CRUX DKGM-48D Bruksanvisning

CRUX Inte kategoriserad DKGM-48D

Läs nedan 📖 manual på svenska för CRUX DKGM-48D (4 sidor) i kategorin Inte kategoriserad. Denna guide var användbar för 5 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF
Sida 1/4
- Retains factory features in select GM Class II Data Bus vehicles while functioning with an
aftermarket radio.
- Pre-programmed to retain factory Steering Wheel Controls.
- Voice Recognition Command from factory SWC.
- Supports Bose, Y-91 and non-amplified audio systems.
- Retains chime functions.
- Built-in chime volume adjustment.
- Double DIN Dash Kit included.
- EIA color coded wiring for easy installation.
GM- D Module 48
GM- D Harness (GM-C2) 48
SWC Cables
Double DIN Dash Kit
1. The Front and Rear fading are not retained on Y-91 Bose System.
2. Chime includes: seat belt, check engine, key in ignition, low fuel, low oil and lights on.
rev.092821
1/4
SETTING THE AFTERMARKET RADIO BRAND
With the key in the off position, set the DIP switches to the corresponding radio listed below. See page 4 for SWC
button functions.
3.5MM SWC CABLE
The SWRGM- D Module allows for both types of connections: 48
OPTION A is used for ALPINE, CLARION, JVC, and KENWOOD units (Blue/Yellow wire is attached)
is used for BOSS, DUAL, FAHRENHEIT, JENSEN, PIONEER, POWER ACOUSTIK, SONY & OPTION B
SOUND STREAM units.
NOTE: Cap or insulate the 3.5mm plug or Blue/Yellow wire if not being used.
If the vehicle is equipped with a Bose system, the DKGM- D has a built-in Bose adaptor that allows the proper audio 48
input gain from the aftermarket radio to the Bose amplifier. To use this feature, plug in the male 8-pin connector on
the harness to the GRAY female 8-pin connector on the GM- D 48 module. The module is also labeled “Bose” and
“Non Bose” to avoid confusion. (see picture below)
If the vehicle is NOT equipped with a Bose system, plug in the male 8-pin connector to the BLACK female 8-pin on
the GM- D module. 48
2/4
BOSE
Connection
Non-BOSE
Connection
rev.092821
The - D has a potentiometer to adjust the chime volume. It is set at half way by default. To adjust the DKGM 48
volume, simply use a suitable screwdriver and turn the potentiometer clockwise to increase the volume and
counter-clockwise to decrease the volume.
Dash Kit Assembly
Please make sure that you have all the parts shown below.
(1) Main trim ring
(1) Left ISO mounting bracket
(1) Right ISO mounting bracket
3/4
rev.092821

Produktspecifikationer

Varumärke: CRUX
Kategori: Inte kategoriserad
Modell: DKGM-48D

Behöver du hjälp?

Om du behöver hjälp med CRUX DKGM-48D ställ en fråga nedan och andra användare kommer att svara dig


Inte kategoriserad CRUX Manualer

CRUX

CRUX SOOGM-16 Bruksanvisning

26 September 2024
CRUX

CRUX DKGM-16W Bruksanvisning

26 September 2024
CRUX

CRUX DKVW-52B Bruksanvisning

26 September 2024
CRUX

CRUX DKVW-52 Bruksanvisning

26 September 2024
CRUX

CRUX ACP-MAX Bruksanvisning

26 September 2024
CRUX

CRUX RFM-MG1 Bruksanvisning

26 September 2024
CRUX

CRUX SOCGM-18L Bruksanvisning

26 September 2024
CRUX

CRUX SWRGM-49L Bruksanvisning

26 September 2024
CRUX

CRUX WVICH-03M Bruksanvisning

26 September 2024
CRUX

CRUX WVIFD-02F Bruksanvisning

26 September 2024

Inte kategoriserad Manualer

Nyaste Inte kategoriserad Manualer

Philips

Philips 43PUL7672 Bruksanvisning

27 Oktober 2024
Manhattan

Manhattan 461504 Bruksanvisning

27 Oktober 2024
Sungrow

Sungrow SG125HV Bruksanvisning

27 Oktober 2024
Schneider

Schneider CCT724319 Bruksanvisning

27 Oktober 2024
Technoline

Technoline WS 250 Bruksanvisning

27 Oktober 2024
Livarno

Livarno IAN 354423 Bruksanvisning

27 Oktober 2024
Kupper

Kupper 12152 Bruksanvisning

27 Oktober 2024
JennAir

JennAir CARBON24L Bruksanvisning

27 Oktober 2024
Medion

Medion Life E74001 (MD 81035) Bruksanvisning

27 Oktober 2024
POLARIS

POLARIS Sportsman Touring 850 SP (2015) Bruksanvisning

27 Oktober 2024