Bellman Visit Bruksanvisning

Bellman Säkerhet Visit

Läs nedan 📖 manual på svenska för Bellman Visit (4 sidor) i kategorin Säkerhet. Denna guide var användbar för 6 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF
Sida 1/4
Buttons and controls
In the box
BE1560 Visit wrist receiver
BE1570 Charger
Elastic wrist band
Power supply
Power and battery
Mains power: 7.5 V DC/1500 mA
Power consumption
Receiver: Active: 100 mA, Idle: 3 mA
Charger: Active: 650 mA, Idle: 70 mA
Battery power
Receiver: 11.2 V V40H rechargeable
Charger: 41.2 V NiMH rechargeable
Operating and charging time
Receiver: ~30 h, Charging time: ~8 h
Charger: Battery charging time: ~24 h
Environment
For indoor use only
Operating temperature
15° to 35° C, 59° to 95° F
Relative humidity
15% to 90%, non-condensing
Frequency and coverage
Radio frequency
314.91 MHz, 433.92 MHz or 868.30
MHz, depending on the region
Coverage
50 – 250 m, 55 - 273 yd. depending
on the radio frequency and the
characteristics of the building
Accessories
BE1270 Bed shaker
BE9086 External trigger cable
Dimensions and weight
Receiver Charger
Height 49 mm 100 mm
Width 38 mm 95 mm
Depth 12 mm 117 mm
Weight 27 g 185 g
Visit LEDS
The Visit LEDs normally indicates
the following:
Orange LED, pacier symbol
The baby monitor is activated
Green LED, door symbol
The door transmitter is activated
Yellow LED, telephone symbol
The phone transmitter is activated
Red LED, re symbol
The smoke alarm is activated
Technical specications
Visit wrist receiver
Visit LEDs
Silicone wrist band 3.5 mm bed shaker input
Charger Charging LED
BE1270 bed shaker
Function button Mains LED
Bed shaker
test button
Battery LED
Power supply
BE8102
”click”
1 2 3
Getting started
1 Pull the battery tab on the charger and connect the power supply to the mains outlet. The mains LED lights up in green.
Place the wrist receiver in the charger and charge it for at least 2 hours. The charging LED is green during charging.
2 To test the radio link you need a Visit transmitter. Press the test button/s on the transmitter.
3 The receiver starts to vibrate and lights up a Visit LED. If a bed shaker is connected during charging, it will vibrate.
If nothing happens, see Troubleshooting.
Default signal pattern
When a transmitter is activated, the wrist receiver lights up an LED and starts to vibrate with a certain pace. This is called
signal pattern. The transmitters determine the pattern, and the default is as follows:
Activated transmitter Wrist receiver LED Wrist receiver / bed shaker vibration
Door transmitter Green Slow
Push button transmitter Green Slow
Telephone transmitter Yellow Medium
Baby monitor Orange Fast
Smoke alarm Red Long
Changing the signal pattern
The signal pattern can only be changed on the transmitters. See Changing the signal pattern for the relevant transmitter.
LED indications
When the wrist receiver battery is nearly depleted, the battery LED starts to blink in yellow. The charging time is up to 8 h.
The charger is equipped with a battery backup and the charger LEDs indicate the following:
LED Indication Status
Charging LED Green light The receiver battery is being charged.
Mains LED Green light The charger is powered by mains voltage.
Mains LED Green blinks The charger is powered by the battery backup.
Visit wrist receiver
Changing the radio key
If your Visit system is activated for no reason, there is probably a nearby system that triggers yours. In order to avoid radio
interference, you need to change the radio key on all units. The radio key switches are located on the transmitters.
Here is how you change the radio key:
1 Open the transmitter cover and move any radio key switch to the up (on position) to change
the radio key. See Changing the radio key for the relevant transmitter.
2 Press and hold the function button on the wrist receiver until the green and yellow Visit LEDs
blink alternately. Release the button.
3 Press the test button/s on the transmitter within 30 seconds to send the new radio key.
4 All Visit LEDs on the receiver blink 5 times to show that the radio key has been changed. It then returns to normal mode.
Note: All Visit units must be set to the same radio key in order to operate as a group.
1 2 3 4
5
Visit wrist receiver
Accessories
The wrist receiver can be complemented with the following accessory:
BE1270 Bed shaker
Wakes you with vibrations if anything happens while
you are asleep. Connect it to the charger and slide it
under your pillow or mattress.
Note: The bed shaker only works when the wrist receiver
is placed in the charger. The receiver will not vibrate
during charging, but the Visit LEDs will act as usual.
Press the bed shaker test button on top of the charger to
try the bed shaker vibration.
On
O
Warning! The wrist receiver and charger can ONLY USE RECHARGEABLE NiMH BATTERIES. Non-
rechargeable batteries will start to leak during charging and the battery acid will damage the electronics
in the wrist receiver and charger. The resulting damage is not covered by warranty.
BE1270

Produktspecifikationer

Varumärke: Bellman
Kategori: Säkerhet
Modell: Visit

Behöver du hjälp?

Om du behöver hjälp med Bellman Visit ställ en fråga nedan och andra användare kommer att svara dig


Säkerhet Bellman Manualer

Bellman

Bellman BE1442 Bruksanvisning

14 September 2024
Bellman

Bellman Visit Bruksanvisning

12 September 2024
Bellman

Bellman BE1289 Bruksanvisning

11 September 2024

Säkerhet Manualer

Nyaste Säkerhet Manualer

Honeywell

Honeywell Galaxy G3 Bruksanvisning

24 Oktober 2024
Abus

Abus fubw50020 Bruksanvisning

22 Oktober 2024
Honeywell

Honeywell HRGX85X Bruksanvisning

21 Oktober 2024
Alphatronics

Alphatronics AlphaVision NG Bruksanvisning

20 Oktober 2024
Aritech

Aritech SHATTERPRO 3 Bruksanvisning

20 Oktober 2024
Axis

Axis Camera Station S9001 Mk II Desktop Terminal Bruksanvisning

19 Oktober 2024
Eminent

Eminent EM6511 Bruksanvisning

18 Oktober 2024
Eminent

Eminent EM6104 Bruksanvisning

18 Oktober 2024
Hikvision

Hikvision DS-2CD2232 Bruksanvisning

18 Oktober 2024
NetworX

NetworX NX-595E IP Communication Module Bruksanvisning

5 Oktober 2024