Sonneman Nebula 2067.25 Bruksanvisning

Sonneman Lampa Nebula 2067.25

Läs nedan 📖 manual på svenska för Sonneman Nebula 2067.25 (9 sidor) i kategorin Lampa. Denna guide var användbar för 6 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Sida 1/9
June 16, 2020
©2020 SONNEMAN - A WAY OF LIGHT 1 of 8
LED Product Information and Warnings
Important
Always disconnect the power before installing or replacing parts and before cleaning or other maintenance.
Consult a qualied, licensed electrician to ensure correct branch circuit conductor.
Please read all included assembly instructions and warnings carefully before installation. Contact
Customer Service if you have any questions or concerns. Before installation, please conrm that the xture
is compatible with your supply voltage and dimming system, if present.
LEDs are highly sensitive electronic devices, and must be treated with care. Do not open any factory
sealed compartments, and avoid touching the LEDs with your hands or any object.
Although all our xtures are equipped with protective devices, LED xtures are vulnerable to power surges
and supply variations. Do not install LED xtures on the same circuit as any motors, appliances, or HVAC
systems.
Do not remove or bypass any LED Driver or Transformer that is provided with the xture, and do not
replace or substitute with another power supply.
Remote LED Driver or Transformer installation must be done by a licensed electrician and in accordance
with local codes. Remote installations should be in an accessible location, as close to the xture as possible.
Fixtures must be wired in parallel on independent leads; do not "daisy chain" multiple xtures together or
wire them in series.
All factory-made splices and connections must remain intact. LED circuits are carefully designed and built,
and improper connections may damage the xture.
The ends of coaxial pendant cords have been precisely stripped and split at the factory and must not be
eld cut. Excess cord or cable should be neatly coiled and reserved in the xture canopy.
Any mounting hardware is provided for your convenience and should be used with discretion. Always use
the appropriate hardware for the mounting surface.
June 16, 2020
©2020 SONNEMAN - A WAY OF LIGHT 2 of 8
Assembly Instructions
INSTRUCTIONS D’INSTALLATION
Important
Always disconnect the power before installing or replacing parts and before cleaning or other maintenance.
Consult a qualied, licensed electrician to ensure correct branch circuit conductor.
Consulter un électricien qualié pour vous assurer que les conducteurs de la dérivation sont adéquats.
1. Shut o power to the outlet box (A).
2. Attach the mounting plate (B) to ceiling using slots and wood screws (C). CAUTION: Fixture must be supported
independent of outlet box. Customer is responsible for ensuring appropriate ceiling construction to support the
weight of the xture.
3. Assemble xture frame (T) according to the Frame Assembly instructions on Page 3.
4. Determine the height at which the xture (T) is to be hung. Install the mounting brackets (P) to the ceiling with
anchors (Q) and screws (R), then screw the posts (S) onto the mounting brackets. Insert cables (B) into posts and adjust to
level the xture: to shorten, push the cable up; to lengthen, push in the plunger while pulling down on the cable, release
the plunger to lock. Support frame using sawhorses (or equivalent) while mounting and leveling.Suggestion:
5. Insert two power cords (D) through corresponding holes in canopy (E).
6. Use the screwdriver (G) to loosen the slotted set screws (H) in the two
cord posts (J). Insert the cords and adjust to the desired length.
Note: Cords must not support xture weight.
Tighten the set screws to set. Reserve extra cord in canopy (E).
7. Make appropriate electrical connections using wire nuts (Appendix A):
a. Connect the two LED driver (U) live wires (black) to the
outlet box live wire.
b. Connect the two LED driver (U) neutral wires (white) to
the outlet box neutral wire.
c. Connect the ground wire (green or uncoated) to the
outlet box ground wire. If no ground is present in outlet
box, connect ground wire to
the mounting plate (B) using
the green screw (included).
d. For each cord, connect the
cord inner conductor to one
of the driver positive (+)
output wire and connect the
cord outer conductor to the
driver negative (-) output wire.
Repeat for the second cord
and second driver.
8. Attach canopy (E) to the
mounting plate (B),
secure with canopy nut (V).
9. Install Cluster Arms and attach
globes (K1, K2, K3) as shown
on pages 4-7.
10. Restore power to
the outlet box (A).
Note
This xture is dimmable with Electronic Low Voltage (Trailing-Edge), Incandescent (Leading-Edge), and 0-10V type
dimmers only.
Care Instructions
Dusting: Use a clean, dry cloth.
Cleaning: To protect the nish, avoid any harsh abrasives or chemicals.
2067
June 16, 2020
©2020 SONNEMAN - A WAY OF LIGHT 3 of 8
Bar Assembly (Fig. A):
1. Insert Bracket plug into corresponding Bar plug.
2. Slide Bar over Bracket and secure with (2) countersunk screws.
Frame Assembly (Fig. B):
1. Connect Bar B and Bar C to Bar A. Refer to Bar Assembly above.
Fig. B
Top View

Produktspecifikationer

Varumärke: Sonneman
Kategori: Lampa
Modell: Nebula 2067.25

Behöver du hjälp?

Om du behöver hjälp med Sonneman Nebula 2067.25 ställ en fråga nedan och andra användare kommer att svara dig




Lampa Sonneman Manualer

Lampa Manualer

Nyaste Lampa Manualer