Yakima FrontLoader Bruksanvisning

Yakima Cykelhållare FrontLoader

Läs nedan 📖 manual på svenska för Yakima FrontLoader (18 sidor) i kategorin Cykelhållare. Denna guide var användbar för 6 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Sida 1/18
CROSSBAR SPREAD
1033644D-1/18
IMPORTANT WARNING
IT IS CRITICAL THAT ALL YAKIMA RACKS AND ACCESSORIES BE PROPERLY AND SECURELY ATTACHED TO YOUR VEHICLE. IMPROPER
ATTACHMENT COULD RESULT IN AN AUTOMOBILE ACCIDENT, AND COULD CAUSE SERIOUS BODILY INJURY OR DEATH TO YOU OR
TO OTHERS. YOU ARE RESPONSIBLE FOR SECURING THE RACKS AND ACCESSORIES TO YOUR CAR, CHECKING THE ATTACHMENTS
PRIOR TO USE, AND PERIODICALLY INSPECTING THE PRODUCTS FOR ADJUSTMENT, WEAR, AND DAMAGE. THEREFORE, YOU MUST READ AND
UNDERSTAND ALL OF THE INSTRUCTIONS AND CAUTIONS SUPPLIED WITH YOUR YAKIMA PRODUCT PRIOR TO INSTALLATION OR USE. IF YOU
DO NOT UNDERSTAND ALL OF THE INSTRUCTIONS AND CAUTIONS, OR IF YOU HAVE NO MECHANICAL EXPERIENCE AND ARE NOT THOROUGHLY
FAMILIAR WITH THE INSTALLATION PROCEDURES, YOU SHOULD HAVE THE PRODUCT INSTALLED BY A PROFESSIONAL INSTALLER.
FRONTLOADER (1X)
*CROSSBAR SPREAD
Your crossbar
spread is
the distance
between the
crossbars.
If you have factory crossbars, be sure you have
at least 1-1/2” (3.8 cm) of clearance between
the bottom of the crossbar and the vehicle roof.
16" - 18”
41cm - 46cm
18" - 48"
46cm - 122cm
Weight Limit
30 lbs. (13.6kg)/bike
40 lbs. (18.1kg)/bike
Crossbar Spread
DO NOT EXCEED RACK WEIGHT LIMITS!
DO NOT EXCEED RACK WEIGHT LIMITS!
2x max.
90°
1033644D-2/18
Place FrontLoader onto crossbars.
Open the front clamp. Turn the
front knob counter clockwise
to open the front the clamp.
Open the rear clamp.
It may be necessary to turn the t-bolt to allow
it to pass through the slot in the clamp.
Use caution to avoid damaging
roof’s finish. A towel placed
on the roof prior to installation
can help avoid scratches.
Lower the front
clamp into place
over front crossbar.
Slide the jaw of the
rear clamp under
rear crossbar.
Tighten clamps.
Tighten the front clamp.
Turn the knob clockwise to
completely tighten the front
clamp around crossbar.
Tighten the rear clamp.
Close rear clamp
around rear crossbar.
Upper notch for round
and square bars.
For factory bars
choose the best
position for most
secure grip.
Pass the t-bolt through the opening in bail.
Rotate t-bolt to rest in slot in bail.
Adjust clamp if necessary. If you don’t get a secure grip with
your factory bars adjust your clamp.
Turn the knob clockwise to completely tighten the rear clamp.
1033644D-3/18
The rear clamp is configured for typical installations. In some situations adjustment may be necessary
if the wheel makes contact with the rear knob, or if the wheeltray cannot reach the wheel.
Remove wheeltray
and rear clamp.
Flip orientation of
rear clamp 180˚.
Install endcap.
NOTE: You can flip the wheeltray or rear clamp independently
as needed. For instance if you needed the buckle on the
opposite side you could flip the wheeltray as shown.
Slide wheeltray and rear
clamp back onto forks.
Press the release
tabs on the end
cap and remove it.
Wheel behind
rear crossbar.
OPTION A
Wheel ahead of
rear crossbar.
OPTION B
If changing the
orientation of the rear
clamp still results in the
rear wheel contacting
the knob, please contact
our customer service
team (888-925-4621) for a
free, corrective adapter.

Produktspecifikationer

Varumärke: Yakima
Kategori: Cykelhållare
Modell: FrontLoader

Behöver du hjälp?

Om du behöver hjälp med Yakima FrontLoader ställ en fråga nedan och andra användare kommer att svara dig