AudioSource AMP102VS Bruksanvisning

AudioSource mottagare AMP102VS

Läs nedan 📖 manual på svenska för AudioSource AMP102VS (5 sidor) i kategorin mottagare. Denna guide var användbar för 2 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF

Sida 1/5

OWNER’S MANUAL

AMP102VS

AudioSource®

13970 SW 72nd Ave

Portland, OR 97223

503.914.4688

www.audiosource.net AMP102VS Owner’s Manual 72015

Congratulations on your purchase of the AudioSource® AMP102VS.

Please take a few moments to read this entire manual, and be sure to

retain this document for future reference. Please read and observe all

safety instructions detailed on page 2.

NOTE: If any part of this product is damaged or missing, please call your

dealer or AudioSource® directly at 1.877.715.5439 or 503.914.4688.

Please read your warranty and retain your receipt and original carton

for possible future use.

For more information about AudioSource® electronics, speakers and

accessories please visit www.audiosource.net

AMP102VS

Stereo Power Amplifier

FEATURES:

MAIN / INTERRUPT priority input switching

MAIN auxiliary output

Speaker A/B switching

Front panel Balance and Volume controls

Signal sensing “Power On” and Trigger mode

SPECIFICATIONS

Stereo (8 ohm): 55W per channel, <0.2% THD+N

Stereo (4 ohm): 75W per channel, <0.2% THD+N

Bridged Mono (8 ohm): 160W, 1kHz, <0.2% THD+N

Frequency Response: 10Hz ~ 50kHz, +0dB/ -3dB

Signal to Noise Ratio: 100dB below 50W output into 8 ohms

Channel Separation: 70dB

Input Sensitivity: 700mV input for rated 50W output

into 8 ohms

AC Power Consumption: 500W maximum

Net Weight: 14lbs / 6.4kgs

Gross Weight: 17.4lbs / 7.9kgs

Rear mounted treble and bass controls

Bass/Treble Control: +/- 12dB @ 100Hz and 10kHz

3.8”

(96.5mm)

16.5” (419mm)

8.25”

(210mm)

13. Unplug the apparatus during lightning storms or when unused for long periods

of time.

14. Refer all servicing to qualified personnel. Servicing is required when the

apparatus has been damaged in any way, such as power supply cord or

plug is damaged, liquid has been spilled or objects have fallen into the

apparatus has been exposed to rain or moisture, does not operate normally,

or has been dropped.

15. WARNING: To reduce the risk of fire or electric shock, do not expose this

apparatus to rain or moisture. The apparatus shall not be exposed to

dripping or splashing and that objects filled with liquids, such as vases,

shall not be placed on apparatus.

16. WARNING: The mains plug/appliance coupler is used as disconnect device,

the disconnect device shall remain readily operable.

17. This equipment is a Class II or double insulated electrical appliance. It

is designed in such a way that it does not require a safety connection

to electrical earth.

18.

- This lightning flash with arrowhead symbol within an equilateral triangle is

intended to alert the user to the presence of non-insulated “dangerous voltage”

within the product’s enclosure that may be of sufficient magnitude to constitute

a risk of electric shock.

- Warning: to reduce the risk of electric shock, do not remove cover (or back) as

there are no user-serviceable parts inside. Refer servicing to qualified personnel.

- The exclamation point within an equilateral triangle is intended to alert the user

to the presence of important operating and maintenance instructions in the

literature accompanying the appliance.

AMP102VS

OWNER’S MANUAL

13970 SW 72nd Ave, Portland, OR 97223 • 503.914.4688 • www.audiosource.net

CAUTION

RISK OF ELECTRICAL SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE THE COVER. NO

USER SERVICABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED PERSONNEL!

IMPORTANT SAFETY INSTRUCTIONS

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. The ventilation should not be impeded

by covering the ventilation openings with items such as newspaper, table-

cloths, curtains etc. Install in accordance with the manufacturer’s instructions.

8. Do not install near heat sources such as radiators, heat registers, stoves,

or other apparatus (including amplifiers) that produce heat. No open flame

sources, such as lighted candles, should be placed on the apparatus.

9. Do not defeat the safety purpose of the polarized or grounding type plug.

A polarized plug has two blades with one wider than the other. A grounding

type plug has two blades and a third grounding prong. The wide blade or

third prong is provided for your safety. If the provided plug does not fit into

your outlet, consult an electrician for replacement of the obsolete outlet.

MAGNETIC FIELD: !!CAUTION!! Do not locate sensitive high-gain equipment such as preampliﬁers or tape decks directly above or below the unit. Because

this ampliﬁer has a high power density, it has a strong magnetic ﬁeld, which can induce hum into unshielded devices that are located nearby. The ﬁeld is

strongest just above and below the unit. If an equipment rack is used, we recommend locating the ampliﬁer(s) in the bottom of the rack and the preampliﬁer

or other sensitive equipment at the top.

EXPLANATION OF

SAFETY SYMBOLS

The exclamation point within an equilateral triangle is intended to alert the user of the presence of important

operating and maintenance (servicing) instructions in the literature accompanying the appliance.

The lightning ﬂash with the arrowhead symbol within an equilateral triangle is intended to alert the user to the

presence of uninsulated “dangerous voltage” within the products’ enclosure that may be of sufﬁcient magnitude

to constitute a risk of electric shock to persons.

10. Protect the power cord from being walked on or pinched particularly at the

plugs, convenience receptacles, and at the point of exit from the apparatus.

11. Only use attacheements/accessories specified by the manufacturer.

12. Use only with the cart, stand, tripod, bracket, or

table specified by the manufacturer, or sold with

the apparatus. When a cart or rack is used, use

caution when moving the cart/apparatus

combination to avoid injury from tip-over.

• WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. THE APPARATUS SHALL NOT

BE EXPOSED TO DRIPPING OR SPLASHING AND THAT OBJECTS FILLED WITH LIQUIDS, SUCH AS VASES, SHALL NOT BE PLACED

ON APPARATUS.

• WARNING: TO PREVENT FIRE OF SHOCK HAZARD, DO NOT USE THIS PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUTLET

UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE.

• WARNING: THE MAINS PLUG IS USED AS DISCONNECT DEVICE. THE DISCONNECT DEVICE SHALL REMAIN READILY AVAILABLE.

• WARNING: ONLY USE ATTACHMENTS OR ACCESSORIES SPECIFIED OR PROVIDED BY THE MANUFACTURER.

AMP102VS

OWNER’S MANUAL

13970 SW 72nd Ave, Portland, OR 97223 • 503.914.4688 • www.audiosource.net 3

1. Power Switch

Switches the AMP102VS on or off.

2. Speaker Selector

Selects speaker zone A or B. For A + B zones push both buttons in.

3. Balance

Fades speaker output between the Right and Left Channels

4. Volume

Adjusts ampliﬁer volume.

FRONT PANEL CONTROLS

7. Interupting Line Input

This is the secondary input, use MAIN IN for your main input.

INTERRUPTING INPUT can be used if a second source is desired and

takes over when signal is present and has at least a 5mV level.

When there is no signal, or a signal with less than 5mV level, the amp

switches back to MAIN IN after a brief delay.

Main Input/Output

11.

12.

Mode Select Switch

Switches the ampliﬁer from Stereo mode to Bridged mode.

13.

Power Mode Select Switch

Speaker Zone A Output

Speaker output terminals for zone A. Minimum impedance: 8 ohm bridged

or 4 ohm stereo.

Speaker Zone B Output

Speaker output terminals for zone B. Minimum impedance: 8 ohm bridged

or 4 ohm stereo.

REAR PANEL CONTROLS

Figure 1. Front Panel

Figure 2. Rear Panel

MAIN IN should be used as the “primary” or main input for the ampliﬁer.

Connect your receiver or main source to this input. Use MAIN OUT to pass

MAIN IN signal to another amplifier.

If you will be connecting one or two pair of speakers to the ampliﬁer, place

the switch in the “Stereo” position. NOTE: For playing 2 pairs of speakers

(A plus B), make sure each speaker has an impedance of 8 ohms or greater.

When set to “Bridged” mode, the ampliﬁer is a single channel mono amplifier.

NOTE: The AMP102VS supplies 160W in bridged mode, Please verify that your

speakers are capable of handling such power to avoid possible damage!

For stereo output connect the speaker’s positive (red) terminal to the ampliﬁer’s

positive (red) terminal, and the speaker’s negative (black) terminal to the

ampliﬁer’s negative (black) terminal for each Right and Left speaker.

Place the “MODE” switch in the “BRIDGED” position and use both red

terminals to connect to the speaker. Connect the speaker’s positive (red)

terminal to the ampliﬁer’s red (+) terminal noted next to the bridging mark, and

the speaker’s negative (black) terminal to the ampliﬁer’s unmarked positive

NOTE: Only one zone (A or B) can be bridged. Do not attempt to bridge both

A and B speaker terminals! This may result in a lower impedance than the

ampliﬁer is designed for and may damage your ampliﬁer. The minimum

impedance for the total load connected in bridged mode is 8 ohms.

STEREO MODE

BRIDGED MODE

BRIDGED MODE- MONO APPLICATION

For bridged mode, playing Right and Left together as mono output, use a

Y cable adapter to connect Right and Left RCA signal to the Right (Red) input

at MAIN IN. Set the MODE switch to BRIDGED and follow the instructions

for bridged speaker connection in the SPEAKER TERMINALS section of

this manual.

SPEAKER TERMINALS - STEREO MODE

SPEAKER TERMINALS - BRIDGED MODE

6. Bass and Treble Controls

These controls can adjust bass and treble frequencies +/- 12dB at 100Hz

and 10kHz.

10. 12V Trigger

Allows the AMP102VS to be powered on by other electronics or to power

on other electronics via a 3.5mm mini phone plug cable.

(red) terminal.

NOTE: Use Class 2 wiring for speaker connections.

To wire the output connector: 1. Strip the insulation off each speaker wire

to expose 3/8" (10 mm) of bare conductor. 2. Unscrew the output terminal

binding post several twists, insert each wire into the correct terminal.

3. Tighten binding post by twisting clock-wise until it is firmly clamping the

speaker wire.

Warning: While the amplifier does self-protect under most improper output

conditions, misconfiguration of loudspeaker mode and incorrect connection

of loudspeakers could damage connected loudspeakers and/or amplifier.

Please refer installation to a qualified installation professional, and always

check state and local electrical codes when installing.

10 11

13 14

Minimum Impedance:

8 ohm Bridged

4 ohm Stereo

AVIS: RISQUE DE CHOC ELECTRIQE

NE PAS OUVRIR CE CART ER

RESERVE AU PERSONNEL AUT ORISE

RISK OF FIRE O R ELECT RIC SHOCK

DO NOT OPEN

CAUTION AVIS

Trigger Normal

Auto On

Mode

Stereo Bridged

115V~ 60Hz 500W

FUSE:T4AL 250V

FUSE:T2AL 250V

230V~ 50Hz 500W

MODEL AMP102VS

Custom Manufactured in China

CAUTION: See User Manual Before

Replacing Fuse

Speaker A

R L

+ +

Bridge

Speaker B

IN OUT

12V Trigger

Interrupt

Serial Number:

IN OUT

Main In

Sets the power on option of the AMP102VS. Set it to Normal for manual

power on/off. Set to Auto-On for signal sensing. Set to Trigger if the 12V

Trigger input is used.

Produktspecifikationer

Varumärke:	AudioSource
Kategori:	mottagare
Modell:	AMP102VS

Behöver du hjälp?

Om du behöver hjälp med AudioSource AMP102VS ställ en fråga nedan och andra användare kommer att svara dig

Ditt namn*

Din e-post*

Skriv din fråga här

mottagare AudioSource Manualer

AudioSource AMP 50 Bruksanvisning

10 December 2024

AudioSource AMP102 Bruksanvisning

10 December 2024

AudioSource AMP310 Bruksanvisning

10 December 2024

AudioSource AMP310VS Bruksanvisning

10 December 2024

AudioSource AMP102VS Bruksanvisning

10 December 2024

AudioSource AMP210 Bruksanvisning

10 December 2024

AudioSource AMP800VS Bruksanvisning

10 December 2024

AudioSource AMP1200VS Bruksanvisning

10 December 2024

AudioSource AMP100VS Bruksanvisning

10 December 2024

AudioSource AD508 Bruksanvisning

10 December 2024

mottagare Manualer

Nyaste mottagare Manualer

A-NeuVideo ANI-0108POE-AU Bruksanvisning

11 December 2024

Jensen XDA95RB Bruksanvisning

11 December 2024

AVMATRIX SD1121-12G Bruksanvisning

11 December 2024

AVMATRIX SD1191 Bruksanvisning

11 December 2024

ButtKicker BKA1000-P Bruksanvisning

11 December 2024

Phonic NT2504 Bruksanvisning

11 December 2024

Phonic DMA8825 Bruksanvisning

11 December 2024

Phonic MAX 1000 Bruksanvisning

11 December 2024

Phonic XP 5000 Bruksanvisning

11 December 2024

Phonic Xtrix 4100 Bruksanvisning

11 December 2024