AudioSource AMP800VS Bruksanvisning

AudioSource mottagare AMP800VS

Läs nedan 📖 manual på svenska för AudioSource AMP800VS (4 sidor) i kategorin mottagare. Denna guide var användbar för 3 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF

Sida 1/4

OWNER’S MANUAL

AMP800VS

AudioSource®

13970 SW 72nd Ave

Portland, OR 97223

503.914.4688

www.audiosource.net AMP800VS Owner’s Manual 72015

Congratulations on your purchase of the AudioSource® AMP800VS.

Please take a few moments to read this entire manual, and be sure to

retain this document for future reference. Please read and observe all

safety instructions detailed on page 2.

NOTE: If any part of this product is damaged or missing, please call your

dealer or AudioSource® directly at 1.877.715.5439 or 503.914.4688.

Please read your warranty and retain your receipt and original carton

for possible future use.

For more information about AudioSource® electronics, speakers and

accessories please visit www.audiosource.net

FEATURES:

SPECIFICATIONS

Stereo (8 ohm): 8 x 40W per channel, <0.2% THD+N

Stereo (4 ohm): 8 x 40W per channel, <0.2% THD+N

Bridged Mono (8 ohm): 80W, 1kHz, <0.2% THD+N

Frequency Response: 10Hz ~ 50kHz, +0dB/ -3dB

Signal to Noise Ratio:

100dB below 150W output into 8 ohms

Channel Separation: 70dB @ 1kHz, referred to 150W output

into 8 ohms

Input Sensitivity: Variable, 350mV to 2.8V for rated power

into 8 ohms

AC Power Consumption: 450W maximum

Net Weight: 27lbs / 13.6kgs

Gross Weight: 33lbs / 16.3kgs

Multi-Zone Power Amplifier

AMP800VS

8 Independent Channel inputs, 2 Buss Inputs

2 Buss Outputs

Independent Channel Gain Controls

Manual, Auto, or Triggered On/Off Modes

Bridgeable Channel Outputs

Rack Mountable (Rack Mount Included)

LED Status Indicator Lights

Phoenix-Style Speaker Connectors

Stable Class A/B Design

Extensive Protection Circuitry

MULTI-ZON E POWER AMPLIFIER

AMP800VS

4.0”

(102mm)

16.5” (419mm)

14.25”

(361mm)

13. Unplug the apparatus during lightning storms or when unused for long periods

of time.

14. Refer all servicing to qualified personnel. Servicing is required when the

apparatus has been damaged in any way, such as power supply cord or

plug is damaged, liquid has been spilled or objects have fallen into the

apparatus has been exposed to rain or moisture, does not operate normally,

or has been dropped.

15. WARNING: To reduce the risk of fire or electric shock, do not expose this

apparatus to rain or moisture. The apparatus shall not be exposed to

dripping or splashing and that objects filled with liquids, such as vases,

shall not be placed on apparatus.

16. WARNING: The mains plug/appliance coupler is used as disconnect device,

the disconnect device shall remain readily operable.

17. This equipment is a Class II or double insulated electrical appliance. It

is designed in such a way that it does not require a safety connection

to electrical earth.

18.

- This lightning flash with arrowhead symbol within an equilateral triangle is

intended to alert the user to the presence of non-insulated “dangerous voltage”

within the product’s enclosure that may be of sufficient magnitude to constitute

a risk of electric shock.

- Warning: to reduce the risk of electric shock, do not remove cover (or back) as

there are no user-serviceable parts inside. Refer servicing to qualified personnel.

- The exclamation point within an equilateral triangle is intended to alert the user

to the presence of important operating and maintenance instructions in the

literature accompanying the appliance.

AMP800VS

OWNER’S MANUAL

13970 SW 72nd Ave, Portland, OR 97223 • 503.914.4688 • www.audiosource.net

CAUTION

RISK OF ELECTRICAL SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE THE COVER. NO

USER SERVICABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED PERSONNEL!

IMPORTANT SAFETY INSTRUCTIONS

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. The ventilation should not be impeded

by covering the ventilation openings with items such as newspaper, table-

cloths, curtains etc. Install in accordance with the manufacturer’s instructions.

8. Do not install near heat sources such as radiators, heat registers, stoves,

or other apparatus (including amplifiers) that produce heat. No open flame

sources, such as lighted candles, should be placed on the apparatus.

9. Do not defeat the safety purpose of the polarized or grounding type plug.

A polarized plug has two blades with one wider than the other. A grounding

type plug has two blades and a third grounding prong. The wide blade or

third prong is provided for your safety. If the provided plug does not fit into

your outlet, consult an electrician for replacement of the obsolete outlet.

MAGNETIC FIELD: !!CAUTION!! Do not locate sensitive high-gain equipment such as preampliﬁers or tape decks directly above or below the unit. Because

this ampliﬁer has a high power density, it has a strong magnetic ﬁeld, which can induce hum into unshielded devices that are located nearby. The ﬁeld is

strongest just above and below the unit. If an equipment rack is used, we recommend locating the ampliﬁer(s) in the bottom of the rack and the preampliﬁer

or other sensitive equipment at the top.

EXPLANATION OF

SAFETY SYMBOLS

The exclamation point within an equilateral triangle is intended to alert the user of the presence of important

operating and maintenance (servicing) instructions in the literature accompanying the appliance.

The lightning ﬂash with the arrowhead symbol within an equilateral triangle is intended to alert the user to the

presence of uninsulated “dangerous voltage” within the products’ enclosure that may be of sufﬁcient magnitude

to constitute a risk of electric shock to persons.

10. Protect the power cord from being walked on or pinched particularly at the

plugs, convenience receptacles, and at the point of exit from the apparatus.

11. Only use attacheements/accessories specified by the manufacturer.

12. Use only with the cart, stand, tripod, bracket, or

table specified by the manufacturer, or sold with

the apparatus. When a cart or rack is used, use

caution when moving the cart/apparatus

combination to avoid injury from tip-over.

• WARNING: TO PREVE FIRE OR SHOCK HAZARD, DO NNT OT T PPARA EXPOSE THIS APPLIANCE O RAIN OR MOISTURE. THE A TUS SHALL NOT

BE EXPOSED T HAT VO DRIPPING OR SPLASHING AND T OBJECTS FILLED WITH LIQUIDS, SUCH AS ASES, SHA NLL OT D BE PLACE

ON APPARATUS.

• WARNING: TO PREVENT FIRE OF SHOCK HAZARD, DO NOT USE THIS PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUTLET

UNLESS THE BLADES CAN BE FULLY ER T INS TED O PREVENT BLADE EXPOSURE.

• WARNING: THE MAINS PLUG IS USED AS DISCONNECT CT DEVICE. THE DISCONNE DEVICE SHALL REMAIN READILY AVAILABLE.

• WARNING: ONLY USE ATTACHMENTS OR ACCESSORIES SPECIFIED OR PROVIDED BY UF THE MAN ACTURER.

AMP800VS

OWNER’S MANUAL

13970 SW 72nd Ave, Portland, OR 97223 • 503.914.4688 • www.audiosource.net 3

FRONT PANEL CONTROLS

REAR PANEL CONTROLS

Figure 1. Front Panel

10.

11.

Figure 2. Rear Panel

MULTI-ZONE POWER AMPLIFIER

AMP800VS

Master Power Switch / Indicator LED

Front panel pushbutton power switch turns the ampliﬁer on and off. When the

switch is on and the indicator LED is red, the ampliﬁer is in standby mode. The

remote turn on switch (located on the rear) is either in the “trigger” or “auto”

position. When the LED is blue, the ampliﬁer is fully active. The master power

switch will turn off the ampliﬁer no matter which power mode has been selected.

Zone Status Indicators

Each pair of channels or ones has bi-color LED z a to indicate its ope ationalr

status. These indicators pr video quick and easy trou leshootingb of the system. If the

circuitry deter a m do e ve low mines that channel ust be shut wn due to xcessi heat or

impedance (a sho t), only ther channels that ar af ectede f will be tu ned offr causing

the zone LED to tu rn red. The remaining zones will conti uen to ope ater and maintain

a b lue LED statu s. Once the condition has been corrected for zthe one in question,

the status LED will retu n to lur b e.

Note: When the pow er LED is red and the z one status LEDS are not lit (off) indicates

the unit is in stand y modb e.

3 6 7 8

4 5 9 10 12

BUS Line Inputs / Outputs

The AMP800VS has two common or BUS inputs that receives audio signals from

standard line-level audio sources and sends them to any or all channels. The BUS

line outputs are direct feed-through to allow the BUS inputs to be fed to other

ampliﬁers. Be sure to use high quality RCA cables that feature low impedance,

shielding and high quality connectors.

Remote Turn-On Switch

This s witch selects the tu n-onr sti ulim that will put the amplifier in ready mode.

“Trigger” setting relies on 3-30V AC/DC voltage going into the trigger input to

activate the ampliﬁer. “Auto” setting senses a signal on the RCA line-level inputs

and automatically puts the amp in ready mode. “On” setting puts the amp

constantly in ready mode so that it can be controlled by the master power switch

on the front panel. In “Auto” mode, the amplifier will take approsimately 15

minutes to return from ready to standby mode.

Trigger Input / Output

The trigger input is a handy feature when connecting the amplifier to an

automated audio system. The 3.5mm miniplug jack will accept a 3-30V AC/DC

output from another device, or from a separate power supply. When the trigger

input is energi ed,z the amp tu nsr from standby to ON mode. When using the

AMP800VS with a receiver without a trigger output, the voltage can come from a

12V wall wart (3.5mm tip-positive connector) plugged into the receiver’s switched

outlet and the trigger input. The AMP800VS can also provide an output trigger

voltage (12DC @500mA max.) to turn on and off other devices in the audio system.

When the amplifier turns off (standby mode), the voltage will drop to zero.

Channel Gain Control

Each channel has its own independent level adjustment. This allows the output

level of each speaker to be perfectly matched to its area. It can also be used to

limit the maximum audio level in a certain area.

Bridging Switch

By simply flipping a single switch, two channels can be combined to increase the

total power output. This is helpful when extra power is needed in certain areas.

Note: The minimum impedance for bridged channels is 8 ms. Also, p se oh lea

observe t pr he oper speaker wiring when bridging channels. Input selection and

volume settings for br idged channels will be controlled by the left channel. “BR” is

bridged mode and “ST” is non-bridged or stereo mode.

Input Selection Switch

Each channel is capable of delivering the source from many inputs. The three main

inputs are BUS 1, BUS 2 and LINE IN. The selection for these inputs is done via the

Input Selection switch associated with each channel. Select the desired source input.

Set the Input Selection switch to BUS 1 (will play source connected to the BUS 1

input), BUS 2 (will play source connected to the BUS 2 input) or LINE IN (will play

source connected to that channel’s LINE IN).

Speaker Output Terminals

The AMP800VS uses high quality Phoenix style connectors for the speaker

connections. Use 14-18 gauge stranded two-conductor loudspeaker wire. Ensure that

at least 2 inches of each conductor are separated. Strip away ¼ inch of insulation

from each conductor. Connect the appropriate conductor to each screw terminal,

observing correct polarity. Also, please observe proper speaker wiring when bridging

channels.

Individual Channel Input

All twelve channels have their own dedicated input that allows the connection of

audio sources in addition to the common BUS inputs. This is useful when using the

AMP800VS with an audio matrix switcher.

AC Voltage Switch

The unit is set at the factory for 115V

U.S. operation; simply connect the included IEC

power cord to your wall outlet. F or 230V ope ation,r move the voltage selector s witch to

the 230V position. When operating at 230V the internal fuse located in the IEC

so et should also be changed. In most 230V applications a separate power cord will ck

be required and is not included.

IEC Power Connector

The unit comes with an IEC jack that permits removal of the AC power cord. This

allows the flexibility of changing the power cord for different countries. The IEC so et ck

also houses the main fuse holder. Plug the power cord supplied with the ampliﬁer into

the ampliﬁer and a wall outlet or appropriate surge protector.

CAUTION: DO NOT plug the ampliﬁer’s power cord into a switched outlet, such as

what is provided on some Surround Receivers. If you wish to have the ampliﬁer turn

on when the Receiver is powered up, use one of the power modes, such as Trigger or

Auto.

12.

Produktspecifikationer

Varumärke:	AudioSource
Kategori:	mottagare
Modell:	AMP800VS

Behöver du hjälp?

Om du behöver hjälp med AudioSource AMP800VS ställ en fråga nedan och andra användare kommer att svara dig

Ditt namn*

Din e-post*

Skriv din fråga här

mottagare AudioSource Manualer

AudioSource AMP 50 Bruksanvisning

10 December 2024

AudioSource AMP102 Bruksanvisning

10 December 2024

AudioSource AMP310 Bruksanvisning

10 December 2024

AudioSource AMP310VS Bruksanvisning

10 December 2024

AudioSource AMP102VS Bruksanvisning

10 December 2024

AudioSource AMP210 Bruksanvisning

10 December 2024

AudioSource AMP800VS Bruksanvisning

10 December 2024

AudioSource AMP1200VS Bruksanvisning

10 December 2024

AudioSource AMP100VS Bruksanvisning

10 December 2024

AudioSource AD508 Bruksanvisning

10 December 2024

mottagare Manualer

Nyaste mottagare Manualer

A-NeuVideo ANI-0108POE-AU Bruksanvisning

11 December 2024

Jensen XDA95RB Bruksanvisning

11 December 2024

AVMATRIX SD1121-12G Bruksanvisning

11 December 2024

AVMATRIX SD1191 Bruksanvisning

11 December 2024

ButtKicker BKA1000-P Bruksanvisning

11 December 2024

Phonic NT2504 Bruksanvisning

11 December 2024

Phonic DMA8825 Bruksanvisning

11 December 2024

Phonic MAX 1000 Bruksanvisning

11 December 2024

Phonic XP 5000 Bruksanvisning

11 December 2024

Phonic Xtrix 4100 Bruksanvisning

11 December 2024