the furnished cork plates on the three locations on
the speaker support.
3 Rest the speaker gently on the speaker support while
aligning the spikes with the cork plates on the top of the
speaker support, then fix in placing using the washers,
spring washers, and screws (bind head M5 x L55).
S eake su o tp r pp r
Stand stems
Stand base
Screw holes
fo secu eaker ring sp r
Non-skid
co adsrk p
S eakep r
su o tpp r
Co latesrk p
[SEC2255]
55 mm
Black
S eake basep r
S eakep r
su o tpp r
Sc ew holesr
fo secu ingr r
s eakep r
Fastening nut
Washer
[SBE6006]
S ing washepr r
[SBE6005]
Screws
(Bind head, M5 x L55)
[SBA1307]
Co latesrk p
3
En
English
When mounting spikes on speaker stand
Use only spikes, spike bases, and auxiliary feet provided with
the S-4EX.
1 Install spikes in three locations on the bottom of the
stand base plate, then install the two auxiliary feet to
prevent rocking.
2 Place spike bases on the floor in the position where the
spikes will rest.
3 Rotate the spikes to adjust the height, then rotate the
spike nuts counterclockwise to lock the height of the spike.
4 Rest the speaker stand on the spike bases and check to
confirm the stand is stable without any rocking.
5 Rotate the auxiliary feet to adjust height.
Adjust the height so that about 1 mm to 2 mm of space
remains open between the feet and the installation surface.
6 Rotate the nuts counterclockwise to lock the height.
7 Rest the speaker on the top of the stand and use washers,
spring washers and screws (bind head M5 x L55) to fasten
the speaker securely to the stand.
• When installing spikes, lay the speaker stands on their sides
on a soft blanket or surface to prevent scaring.
• Set the spike bases with the concave side upward to receive
the spike as shown below.
• When the spikes are used alone without spike bases,
scratches may be cuased to the floor or other installation
surface. Always use the spike bases when using spikes.
Other Information
Stand maintenance
• Use a polishing cloth or dry cloth to wipe off dust and dirt.
• If the stand is very dirty, use a soft cloth dipped in some neutral
cleanser diluted five or six times with water. Finally, wipe again
using a dry cloth. Do not use furniture wax or cleaners.
• Never use thinners, benzine, insecticide sprays and other
chemicals on or near the stand, since these will corrode the
surfaces.
Specifications
External dimensions. . . . . . . 360 (W) mm x 570 (H) mm x 485 (D) mm
14 3/16 (W) in. x 22 1/2 (H) in. x 19 1/8 (D) in.
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.9 kg (30 lb 11 oz.)
Supplied accessories
Screws (Bind head, M5 x L55) [SBA1307] . . . . . . . . . . . . . . . . . . . . . . 2
Spring washers [SBE6005] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Washers [SBE6006] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Cork plates [SEC2255] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
These operating instructions [SRD6100]
• Specifications and design subject to possible modification
without notice, due to improvements.
• The product number are listed above in square brackets.
S ikep
S ike nutp
Stand base plate
Auxilia y feetr
55 mm
Black
S eake basep r
S eakep r
su o tpp r
Sc ew holesr
fo secu ing s eaker r p r
Fastening nut
Washer
[SBE6006]
S ing washepr r
[SBE6005]
Sc ewsr
(Bind head, M5xL55)
[SBA1307]
Replacement part numbers
Part name
• Protector (Bottom)
• Protector (Top)
• Packing case
• Protection sheet
Part no.
SHA2632
SHA2631
SHH1324
SHC1879
Published by Pioneer Corporation.
Copyright © 2008 Pioneer Corporation.
All rights reserved.
Produktspecifikationer
| Varumärke: | Pioneer |
| Kategori: | högtalarstöd |
| Modell: | CP-4EX |
Behöver du hjälp?
Om du behöver hjälp med Pioneer CP-4EX ställ en fråga nedan och andra användare kommer att svara dig
högtalarstöd Pioneer Manualer
4 Oktober 2024
högtalarstöd Manualer
- högtalarstöd Philips
- högtalarstöd JBL
- högtalarstöd Nedis
- högtalarstöd Audizio
- högtalarstöd Bowers And Wilkins
- högtalarstöd Toa
- högtalarstöd Hama
- högtalarstöd Sennheiser
- högtalarstöd Techly
- högtalarstöd Bogen
- högtalarstöd Bose
- högtalarstöd Teufel
- högtalarstöd Pro-Ject
- högtalarstöd Adj
- högtalarstöd Neumann
- högtalarstöd Sanus
- högtalarstöd Vogels
- högtalarstöd Electro-Voice
- högtalarstöd Valcom
- högtalarstöd One For All
- högtalarstöd Omnitronic
- högtalarstöd Newstar
- högtalarstöd Cambridge
- högtalarstöd Ultimate
- högtalarstöd Peerless
- högtalarstöd Dynaudio
- högtalarstöd Chief
- högtalarstöd Crestron
- högtalarstöd Monacor
- högtalarstöd Sanus Systems
- högtalarstöd Heckler Design
- högtalarstöd Bell'O
- högtalarstöd Extron
- högtalarstöd B-tech
- högtalarstöd Gravity
- högtalarstöd Kanto
- högtalarstöd Vivolink
- högtalarstöd Multibrackets
- högtalarstöd Triangle
- högtalarstöd Adam Hall
- högtalarstöd Norstone
- högtalarstöd Roadworx
- högtalarstöd My Wall
- högtalarstöd Xtech
Nyaste högtalarstöd Manualer
3 Oktober 2024
30 September 2024
27 September 2024
26 September 2024
26 September 2024
26 September 2024
26 September 2024
26 September 2024
26 September 2024
26 September 2024