Samlex BS 140 DUAL Bruksanvisning

Samlex Batteriladdare BS 140 DUAL

Läs nedan 📖 manual på svenska för Samlex BS 140 DUAL (2 sidor) i kategorin Batteriladdare. Denna guide var användbar för 9 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF
Sida 1/2
www.samlex.com
www.samlex-solar.com
BS 100 DUAL
BS 140 DUAL
Model No.
BATTERY SEPARATOR
OWNER’S MANUAL / GEBRUIKSAANWIJZING
Please read this manual before operating your separator
Intelligent Battery Separator
Installation and user’s manual
Description:
The BS microprocessor controlled battery separator
is used in multi-batteries systems like on boats,
caravans and campers. It supervises the primary
battery state of charge and therefore avoids starting
problems. The BS can also be used as a voltage
dependent switch.
The working principle is the following: the BS lets the
primary battery being recharged by the alternator until
a voltage of 13.2V (26.4V) during at least 7 seconds is
reached. Then the two batteries are put in parallel by
the contact of the relay. The secondary users are
normally connected to the auxiliary battery. The relay
opens when the batteries voltage reaches 12.8V
(25.6V) during at least 60 seconds. This way the
starter battery remains charged.
If a battery charger is connected to the auxiliary battery
and this battery reaches a voltage of 13.2V (26.4V)
during at least 7 seconds, the relay closes and
charges at the same time the starter battery. This is an
advantage if the vehicle remains stationary over a long
period of time.
If the battery charger is disconnected and the battery
voltage reaches 12.8V (25.6V) during at least 60
seconds, then the BS separates again the two
batteries.
Start assistance:
The BS has an additional connection enabling an assis-
tance to the starting. If the connection 85 (BS 100) or
86 (BS 140) is connected to the starter contact, the BS
contact closes and this way the 2 batteries contribute to
the engine start.
Cautious when this function is used very high currents
may go through the relay contact by the start of big
engines. These high currents may damage the contact
of the BS if they exceed its nominal current.
Voltage dependent switch:
In some cases it is needed to have a powerful DC
source supply but only when the engine is running.
The BS allows also this kind of installations. It is
sufficient to simply connect the primary battery to the
connection 30, the system earth to the connection 86
(BS 100) or 85 (BS 140) and the positive of the equipment
to supply to the connection 87. When the engine runs a
voltage of 13,2V (26,4V) during at least 7 seconds is reached,
the equipment is then powered thru the contact of the BS.
Protection against overvoltages:
The BS has also a function enabling to protect the
battery and the appliances that are connected to it
against an overvoltage generated, for instance, by a
defectuous alternator. As soon as a voltage higher
than 16 V (32V) is detected, the contact of the BS
opens immediately.
Installation:
To implement the function « start assistance », a fuse
protected connection has to be carried out between
the connection 85 (BS 100) or 86 (BS 140) and the contact
o f t h e s t a r t e r c o n t a c t .
A short-circuit between the positive and negative
of the batteries can damage your system. Make
sure that the connections are properly done!
Technical specifications:
Supply: Automatic detection 12/24 V
Max. current: 100 A (BS 100) or 140 A (BS 140)
Battery connection: M6
Other connections: Faston 6,3 mm
Cable cross section: 25mm2
Consumption OFF: 12V=1.5mA / 24V=1.5mA
Consumption ON: 13.5V=360mA / 27V=160mA
Minimum chargetime: 60 seconds
Fast opening: < 11.8V (12V) / 23.6 (24V)
after 4 seconds
Connections:
30 Positive terminal of the primary battery (starter
battery)
85 Ignition switch (only if « start assistance » is
needed)
86 Negative terminal (Cautious this connection
must always remain connected via a fuse of 3A)
87 Positive terminal of the auxiliary battery (If the
function « voltage dependent switch » is
needed, connect the equipment positive here)
86 for BS 140
85 for BS 140
+12Vdc(+24Vdc)
External
Charger
Alternator
Primary
Battery
Auxiliary
Battery
To the starter contact
(optional, see installation)
BS
85
or
86
86 or 85
30
87
Caution!
The fuses must be
dimensioned accordingly
to the cables cross-
sections!
+12Vdc(+24Vdc)
External
Charger
Alternator
Primary
Battery
Auxiliary
Battery
To the starter contact
(optional, see installation)
BS
85
or
86
86 or 85
30
87
Caution!
The fuses must be
dimensioned accordingly
to the cables cross-
sections!
via een zekering van 3A
86 voor BS 140
85 voor BS 140

Produktspecifikationer

Varumärke: Samlex
Kategori: Batteriladdare
Modell: BS 140 DUAL

Behöver du hjälp?

Om du behöver hjälp med Samlex BS 140 DUAL ställ en fråga nedan och andra användare kommer att svara dig


Batteriladdare Samlex Manualer

Samlex

Samlex EVO-1224F Bruksanvisning

11 September 2024
Samlex

Samlex SEC-1250UL Bruksanvisning

11 September 2024
Samlex

Samlex ACR-160 Bruksanvisning

11 September 2024
Samlex

Samlex SEC-2425UL Bruksanvisning

11 September 2024
Samlex

Samlex SEC-1215UL Bruksanvisning

11 September 2024
Samlex

Samlex SEC-1230UL Bruksanvisning

11 September 2024
Samlex

Samlex BS 140 DUAL Bruksanvisning

25 Augusti 2024

Batteriladdare Manualer

Nyaste Batteriladdare Manualer

Nitecore

Nitecore UHX1 PRO Bruksanvisning

27 Oktober 2024
Nitecore

Nitecore EMR05 TAC Bruksanvisning

26 Oktober 2024
Xblitz

Xblitz XC1 Bruksanvisning

25 Oktober 2024
Bosch

Bosch GAA12V-21N Bruksanvisning

24 Oktober 2024
Panasonic

Panasonic CF-VCB331 Bruksanvisning

24 Oktober 2024
Ryobi

Ryobi One+ RC18627 Bruksanvisning

21 Oktober 2024
Alecto

Alecto BL-179 Bruksanvisning

19 Oktober 2024
Tronic

Tronic KH 971 Bruksanvisning

18 Oktober 2024
Graupner

Graupner Ultramat 12 Bruksanvisning

17 Oktober 2024
Graupner

Graupner ULTRA DUO PLUS 30 Bruksanvisning

16 Oktober 2024