Vemer PR-1DA Bruksanvisning

Vemer Inte kategoriserad PR-1DA

Läs nedan 📖 manual på svenska för Vemer PR-1DA (26 sidor) i kategorin Inte kategoriserad. Denna guide var användbar för 9 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF

Sida 1/26

- 27 -

User Manual Regulators

English

Contents

■Safety warnings Page 28

■Technical specifications Page 28

■Description of instrument Page 31

■Electrical connections Page 31

■Glossary Page 32

■Operation Page 37

■Setting the regulation parameters Page 37

■Parameter menu Page 39

■Error messages Page 46

■Reference standards Page 47

■Dimensions and connection diagrams, 33x75 mm Page 48-49

■Dimensions and connection diagrams, 72x72 mm Page 50

■Dimensions and connection diagrams, 4-DIN Page 51

- 28 -

User Manual Regulators

English

■ During the installation and operation of the instrument, follow the

instructions set out below:

1) The instrument should be installed by a skilled operator.

2) Strictly follow the connection diagrams when installing the instrument.

3) Do not power or connect the instrument if any part of it is damaged.

4) Before touching the terminals, make sure the wires to be connected to

the instrument are not live.

5) The connection cables should be able to resist the maximum operating

temperature (Tmax), obtained from the sum of the maximum ambient

temperature (Ta) + a temperature of 20 °C (Tmax= Ta + 20 °C).

6) The instruments guarantee a main insulation between the low voltage

(250 V) and very low voltage parts.

7) Any outside switches connected to the controls should guarantee a

minimum insulation at operating temperature of 250 V AC, or should be

protected by equivalent insulation.

8) Contacts: all type 1C (CEI 107-70 and variants).

9) The instruments require no maintenance.

■Series of digital regulators used for the most simple requirements in the control

and regulation of humidity and pressure levels in air conditioning, heating

and refrigeration systems

■Two dedicated base models for pressure and humidity control:

- DIGITAL HUMIDITY REGULATORS HR

- DIGITAL PRESSURE REGULATORS PR

■Each single model has 1 probe input for the connection of active sensors

with standardised 0÷20 mA, 4÷20 mA and 0÷1 V outputs

■The power supply to the active probe (linear sensor) comes directly from

the instrument: 9 V DC available

• For each single model, the probe input can be configured from the keyboard

• Available in versions with 1 or 2 relay outputs with contact in exchange

• Regulators with 3 digit, seven segment and decimal point display

• Relay intervention warning lamp

• Display range: -99 ÷ +999

• Display resolution: 0.1 RH or bar (-9.9 ÷ +99.9 RH or bar)

and 1 RH or bar (< -9.9 °C and > +99.9 RH or bar)

• Precision: ±0.5 % of the end of scale value ±1 digit

(at an ambient temperature of 23 °C)

• Sampling time: 0.5s

TECHNICAL SPECIFICATIONS

SAFETY WARNINGS

- 29 -

User Manual Regulators

English

• Parameter setting in digital mode:

- Set point

- Differential

- Neutral zone

- Output drive timing

- Digital input delay function and time

- Alarm delay / buzzer enable time

- Probe calibration offset

- Resolution displayed

- Measurement display filter (update speed)

- Type of probe input

- Password

- Operating modes (regulation):

— ON/OFF Direct and/or Reverse action with or without neutral zone

— PWM Direct and Reverse action with or without neutral zone

— ALARM

— Special mode

• 2 independent set points

• Digital input: 1 (not versions HR-..P7A, PR-..P7A) for outside consensus

for configurable function: outside alarm, regulator ON/OFF, set-point switching,

Direct/Reverce switching, etc.

Acoustic and visual alarm signalling for: outside alarm (from digital input),

probe alarm (malfunction), minimum or maximum alarm

• Infrared receiver with RC-5 protocol for remote control (accessory available

separately for remote programming)

• Available in the following fixing versions: 33x75 mm rear panel, 72x72 mm

rear panel and modular 4 DIN

• Power supply: see table on the following page

• Rated power: 3 VA for models with 33x75 mm rear panel fixing

4.5 VA for models with 72x72 mm and modular 4 DIN fixing

• Max absorption: 100 mA at 12 V - 50 mA at 24 V (1 channel)

• Operating temperature: 0 ÷ +50 °C

• Operating humidity: <80%

• Storage temperature: -10 ÷ +70 °C (<80% RH)

• Protection level: front panel IP54 (IP40 for the 4 DIN module version)

terminals IP20

Produktspecifikationer

Varumärke:	Vemer
Kategori:	Inte kategoriserad
Modell:	PR-1DA

Behöver du hjälp?

Om du behöver hjälp med Vemer PR-1DA ställ en fråga nedan och andra användare kommer att svara dig

Ditt namn*

Din e-post*

Skriv din fråga här

Inte kategoriserad Vemer Manualer

Vemer PR-1DA Bruksanvisning

4 Oktober 2024

Vemer TCR Bruksanvisning

3 Oktober 2024

Vemer Set PC RF8 Bruksanvisning

1 Oktober 2024

Vemer HT NiPt-2P3A Bruksanvisning

22 September 2024

Vemer ADR-D Vision Bruksanvisning

22 September 2024

Vemer Athena.Temp Bruksanvisning

22 September 2024

Vemer FR NTC-4P3D Bruksanvisning

21 September 2024

Vemer LSM-01 Bruksanvisning

18 September 2024

Vemer Phono Bruksanvisning

16 September 2024

Vemer Elettrosonda Z Bruksanvisning

14 September 2024

Inte kategoriserad Manualer

Nyaste Inte kategoriserad Manualer

Philips 43PUL7672 Bruksanvisning

27 Oktober 2024

Manhattan 461504 Bruksanvisning

27 Oktober 2024

Sungrow SG125HV Bruksanvisning

27 Oktober 2024

Schneider CCT724319 Bruksanvisning

27 Oktober 2024

Technoline WS 250 Bruksanvisning

27 Oktober 2024

Livarno IAN 354423 Bruksanvisning

27 Oktober 2024

Kupper 12152 Bruksanvisning

27 Oktober 2024

JennAir CARBON24L Bruksanvisning

27 Oktober 2024

Medion Life E74001 (MD 81035) Bruksanvisning

27 Oktober 2024

POLARIS Sportsman Touring 850 SP (2015) Bruksanvisning

27 Oktober 2024