Teledex Opal 1003 Bruksanvisning

Teledex Telefon Opal 1003

Läs nedan 📖 manual på svenska för Teledex Opal 1003 (7 sidor) i kategorin Telefon. Denna guide var användbar för 4 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF

Sida 1/7

OWNER’S

MANUAL

OPAL 1003

1005

1010

The Teledex one-line

telephones specifically

designed for the international

hospitality industry.

INCLUDED IN YOUR PACKAGE

Handset

Base Unit

Coiled Handset Cord

Line Cord

Clear Plastic Overlay

User Guide

CONNECTING THE OPAL TELEPHONE

1. Located on the left side of the Opal (as the phone is facing you) is a modular jack. Insert one end of the coiled

handset cord into this jack (you should hear the coil cord click when properly inserted).

2. Insert the other end of the coiled handset cord into the modular jack on the handset.

3. Turn the telephone so the back panel is facing you. Insert either end of the line cord into the jack on the back of

the telephone labeled LINE.

4. Insert the other end of the line cord into a telephone wall outlet jack.

5. Once your telephone is connected, remove the plastic overlay and place the paper faceplate over the keys.

Replace the plastic overlay by hooking the tabs on the overlay into the recessed slots located on both sides. The

overlay is easiest to insert when; the left or right side tabs are inserted first, and the middle of the overlay is

slightly bowed to allow for insertion of the other tabs.

PLACING A CALL

1. Lift the handset.

2. Listen for dial tone. Dial the desired number, or press an AUTO DIAL key to automatically dial a number.

3. To end the call, hang up by placing the handset back in the cradle.

RECEIVING A CALL

An audible ring and flickering red message waiting light will indicate an inbound call.

1. Lift the handset. The Opal will engage the ringing line.

2. To end the call hang up the handset.

ADJUSTING THE RING VOLUME

Locate the adjustment control on the back of the telephone labeled RINGER LOW/HI. Slide the switch to the

desired LOW or HI ring volume.

REDIAL

TO REDIAL THE LAST TELEPHONE NUMBER DIALED:

1. Lift the handset from the cradle.

2. Press the REDIAL key.

ADJUSTING THE HANDSET VOLUME

The HANDSET VOLUME key has three levels. When the handset is first lifted, the handset volume is NORMAL.

Locate the HANDSET VOLUME key below the keypad. Press the key once and the volume level will increase

one level (to MEDIUM volume). Press the key once more and the volume level will increase an additional level

(to HIGH volume). To return the handset volume to NORMAL , press the handset volume key again.

The handset volume will always return to NORMAL when the handset is replaced in the cradle.

FLASH KEY

Pressing the FLASH key initiates a 600ms hookflash. Typical usage is to access PBX features like call waiting.

AUTO DIAL KEYS

The Opal has programmable AUTO DIAL keys. These keys can be programmed to automatically dial telephone

numbers, or activate telephone system features.

PROGRAMMING AUTO DIAL KEYS:

The telephone must be connected to a telephone line.

1. Lift the handset from the cradle.

2. Press the recessed STORE key and release it. (Please see diagram on the next page).

3. Enter the telephone number including PAUSE* as required. The sequence can be up to 15 digits.

4. Press the AUTO DIAL key where the number is to be stored.

5. Place the handset back in the cradle.

*A 3.6 second pause is entered in a dialing sequence by pressing the REDIAL key for each PAUSE required.

CONVERTING FROM DESK TO WALL MOUNT

The Opal Telephone can be changed for wall mounting applications. The conversion is easiest when the handset

and line cords are not connected.

1. Located on the top of the telephone above the speaker grill is the wall/desk mount clip. Remove this clip by

firmly pushing upward (towards the hookswitch).

2. Flip the clip over (top to bottom) so that the protruding edge is towards the top of the phone. This edge will

hold the handset.

3. Turn the Opal over so the bottom is up facing you. Place the Opal on a nonabrasive surface to prevent scratch-

ing.

4. Locate and remove the mounting bracket, firmly push back and pull up to remove two of the four retaining tabs.

5. Rotate the mounting bracket 180 degrees clockwise so that the mounting eyelet on the bracket is facing in the

same direction as the other mounting eyelet located on the bottom of the telephone.

6. Insert the top two retaining tabs of the mounting brackets into the mounting bracket slots (located near the

middle of the telephone). Then firmly push down to insert the retaining tabs on the opposite side of the mounting

bracket.

7. Connect a short modular line cord into the jack on the back of the phone (labeled LINE). Route the line cord

thought the line cord channel. Connect the other end of line cord to the phone jack on the wall mounting plate.

8. Turn the telephone over, and slide the Opal down onto the mounting posts in downward direction. Both eyelets

should line up with the mounting posts.

9. Complete the wall mounting by installing the handset and handset cord.

Produktspecifikationer

Varumärke:	Teledex
Kategori:	Telefon
Modell:	Opal 1003
Enhetsplacering:	Vrijstaand
Typ av operation:	Buttons, Rotary
Färg på produkten:	Wit
Inbyggd display:	Ja
Värmekälla:	Electrisch
Bredd:	600 mm
Djup:	540 mm
Höjd:	850 mm
Nettoskatt:	2800 W
Typ av laddare:	Voorbelading
Torksystem:	Condensatie
Torkningsklass:	A
Cykelns längd:	124 min
Ljudnivå:	65 dB
Energie-efficiëntieklasse:	B
Energie consumptie:	4.29 kWu
Årlig-energiförbrukning:	504 kWu
Strömförbrukning (i standby):	0.41 W
Strömförbrukning (när avstängd):	0.41 W
Nominell kapacitet:	7 kg
Type beeldscherm:	LCD