VETTA RT Classic Bruksanvisning
VETTA
Cykeldator
RT Classic
Läs nedan 📖 manual på svenska för VETTA RT Classic (2 sidor) i kategorin Cykeldator. Denna guide var användbar för 7 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare
Sida 1/2
RT Classic & RT233
9
RT Classic RT233
Speed (Current)
Speed (Avg / Max)
Cumulative Odometer
Trip Distance
Freeze Frame Memory
LCD Screens
12 /24 Hour Clock
Interchangeable Front Cover
EZ Tire Setup
22
Service Timer
HEAD UNIT (RT233)
HEAD UNIT (RT Classic)
Vetta cycle computers are sophisticated electronic instruments. Vetta recommends that
this product be installed only by a qualified bicycle retailer. Failure to read these instructions
and/or improper installation of this device may void the warranty. If in doubt about any
aspect of the installation or operation of this product, consult your local bicycle retailer for
clarification.
RT Classic:
RT233:
Attach the Wired Speed Sensor with the Zip-Ties supplied and tighten the Bladed Spoke
Magnet to the bicycle.
Mounting the sensor as high up on the fork leg as possible. (see
Fig.A).
Adjust the sensor and magnet spacing with the Spacer. Remove the Spacer
after
tightening the Zip-Tie down to hold the sensor in its final position.
MOUNTING BRACKET & HEAD UNIT
Wired Mounting Bracket
Head Unit Head Unit
UNLOCK
Loocking Tab
Wired Mounting Bracket
UNLOCK
Loocking Tab
Step 1:
Advance the computer to the SPD screen mode using Buttong #2.
Step 2:
Pick up the front of the bicycle and spin the front wheel or ride the bicycle a short distance.
The LCD should display a speed reading within 2-3 seconds.
If there is no speed reading, check the alignment and spacing between the magnet and sensor.
Make sure that the Head Unit is completely locked into position. If these checks do not solve the
problem, talk to an Authorized Vetta’s Retailer or connect to www.vetta.com/support.asp.
CLASSIC
CLASSIC
CLASSIC
8
The head unit is water resistant and sealed to withstand wet weather conditions. However,
do not deliberately place it in water.
Avoid leaving the head unit exposed to extremely hot weather conditions.
Vetta encourages you to ride safely. Wear a helmet every time you ride, use front and rear
lights at night, and always keep your eyes on the road ahead of you.
1
Set / Select Button (Left)
2Mode / Advance Button (Right)
AUpper Display (Speed)
B Service Timer Icon
C Speed / Distance Units
D Lower Display
E Function Icons
A
Contact Points
B
Battery Compartment
C
Battery Coner
Important:
Use the tapes provided with the package (NOT ZIP-TIES) to hold wires to the
frame, fork, bars or stem to avoid damaging or cutting the wires accidently. Make sure excess
wire is taped down or wrapped around brake cable housing to secure it.
The Head Unit uses a CR2032 3-Volt Lithium
button cell battery.
Battery Run Time (1 hour training / day): Approx. 12 months
Important: Most cycle computer problems are caused by weak or
dead batteries. See the Trouble Shooting section near the end of
the manual for details.
1. Remove the battery cap from the bottom of the
Head Unit using a coin.
2. Install a new battery as shown with the positive
(+) side facing out. Do not touch or bend any
of the battery contacts during installation.
3. Screw the battery cap firmly into place making
sure the O-ring seal does not get pinched or distorted.
Caution: To avoid damage to the battery cap, do not over tighten.
Press momentarily
Press & hold for 2 seconds
1 Set / Select Button (Left)
2Mode / Advance Button (Right)
Button & when the lowest screen is in the CLK Mode: NOM Setup
12
Button & when the lowest screen is in the DST Mode: Reset Ride Data
12
Note: Secure wire with tape supplied and by winding it around cables. Be sure to leave
enough slack in the wire to accommodate the movement of fork and handlebars.
Attach Mounting Bracket to the handlebar on the “Sensor Side”. Adjust its position to your liking
and fasten the screw.
Slide the Head Unit into the Wired Mounting Bracket as shown until it clicks into position.
Remove by pressing in the locking tab as shown.
Once installation is complete, the computer should be tested to make sure it is working properly.
Important: Once the sensor is aligned, tighten the magnet’s locking screw and Mounting Bracket
Strap.
Service Timer could be programmed with a selected number of ride
time hours as the interval for servicing the bicycle or any component
on it, such as a front or rear shock.
Accumulated Ride Time is displayed on the upper line and Service
Time is displayed on the lower line. To set the service Time, press
Button #2 to advance hour digits. (The hour digits appear on the
lower level with the right hand digit flashing.) Press Button #1 to
select and advance to next digit. (Maximum hour setting=1999 hours)
The default setting for the Service Timer is “0000” hours, which
means the Service Timer is turned off.
Service Timer could be programmed with a selected number of ride time (hours or days)
or distance as the interval for servicing the bicycle or any component on it, such as a front
or rear shock.
Press to scroll flashing hr (hour), day or dst (distance) as the Service Time unit. Press
to select the desired Service Timer unit.
When the desired Service Timer unit has been chosen, press to scroll the flashing digit
to the desired number. Press to select this number and advance to next digit. Repeat
this procedure until all digits are selected.
Press to advance the next setup Mode. (Maximum settings: hour / day / distance=1999
/ 199 / 9999)
1
2
1
2
1
When the Ride Time (the elapsed time for Service
Timer) or the elapsed
distance begins
to flash, press & hold to reset to zero;
OR press to reserve the digits, and advance to the next Setup Mode.
1
2
Important: In the Initial Setup, the elapsed time [ distance] for Service Timer doesn’t exist.
Press Button #2 to switch between “M/hr” and “KM/hr” and Button #1 to select desired units
and advance. (To change units in SPD / ODO
screen mode, press and hold Buttons #1 and
#2 simultaneously for 2 seconds until “M/hr” begins
to flash).
In Setup, Button is used to select or set a value and to advance to the next digit or Mode.
Button is used to switch between settings and to increase values.
1
1
2
2
RT233 (RT Classic) is programmed to enter the Initial Setup Mode after new battery replacement.
In the Initial Setup, riders can program the Basic Settings for the computer, the content of
settings are same as NOM Setup for Basic Setting.
Initial Setup
NOM Setup
After completed the Initial Setup, riders can change any values or correct any errors by re-entering
the NOM Setup. To enter the NOM Setup Mode, press & hold & simultaneously when the
lowest screen is in the aclk Mode.
Important:
Computer CANNOT exit during the Setup Mode until all the Basic Settings are finished.
Press to toggle between flashing 12 and 24 hour formats. Press to select your desired
format (without PM icon implies AM in 12 hour format) and advance to Time setting.
2
2
2
2
1
1
1
1
Press to advance hour digits to correct hour (hold button for rapid advacne). Press to select
and advance to minute setting. Press to advacne minute digits to correct minute. Press to
select and advance to the next Setup Mode.
Press to toggle between flashing M/hr and KM/hr.
Press to select and advance to teh next Setup
Mode.
1.
Wired Speed Sensor with Mounting Bracket
2. Extra Clear Front Cover
3. Bladed Spoke Magnet
4. Spacer
5. Head Unit Battery (CR2032, 3-Volt)
6. Wire Securing Tape
7. Zip-Ties
8. Screw Strap
1. Button 3. Main Display 5. Battery Compartment
2. Button 4. Contact Pins 6. Battery Cap
1
2
(RT Classic)
(RT Classic)
(RT233)
The default settings “0000” means the Service Timer is turned off.
(RT Classic)
(RT233)
(RT Classic)
(RT Classic)(RT233)
(RT233)(RT233)
(RT233)(RT233)
Universal Bike Mount
2
2
1
1
circ
tire,
If pre-set to (see Table of Tire Size Vs Circ), press to scroll the flashing digit to the desired number.
Press to select this number and advance to next digit. Repeat this procedure until all four digits are
selected.
1
2
If pre-set to press to scroll the flashing
700c, 650c, 27in, 26in, 24in, 20in or 16in.
Press
select and advance to next setting to complete the Tire Size. Again, press to scroll and press
to finalize
the Size Tire and advance to the next Setup
Mode.
to
700C x 20mm
650C x 23mm
650C x 20mm
27” x 1-1/4”
27” x 1-1/8”
TIRE SIZE
700C x 35mm
700C Tubular
700C x 32mm
26” x 1-1/4”
26” x 1.0”
24” x 1.9/1.95”
20” x 1-1/4”
16” x 2.0”
16” x 1.95”
16” x 1-1/2”
26” x 2-1/4”
26” x 2.1”
26” x 2.0”
26” x 2.3”
26” x 1.9/1.95”
26” x 1-3/4”
26” x 1-1/2”
2074
700C x 23mm 2105
700C x 25mm 2124
700C x 28mm 2136
700C x 30mm 2145
2155
2168
700C x 38mm 2180
2130
1990
1945
2135
2055
1253
1257
1916
1206
1618
2161
2155
2074
2095
2115
1913
1953
1985
2035
CIRC TIRE SIZE CIRC TIRE SIZE CIRC
TIRE SIZE CIRC
SPD
SPD
Speed is shown at all times on upper display. It is accurate to 0.1 M/hr
or KM/hr and the maximum reading is 139.9M/hr or 199.9 KM/hr.
ACUMEN INC. WARRANTS ALL VETTA (The Company) PRODUCTS AGAINST
MANUFACTURER DEFECTS FOR A PERIOD OF 3 YEARS. Subject to the following
limitations, terms and conditions, components will be free of manufacturing defects in
materials and workmanship. The 3 year limited warranty is conditioned upon the
components being used and operated in normal riding conditions. This warranty does not
cover normal wear and tear (i.e. battery replacement, broken wire), rider abuse, acts of
God, improper installation or product alteration.
This warranty is void if the components were not purchased (new) from or through
an authorized VETTA retailer or dealer. Examples of unauthorized dealers are
online auction sites or online retailers.
ACUMEN INC. at its sole discretion will repair or replace items at its own cost. Users are
responsible for all freight and shipping charges, when returning items for warranty
service.
ACUMEN INC. will pay the freight when returning serviced items, via USPS or UPS to
consumers or dealers, once the item(s) has been repaired or replaced.
REQUIREMENTS FOR WARRANTY SERVICING
1. Prior to shipping an item back, you must first obtain a Return Authorization Number (s)
(RA#). Each item being returned must have an individual RA#.
Time is displayed in use-selected 12 / 24 hour formats.
Computer enters Sleep Mode after 5 minutes without input from any buttons
or wheel, and displays the clock only. Computer exits Sleep Mode and returns
to the screen last displayed when any button is pressed or the wheel turns.
Default wheel circumference setting is 2074mm. Choose correct wheel
circumference figure from Wheel Reference Chart.
Press Button #2 to advance digits as needed and Button #1 to select
and advance. (Range: 0050-2999mm)
Press to scroll the flashing digit to the desired
number. Press to select this number and
advance to next digit. Repeat this procedure until all five digits are selected. Press to
advance the next Setup Mode. (Maximum setting: 99999)
1
1
1
2
2
12
Press to scroll the lower screen Modes.
To enter the NOM Setup Mode, press & hold & simultaneously for 2 seconds when
the lowest screen is in the CLK Mode;
To reset Ride Data to zero, press & hold and simultaneously for 2 seconds when
the lowest screen is in the DST Mode.
2
The odometer displays distance to 99999 Miles or kilometers. It is
accurate to 1.0 Mile or KM.
Blinking “ ” alerts rider the Service Time is reached.
Screen is dark and display characters look “strange”.
Screen reading is weak or fading.
Screen readings are erratic and read too high or too low.
Screen “frozen”, no response to buttons.
No display whatsoever.
Battery is completely dead or not installed. Replace or install the battery.
Symptom of a weak battery. Replace the battery.
Computer screens do not like to be left in direct sunlight for extended periods of time.
Move the computer into the shade until the screen recovers. No effect on data.
Acumen Inc.
101A Executive Drive Suite 100, Sterling, VA 20166 USA
In USA, securely package and return the product prepaid to:
(RT Classic)
(RT Classic)
(RT233)
1
2
2 1
1 1 1
WHEEL/ TIRE SIZE
Press to toggle between flashing circ (circumference) and tire (tire type). Press to
select the desired and advance the settings.
21
(RT233)
TROUBLE SHOOTING
Current speed reading is erratic or does not appear.
Current speed reading is erratic or does not appear.
Incorrect data appears on screen during operation.
Data dispaly is extremely slow.
Check the alignment of the wheel magnet and sensor, and the distance between the two
components. Realign the magnet and sensor with the spacer.
Inspect the wiring for any breaks or kinks. Replace mounting bracket and sensor as
needed.
Accuracy of the Setup data may be a problem (wheel size setting, etc.)
Computer LCD does not like extremely low temperatures. Operating range is: 0°C to 50°C
or 32°F to 122°F. Return the computer to a warmer climate.
Note: When the Trip Distance
exceeds 999.9 miles [kilometers],
symbol “E” appears indicating
that further measurement
is impossible.
DST displays trip distance
of current ride to a maximum
of 999.9 miles or kilometers.
It is accurate to 0.1 Mile or
KM.
Time is displayed in user-selected 12 or 24 hour formats.
The odometer displays distance to 99999 Miles or kilometers. It is
accurate to 1.0 Mile or KM.
Displays trip distance of current ride to a maximum of 999.9 miles or
kilometers (0.1 mile / km).
All Clear Reset: Remove battery and reinstall. When you remove the battery, all data and all
time and odometer setting will be cleared. When battery is reinstalled, computer will automatically
enter the Setup program.
Speed is shown at all times on upper display. It is accurate to 0.1 M/hr
or KM/hr and the maximum reading is 139.9M/hr or 199.9 KM/hr. All Clear Reset: Remove battery and reinstall. When you remove the battery, all data and all
time and odometer setting will be cleared. When battery is reinstalled, computer will automatically
enter the Setup program.
Blinking wrench icon alerts rider the Service Time is reached. To view or reset Accumulated
Ride Time and Service Time, press and hold Buttons #1 and #2 for 2 seconds in the SPD/CLK
screen mode.
To reset Accumulated Ride Time to “0”, hold Button #2 when upper digits are flashing during
Setup.
To conserve battery life, computer enters Sleep Mode after 5 minutes
without input from buttons or speed sensor and displays the time.
Computer exits Sleep Mode and returns to screen last displayed with
input from buttons or wheel.
2. To obtain an RA #, you must either contact the retailer where the product was originally
purchased from, or contact VETTA directly at customer service @ vetta.com.
3. For trouble shooting purposes, we request that the complete unit with packaging be
returned to ACUMEN INC. unless otherwise stated by VETTA representative.
ITEMS TO BE INCLUDED IN RETURNS
1. The defective product(s)
2. A letter clearly stating the problem(s) with the returned item(s).
3. Copy of the original sales receipt showing proof of purchase date.
4. The Company is not responsible for loss or additional damages while in transit to
ACUMEN INC.
5. Clearly mark the RA# on the outside of the return packaging. All items without an RA #
will be refused and returned to the return address on the package.
The Company shall not be held responsible for replacing items with new items for greater
than the amount of the original item purchase price. This limited warranty does provide the
original owner with certain legal rights and recourse. The original owner may possess other
rights or recourse, depending on the state or country. Please check the web to help answer
any question and service manual.
Outside USA, you should contact the local dealer or Acumen distributor in your country for
custom service.
Acumen Europe BV
Website: www.vetta.com
Email: customerservice@vetta.com
RT233
RT233
RT Classic
RT Classic
Produktspecifikationer
| Varumärke: | VETTA |
| Kategori: | Cykeldator |
| Modell: | RT Classic |
Behöver du hjälp?
Om du behöver hjälp med VETTA RT Classic ställ en fråga nedan och andra användare kommer att svara dig
Cykeldator VETTA Manualer
11 September 2024
10 September 2024
10 September 2024
28 Juli 2024
28 Juli 2024
28 Juli 2024
28 Juli 2024
Cykeldator Manualer
- Cykeldator Bosch
- Cykeldator Garmin
- Cykeldator Pioneer
- Cykeldator Topcom
- Cykeldator Ascot
- Cykeldator Crivit
- Cykeldator Timex
- Cykeldator Batavus
- Cykeldator Cateye
- Cykeldator Ventura
- Cykeldator Bryton
- Cykeldator BBB
- Cykeldator Trelock
- Cykeldator Polar
- Cykeldator Mio
- Cykeldator Sigma
- Cykeldator Bell
- Cykeldator Kayoba
- Cykeldator Vogue
- Cykeldator Hema
- Cykeldator Contec
- Cykeldator Lezyne
- Cykeldator Sunding
- Cykeldator Halfords
- Cykeldator Wahoo Fitness
- Cykeldator Echowell
- Cykeldator Magene
- Cykeldator Pro
- Cykeldator Stella
- Cykeldator IGPSport
- Cykeldator Cannondale
- Cykeldator Trek
- Cykeldator Prophete
- Cykeldator Powertap
- Cykeldator VDO
- Cykeldator CicloSport
- Cykeldator Bikemate
- Cykeldator Bontrager
- Cykeldator Sigma Sport
- Cykeldator BBB Cycling
- Cykeldator Osynce
- Cykeldator Cube
- Cykeldator Dresco
- Cykeldator Bafang
- Cykeldator Silent Force
- Cykeldator Cordo
- Cykeldator Knog
- Cykeldator Matrabike
- Cykeldator Speedmaster
- Cykeldator Wahoo
- Cykeldator Decathlon
- Cykeldator Axiom
- Cykeldator Rawlink
- Cykeldator Kellys
- Cykeldator Filmer
- Cykeldator Walfort
- Cykeldator Ciclo
- Cykeldator Stels
- Cykeldator Blackburn
Nyaste Cykeldator Manualer
18 Oktober 2024
12 Oktober 2024
4 Oktober 2024
2 Oktober 2024
2 Oktober 2024
30 September 2024
30 September 2024
29 September 2024
26 September 2024
25 September 2024