CRUX VIMPR-90 Bruksanvisning

Läs nedan 📖 manual på svenska för CRUX VIMPR-90 (1 sidor) i kategorin Inte kategoriserad. Denna guide var användbar för 2 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Sida 1/1
TO FACTORY
HARNESS
8-PIN
(male plug)
8-PIN
(male plug)
INTERFACE
8-PIN
(female plug)
GREEN/ VDO UNLOCK
WHITE/ 12V OUTPUT
4 5 6
TO ENABLE VIDEO
IN-MOTION 1. On = Enable
2. Not Used
3. Not Used
4. Not Used
5. Not Used
6. Not Used
ON
1 2 3
1 2 3
4 5 6
7 8 9
0
TUNER CD
MAIN AUDIO SOUND TEL MAIL INFO TRIP NAVIAV
REPEAT
20-PIN
(female plug)
20-PIN
(male plug)
SAFETY WARNING:
THIS INTERFACE IS DESIGNED TO ACTIVATE
VIDEO IN-MOTION TO ALLOW THE PASSENER
ACCESS TO THE ADDRESS INPUT WHILE THE
VEHICLE IS IN-MOTION. THIS INTERFACE MAY
CAUSE AN ERROR WHEN SERVICED AT THE
OEM DEALER. BE AWARE THAT MOST DEALERS
WILL ATTEMPT TO VOID THE MANUFACTURERS
WARANTY WHEN INSTALLING ANY AFTER-
MARKET EQUIPMENT. IMPROPER USE OF THIS
INTERFACE BY THE DRIVER MAY RESULT IN
CITATION. DRIVER MUST KEEP FULL ATTENTION
ON THE ROAD AND RESPOSIBILITY ON THE
SAFETY OF HIS PASSENGERS.
INTERFACI NG SOLUTIONS
VIDEO IN-MOTION ACTIVATION FOR PORSCHE w/NAVIGATION PCM 2.1
PORSCHE:
2005 - 2008 Cayenne (E1)
Important Note:
This interface only supports the
following radio types:
- PCM 2.1
VIMPR-90 We recommend reading this installation guide rst before starting any
work. Following these instructions from “Start” to” Finish” will ensure
a smooth and hassle free installation. We oer telephone support M-F
9:00 AM – 5:00PM PDT at 1 (855) 822-1348. We are here to help.
PARTS INCLUDED:
(1) PR-90 Interface
(1) PR-90 Harness
(1) Instruction
PRECAUTIONS:
- Remove the negative side of the battery to avoid any short circuits
durring the installation.
- Do not install the interface near any major components or near the
HVAC system. This may cause damage or overheating to the vehicle.
- Do not disconnect the airbag connection behind the radio panel.
PRELIMINARY:
Please read the entire mannual before installing this interface.
Vehicle must be equipped with factory DVD changer.
This interface does not activate DVD reader.
INSTALLING THE INTERFACE:
1. Remove the factory radio to gain access to the factory connectors.
2. Make the T-Harness connections behind the factory radio.
(if the connectors do not match please contact tech support)
3. Test and make sure the Reverse gear triggers the interface and
also test the video in-motion while the car is rolling.
(Navigation address input should be active while rolling)
4. Make all other connections before re-installing the factory
radio.
INSTALLATION OVERVIEW
TROUBLE SHOOTING
1. No video display while driving.
- Make sure the dip swithces are in the proper location.
Rev. 051613
DIP SWITCH SETTING:
Set dip switch number one to “ON”. (Permanent)
All others are OFF.
NON-PERMANENT VIDEO IN-MOTION:
If the customer wants the option to deactivate the video in-motion.
The installer can use the GREEN wire instead of the dip switch setting
to activate and deactivate the video in-motion.
This way the user can have access to the wire without having to get
behind the radio if eanting to deactivate.

Produktspecifikationer

Varumärke: CRUX
Kategori: Inte kategoriserad
Modell: VIMPR-90

Behöver du hjälp?

Om du behöver hjälp med CRUX VIMPR-90 ställ en fråga nedan och andra användare kommer att svara dig




Inte kategoriserad CRUX Manualer

Inte kategoriserad Manualer

Nyaste Inte kategoriserad Manualer