CRUX SWRSU-38A Bruksanvisning

Läs nedan 📖 manual på svenska för CRUX SWRSU-38A (3 sidor) i kategorin Inte kategoriserad. Denna guide var användbar för 6 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Sida 1/3
Crux Interfacing Solutions • 21541 Nordhoff St., Unit C, Chatsworth, CA 91311
phone: (818) 609-9299 • fax: (818) 996-8188 • www.cruxinterfacing.com
rev.031220
SWRSU-38A
Radio Replacement with Steering Wheel Control Retention for
Select SUBARU Vehicles 2007 - 2009
1 of 3
RADI O REPLAC EMEN T
SWC R ETENT IO N
+
R
INTERFACING SOLUTIONS
- Retains factory features in select Subaru vehicles while funconing with an aermarket radio.
- Pre-programmed to retain factory Steering Wheel Controls.
- EIA color coded wiring for easy installaon.
PRODUCT FEATURES:
PARTS INCLUDED:
SWRSU-38A Module SWRSU-38A T-Harness SWC Cable
INSTALLATION DIAGRAM:
AFTERMARKET
RADIO
4-Pin
Connector
Cap or insulate if
not being used
Kenwood/JVC (BLUE / YELLOW)
Insulate with tape
if not being used
3.5MM SWC CABLE
Plug in the 3.5MM SWC cable to the 4-pin port
on the module. See “DIP SWITCH SETTINGS” section.
ON RADIO VEHICLE
1 2 3 4 5 6 7 8
+12V Constant Yellow
+12V ACC Red
Ground Black

Antenna Power Blue








TO FACTORY
HARNESS
12-Pin Black
Connector
AFTERMARKET
RADIO SELECTOR
(See Page 2)
SUBARU
SWC SETTING
(See Page 2)
ON RADIO VEHICLE
1 2 3 4 5 6 7 8
8 Pin Connector
14 Pin Connector
Crux Interfacing Solutions • 21541 Nordhoff St., Unit C, Chatsworth, CA 91311
phone: (818) 609-9299 • fax: (818) 996-8188 • www.cruxinterfacing.com
rev.031220
SWRSU-38A
Radio Replacement with Steering Wheel Control Retention for
Select SUBARU Vehicles 2007 - 2009
2 of 3
RADI O REPLAC EMEN T
SWC R ETENT IO N
+
R
INTERFACING SOLUTIONS
DIP SWITCH SETTINGS:
SUBARU STEERING WHEEL CONTROL DIP SWITCH SETTING:
AFTERMARKET RADIO DIP SWITCH SETTINGS:
NOTE: Insulate the Blue/Yellow and Green wires if not being used.
RADIO BRAND: DIP: 1 2 3 4
Atoto, Dual, Farenheit, Jensen, Pioneer
Power Acoustik, Soundstream
Blaupunkt, Most o-brand Radios
Alpine
Clarion
Kenwood
JVC
Boss, Old Sony
New Sony
OFF OFF ON ON
OFF OFF ON ON
OFF OFF ON ON
OFF OFF OFF OFF
OFF ON ON OFF
OFF ON ON ON
OFF ON OFF ON
OFF ON OFF OFF
OFF OFF ON OFF
SWC MODULE
ON RADIO VEHICLE
1 2 3 4 5 6 7 8
NOTE: For Atoto, Blaupunkt, Dual, Farenheit, Power Acoustik, Soundstream, and most o-brand radios,
check the aftermarket radio’s manual to see if the SWC buttons need to be programmed.
3.5MM SWC CABLE
Plug in the 3.5MM to 4-Pin SWC cable to the SWC module.
INSTALLATION INSTRUCTIONS:
1. Carefully remove the gear shier
trim ring.
2. Use a plasc pry bar and carefully li
and remove the gear shier trim bezel.
3. Unplug the cigaree lighter
connecon.
DIP: 5 6 7 8
Panasonic made Radio
Clarion made Radio*
Clarion made Radio**
Fujitsu Ten made Radio
ON OFF OFF ON
OFF ON OFF ON
ON OFF ON OFF
OFF ON OFF ON
SWC MODULE
ON RADIO VEHICLE
1 2 3 4 5 6 7 8
RED to SWC Key 1
WHITE to SWC Key 2
SHIELD to SWC Ground
For aermarket radios that have wires for SWC connecons, cut o the 3.5mm plug on the Crux SWC Cable (opon B) and
connect the SWC wires as follows:
Note that there are some radios that only have
SWC1 and SWC2, in this case shield” does not
need to be connected.
Crux Interfacing Solutions • 21541 Nordhoff St., Unit C, Chatsworth, CA 91311
phone: (818) 609-9299 • fax: (818) 996-8188 • www.cruxinterfacing.com
rev.031220
SWRSU-38A
Radio Replacement with Steering Wheel Control Retention for
Select SUBARU Vehicles 2007 - 2009
3 of 3
RADI O REPLAC EMEN T
SWC R ETENT IO N
+
R
INTERFACING SOLUTIONS
4. Remove the screws holding the le
and right side trims.
5. Remove the le and right side trims. 6. Remove the screws holding the
radio.
7. Unplug the hazard light connector. 8. Unplug the connectors behind the
radio.
9. Note that the SWC connecon is
made on the 8-pin connector.
8. Use the necessary dash kit (not included) to complete the installaon. Connect
the aermarket radio wires to the SWRSU-38A T-harness.
9. Plug in the SWRSU-38A 8-pin SWC connector to the factory mate.
10. Conrm the DIP Switch sengs and test the steering wheel controls for
funconality.
11. Test the radio for other funconality before installing the new radio into the
dash. Reverse the radio removal process.
VEHICLE APPLICATIONS:
SUBARU
2007-2009
2007-2009
Legacy (without Automac Climate Controls)
Outback (without Automac Climate Controls)

Produktspecifikationer

Varumärke: CRUX
Kategori: Inte kategoriserad
Modell: SWRSU-38A

Behöver du hjälp?

Om du behöver hjälp med CRUX SWRSU-38A ställ en fråga nedan och andra användare kommer att svara dig




Inte kategoriserad CRUX Manualer

Inte kategoriserad Manualer

Nyaste Inte kategoriserad Manualer