CRUX AMP-CH5 Bruksanvisning

CRUX Inte kategoriserad AMP-CH5

Läs nedan 📖 manual på svenska för CRUX AMP-CH5 (4 sidor) i kategorin Inte kategoriserad. Denna guide var användbar för 4 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF
Sida 1/4
AMP-CH5
OEM Amplier Replacement Interface for
Chrysler, Dodge, Jeep & RAM Vehicles with Uconnect Systems
R
INTERFACING SOLUTIONS
- Retains U-Connect and navigaon prompts.
- Retains Bluetooth handsfree mode.
- Allows adjustments for Balancing/Fading, Bass, Mid and Treble frequencies.
- Retains OEM radio EQ controls.
- Adjustable bass frequency and level. Includes an under dash mount encoder/bass knob.
- Provides 4 channel Front/Rear outputs plus non-fading subwoofer output.
- Remote output to turn on aermarket amplier.
- Includes an OEM amplier Bypass harness. No cung of factory wires.
PRODUCT FEATURES:
PARTS INCLUDED:
Crux Interfacing Solutions • 21541 Nordhoff St., Unit C, Chatsworth, CA 91311
phone: (818) 609-9299 • fax: (818) 996-8188 • www.cruxinterfacing.com
1 of 4 rev.092519
PRODUCT OVERVIEW:
The AMP-CH5 allows for an improvement in audio quality in vehicles equipped with data-bus controlled amplied
sound systems by upgrading to an aermarket mul-channel amplier while retaining the factory radio. The
AMP-CH5 provides balance, fader, bass, mid and treble frequency adjustments as well as a non-fading subwoofer
output for opmum sound staging.
NOTE:
AMP-CH5 Module AMP-CH5 Harness
OEM Amp Bypass Harness AMP-CH5 Encoder/Bass Knob
Audio from the factory backup sensors is not retained.
1. Carefully remove the trim bezel
around the radio and instrument
cluster. Use a plasc pry tool and go all
the way around the trim to pop up the
clips.
2. Remove the 4 screws holding
the screen.
3. Unplug the 52-pin connector
behind the screen.
6. Find a suitable locaon to mount
the aermarket amplier(s). You
will need to run the following to the
aermarket amplier:
1) Power wires from the baery
2) An amp turn-on wire and RCA
cables from the AMP-CH5 module.
3) Speaker wires from the OEM
amplier locaon. OEM amplier
locaon can vary by vehicle. On
sedans and trucks, it is usually
located on the le boom side of
the dashboard. On SUVs in the cargo
area. Make sure you have enough
length wires and RCA cables.
4. Plug the 52-pin connector to the
mang connector on the AMP-CH5
T-harness.
5. Plug the other end of the
AMP-CH5 T-harness to the OEM
screen.
7. On a 2017 Dodge Charger, the OEM
amplier is at the le boom side
of the dashboard. Remove the panel
above the pedals by removing the
panel clips.
8. Locate the OEM amplier and
unplug the connectors.
9. Connect the speakers wires from
the aermarket amplier to the Amp
Bypass harness included in the kit.
Mate the connectors into the OEM
amplier harness connectors.
R
INTERFACING SOLUTIONS
AMP-CH5
OEM Amplier Replacement Interface for
Chrysler, Dodge, Jeep & RAM Vehicles with Uconnect Systems
INSTALLATION INSTRUCTIONS:
Crux Interfacing Solutions • 21541 Nordhoff St., Unit C, Chatsworth, CA 91311
phone: (818) 609-9299 • fax: (818) 996-8188 • www.cruxinterfacing.com
2 of 4 rev.092519
R
INTERFACING SOLUTIONS
AMP-CH5
OEM Amplier Replacement Interface for
Chrysler, Dodge, Jeep & RAM Vehicles with Uconnect Systems
10. Plug the RCAs to the AMP-CH5
module.
11. Plug the 20-pin AMP-CH5
T-harness connector and the RJ11
encoder/bass knob connector to
the AMP-CH5 module.
12. Complete the connecons on the
aermarket amplier and mount the
amplier.
Crux Interfacing Solutions • 21541 Nordhoff St., Unit C, Chatsworth, CA 91311
phone: (818) 609-9299 • fax: (818) 996-8188 • www.cruxinterfacing.com
3 of 4 rev.092519
14. Encoder/Bass Knob Funcons:
- Press to turn ON/OFF Loudness funcon
- Turn to adjust subwoofer level
- Press and hold to enter programming mode
15. For vehicle specic wiring connecons of the OEM
Amp Bypass Harness, please visit
hps://www.cruxinterfacing.com/lisngs/amp-ch5/ or
scan the QR code:
13. Mount the encoder/bass knob to
the desired locaon.
R
INT ERFACIN G S OLUT ION S
Gold Series
To Vehicle
Harness
To Headunit
Aftermarket Amplier
22 Pin White
16 Pin Black
10 Pin Gray
To
OEM
Amplier
Harness
Encoder /
Bass Knob
Visit www.cruxinterfacing.com/????
for vehicle specic wiring instructions
of the OEM Amplier Bypass Harness
Front
Rear
Sub
Amp Turn On
(use to prevent turn on pop)
INSTALLATION DIAGRAM:

Produktspecifikationer

Varumärke: CRUX
Kategori: Inte kategoriserad
Modell: AMP-CH5

Behöver du hjälp?

Om du behöver hjälp med CRUX AMP-CH5 ställ en fråga nedan och andra användare kommer att svara dig


Inte kategoriserad CRUX Manualer

CRUX

CRUX SOOGM-16 Bruksanvisning

26 September 2024
CRUX

CRUX DKGM-16W Bruksanvisning

26 September 2024
CRUX

CRUX DKVW-52B Bruksanvisning

26 September 2024
CRUX

CRUX DKVW-52 Bruksanvisning

26 September 2024
CRUX

CRUX ACP-MAX Bruksanvisning

26 September 2024
CRUX

CRUX RFM-MG1 Bruksanvisning

26 September 2024
CRUX

CRUX SOCGM-18L Bruksanvisning

26 September 2024
CRUX

CRUX SWRGM-49L Bruksanvisning

26 September 2024
CRUX

CRUX WVICH-03M Bruksanvisning

26 September 2024
CRUX

CRUX WVIFD-02F Bruksanvisning

26 September 2024

Inte kategoriserad Manualer

Nyaste Inte kategoriserad Manualer

Philips

Philips 43PUL7672 Bruksanvisning

27 Oktober 2024
Manhattan

Manhattan 461504 Bruksanvisning

27 Oktober 2024
Sungrow

Sungrow SG125HV Bruksanvisning

27 Oktober 2024
Schneider

Schneider CCT724319 Bruksanvisning

27 Oktober 2024
Technoline

Technoline WS 250 Bruksanvisning

27 Oktober 2024
Livarno

Livarno IAN 354423 Bruksanvisning

27 Oktober 2024
Kupper

Kupper 12152 Bruksanvisning

27 Oktober 2024
JennAir

JennAir CARBON24L Bruksanvisning

27 Oktober 2024
Medion

Medion Life E74001 (MD 81035) Bruksanvisning

27 Oktober 2024
POLARIS

POLARIS Sportsman Touring 850 SP (2015) Bruksanvisning

27 Oktober 2024