Sjoef Classic BIS20M1 Bruksanvisning
Läs nedan 📖 manual på svenska för Sjoef Classic BIS20M1 (14 sidor) i kategorin Cykel. Denna guide var användbar för 7 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare
Sida 1/14
1
Instrucons Manual
keep this manual
Handbuch
Bewahren Sie dieses Handbuch
Handleiding
Bewaar deze handleiding
S J O E F
Amsterdam
Made in China
in China hergestellt
Gemaakt in China
Bisshops BV
Herengracht 338
1016 CG Amsterdam
The Netherlands
2
EN - Manual
This manual provides instrucons for assembling and maintaining your new SJOEF
bicycle. Before assembling the bicycle, it is important to follow these steps.
• Remove the bicycle from the packaging and place all the parts together. Be
careful not to leave any parts inside the packaging.
• Check that all parts are present
• Assembly is intended for adults only
Tip: Are you having trouble with the assembly? Then please contact our customer
service.
The bicycles are manufactured to comply with European standards EN ISO-
8098:2014 or EN ISO-4210:2014. Please note: the manufacturer is not responsi-
ble for improper use or incorrect assembly of the bicycle.
Assembly
The bicycle can be assembled in a few simple steps. It is important to follow the
order of the instrucons in order to make the assembly as easy as possible.
Installaon of the saddle
1. Insert the saddle pillar into the seatpost.
2. Adjust the saddle to the correct height. Observe the safety mark on the
saddle pillar, which should disappear into the frame. The saddle is at the right
height when your toes touch the ground while standing sll. If possible, the
saddle should be adjusted so that the enre foot is on the ground.
3. Is the saddle at the right height? Lock the saddle by ghtening the saddle
bolt.
Installing the handlebar and stem (if required)
1. Insert the stem (including handbrake lever and bell if present) into the frame.
2. Observe the safety marking on the stem, it should disappear into the frame.
3. Posion the handlebar at the desired height and check whether it is perpen-
dicular to the front wheel.
4. Tighten the handlebar clamp and/or bolt.
Installing the pedals
PLEASE NOTE: there is an (L) on the le and an (R) on the right side of the pedal.
Incorrectly ghtening the pedal will render the bike unusable and will void the
warranty.
3
1. It is advisable to grease the ends of the pedals so that they can be replaced
easily in the future.
2. An L or R can be read o from the axle of the pedal. Use this to check which
pedal should be ed on the le and which on the right. Are there no L or R
on the pedals? Then the le pedal contains a marking in the form of a line.
3. Insert the right pedal into the crank and turn the pedal clockwise by hand
towards the front wheel. It should be easy to turn the pedal; if it is s, the
thread may be damaged.
4. Then turn the le pedal by hand counter-clockwise into the crank, also in the
direcon of the front wheel.
5. Finally, ghten the pedals even further using an open-end spanner.
Checking the cranksha nut
There are a number of bicycles in which the le-hand crank is secured with a
crank nut. Before using the bike, check that this nut is properly ghtened:
1. First ghten the nut with the 6 sides (clockwise).
2. Then ghten the lock nut (3 notches).
Fing the side wheels (if available)
1. Fit the support wheel arm on the rear axle against the locking plate which is
already ed on the rear axle). Alternavely, if present, secure the addional
plate on the rear frame with 2 screws.
2. Make sure that everything is rmly aached to the rear axle.
3. The quick release and protecon plate (if applicable) should only be slid onto
the rear wheel axle.
4. Screw the outer axle nut ght when the desired height of the side wheels has
been found. The side wheels should stay about 6 mm above the ground on
both sides.
Fing the front wheel (if necessary)
1. Posion the front wheel in the middle of the front fork.
2. Subsequently, ghten the nuts alternately while keeping the front wheel
straight in the middle of the front fork.
Installing the front mudguard (if required)
1. Unscrew the nuts with washers from the screw bolt.
2. Insert the screw bolt through the hole in the front frame/fork (make sure that
one ring remains at the front).
3. Fit the front reector or headlight (if any) between the ring and the front
end of the bolt. Ensure that the front reector (or front light) remains in the
correct posion by holding it with one hand.
4. If not already in place, push the hook hanging from the mudguard upwards.
Place the hook at the back of the hole in the frame/fork on the bolt.
5. Next, place the washer and nally ghten the nut.
6. Check whether the front reector (or lighng) is upright. You can then ghten
the nut rmly.
Produktspecifikationer
| Varumärke: | Sjoef |
| Kategori: | Cykel |
| Modell: | Classic BIS20M1 |
Behöver du hjälp?
Om du behöver hjälp med Sjoef Classic BIS20M1 ställ en fråga nedan och andra användare kommer att svara dig
Cykel Sjoef Manualer
4 September 2024
3 September 2024
Cykel Manualer
- Cykel Bosch
- Cykel Altec
- Cykel BH Fitness
- Cykel Crivit
- Cykel Huffy
- Cykel Batavus
- Cykel Suzuki
- Cykel Giant
- Cykel Redline
- Cykel Gazelle
- Cykel Ideal
- Cykel Biltema
- Cykel Geuther
- Cykel Kent
- Cykel Sigma
- Cykel Kayoba
- Cykel Octane
- Cykel Honda
- Cykel Baninni
- Cykel Urban Arrow
- Cykel Amigo
- Cykel Lionelo
- Cykel Kawasaki
- Cykel Qwic
- Cykel Puky
- Cykel Scott
- Cykel Ducati
- Cykel Babboe
- Cykel Tern
- Cykel Cannondale
- Cykel Schwinn
- Cykel Trek
- Cykel Porsche
- Cykel Valk
- Cykel Puch
- Cykel Montego
- Cykel Monty
- Cykel Monster
- Cykel Eufab
- Cykel Winora
- Cykel LACROS
- Cykel Dahon
- Cykel Veloretti
- Cykel Kixi Razor
- Cykel Raleigh
- Cykel Sensa
- Cykel Koga
- Cykel Crown
- Cykel Pazzaz
- Cykel VANMOOF
- Cykel Devron
- Cykel Inmotion
- Cykel Kindercraft
- Cykel Mongoose
- Cykel Little Nation
- Cykel Sun Baby
- Cykel Hase
Nyaste Cykel Manualer
20 Oktober 2024
16 Oktober 2024
16 Oktober 2024
16 Oktober 2024
16 Oktober 2024
16 Oktober 2024
12 Oktober 2024
11 Oktober 2024
9 Oktober 2024
7 Oktober 2024