Electro-Voice MB200 Bruksanvisning

Electro-Voice Inte kategoriserad MB200

Läs nedan 📖 manual på svenska för Electro-Voice MB200 (4 sidor) i kategorin Inte kategoriserad. Denna guide var användbar för 6 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF

Sida 1/4

# of Enclosures # of Kits Req’d

in Array: Mb200 Mb300

2 2 1

3 3 2

4 4 3

5 5 4

6 (complete circle) 6 6

Description

The Mb200 installation kit consists of a

U-bracket, two M8 x 1.25 hex-head bolts,

four lock washers, two friction pads, and two

3/8-24 hex-head bolts (see Chart 1). The kit

is designed to accommodate the System

200TM installation in a variety of ways.

Wall or Ceiling Mounting:

The robust design of the Mb200 installation

bracket allows the System 200TM speakers

to be mounted in almost any position to ob-

tain the desired sound coverage (see Figure

3).

Flying Installations

The Mb200 bracket “captures” the speaker

in a rigid frame which has structurally sound

locations for attaching rigging hardware.

These attachment points are four 12.7-mm

(1/2-in.) diameter holes located on the ends

of the bracket. A 3/8-in. “quick link” (or simi-

lar hardware) can be readily connected to

each attachment point.

System 200TM speakers can be flown indi-

vidually in either a horizontal or vertical po-

sition, or two speakers can be flown together

in a vertical position (see Figures 4 and 5).

System 200TM Horizontal Arrays

Arrays of two to six speakers are securely

supported in a frame comprised of Mb200

and Mb300 brackets. To create a horizontal

array, two Mb200 brackets are simply locked

into the correct alignment position using the

brackets from the Mb300 Horizontal Array

Mb200

And Mb200W

Installation Kit

• Mounting kit for SystemTM 200

speakers

• May be used in conjuction with

OmniMount® Series 100 support

system1

• Versatile design allows the

speaker to be aimed at any angle

from wall or ceiling

• Provides a rigid frame for flying

one or two speakers

• Creates arrays of two to six speak-

ers when used with the Mb300

Horizontal Array Kit

Kit (see Figure 6). The array is extended by

using one additional Mb200 bracket and one

300 kit for each additional speaker. To

complete the circle for a six speaker array,

one additional Mb300 kit is required. Please

refer to Chart 2 to select the exact number of

each kit needed, based on desired array size.

(Note: refer to Mb300 Horizontal Array Kit

engineering data sheet for detailed instruc-

tions on System 200TM horizontal array con-

struction using Mb200 Installation and

300 Horizontal Array Kits.)

Item Description Quanity Part Number

A Bracket 1 71914

B M8 x 1.25 hex head bolt 2 63310

C 5/16 split ring lock washer 2 38144

D 3/8-24 hex head bolt 2 63311

E 3/8 split ring lock washer 2 38834

F Friction washer 2 38829

CHART 2: Kit Requirements for

System 200TM Horizontal

Array Construction

CHART 1: Mb200 Installation Kit Parts List

Mb200/Mb200W Installation Kit

Mb200 SPECIFICATION GRAPHICS

FIGURE 1 —Attaching Mb200 Bracket

to System 200TM Speaker (exploded view)

22.90 in. (582 mm) 0.33 in. (8 mm)

3.69 in. (94 mm)

2.75 in. (70 mm)

8.0 in.

(203 mm)

8.0 in.

(203 mm)

5.0 in. (127 mm)

HOLE PATTERN FOR OmniMount

LOCATED ON BOTH SIDES AND BACK

0.33 in. (8 mm)

0.5 in. (13 mm)

3/8–24

10.87 in. (276 mm)

24.90 in. (632 mm)

Wall Mounting Instructions

CAUTION: Due to the weight of System

200TM speakers, it is imperative that the

Mb200 bracket be properly secured to the

wall or ceiling. The choice of fastener (not

provided with this kit) will be determined

by the material and construction of the

mounting surface.

1. Refer to Figure 1 for the following steps.

2. Remove the paper backing from one of

the friction pads (F) and, making sure the

holes are aligned, attach to the U-bracket (A)

as shown. Attach the second friction pad in

a similar manner.

3. Attach the U-bracket to the wall or ceil-

ing using fasteners (not supplied) that are

suitable for the construction material.

4. Remove the hole plugs from the ends of

the System 200TM

speaker by gently prying

with a small screwdriver.

5. Place one of the smaller lock washers

6. Place the speaker into the U-bracket and

finger tighten the M8 bolts.

7. Rotate the speaker so that the input

panel is accessible and attach the wires to

the input panel.

8. Position the speaker for the desired cov-

erage and gently tighten the M8 bolts until

the speaker will no longer rotate. DO NOT

OVERTIGHTEN.

Note: The 3/8

-24 bolts (D) are used to

lock the speaker parallel to the bracket and

prevent it from being rotated. This is needed

when arraying the speaker for proper align-

ment and when flying in the vertical posi-

tion.

Flying Instructions

NOTE: A maximum of two speakers can

be suspended together vertically using the

Mb200 installation bracket.

1. Refer to Figure 1 for the following steps.

2. Remove the paper backing from one of

the friction pads (F) and, making sure the

holes are aligned, attach to the U-bracket (A)

as shown. Attach the second friction pad in

a similar manner.

3. Remove the hole plugs from the ends of

FIGURE 2 — Mb200 Installation Kit Dimensions

FIGURE 3 — Wall-Mounting a System 200TM

Speaker

Using the Mb200 Installation Kit

1. OmniMount is a registered trademark of OmniMount

Systems, Inc.

Mb200/Mb200W Installation Kit

Mb200/Mb200 Installation Kit

FORCE

5/16

SHOULDER

EYEBOLT

1.00 in. (25 mm)

MAXIMUM

LENGTH

LOCK WASHER

FORCE

CORRECT

INCORRECT

FIGURE 4A — Correct and Incorrect Eyebolt

Orientation

FIGURE 4B — Horizontal Suspension of a

System 200TM Speaker Using

Mb200 Installation Kit (side view)

FIGURE 4C — Horizontal Suspension of a

System 200TM Speaker Using

Mb200 Installation Kit

(isometric view)

FIGURE 5A — Vertical Suspension of a

System 200TM Speaker Using

Mb200 Installation Kit

FIGURE 5B — Vertical Suspension of Two

System 200TM Speakers Using

Mb200 Installation Kit

FIGURE 6A — Frame Structure for Horizontal

Array in Position for Assembly

(comprised of M

b200 and Mb300

brackets)

Mb300

FIGURE 6B — System 200TM Horizontal Array

(assembled)

WARNING:

Suspending any object is potentially dan-

gerous and should be attempted only by

individuals who have a thorough knowl-

edge of the techniques and regulations of

rigging objects overhead. Electro-Voice

sanctions suspending the System 200TM

speakers only when all current national,

federal, state and local regulations are

taken into account. When the System

200TM speaker is suspended, Electro-Voice

strongly recommends that system be in-

spected at least once a year. If any sign of

weakness is detected, corrective action

should be taken immediately.

Produktspecifikationer

Varumärke:	Electro-Voice
Kategori:	Inte kategoriserad
Modell:	MB200

Behöver du hjälp?

Om du behöver hjälp med Electro-Voice MB200 ställ en fråga nedan och andra användare kommer att svara dig

Ditt namn*

Din e-post*

Skriv din fråga här

Inte kategoriserad Electro-Voice Manualer

Electro-Voice MFX-12MC Bruksanvisning

17 Oktober 2024

Electro-Voice OM-1 Bruksanvisning

26 Augusti 2024

Electro-Voice F.01U.353.096 Bruksanvisning

22 Augusti 2024

Electro-Voice MB200 Bruksanvisning

15 Augusti 2024

Electro-Voice F.01U.353.098 Bruksanvisning

11 Augusti 2024

Electro-Voice RE3-ACC-GC3 Bruksanvisning

9 Augusti 2024

Electro-Voice RE3-HHT766M Bruksanvisning

5 Augusti 2024

Electro-Voice EBK-1 Bruksanvisning

4 Augusti 2024

Electro-Voice RE3-ACC-BC2 Bruksanvisning

3 Augusti 2024

Electro-Voice RE3-HHT5205L Bruksanvisning

3 Augusti 2024

Inte kategoriserad Manualer

Nyaste Inte kategoriserad Manualer

Philips 43PUL7672 Bruksanvisning

27 Oktober 2024

Manhattan 461504 Bruksanvisning

27 Oktober 2024

Sungrow SG125HV Bruksanvisning

27 Oktober 2024

Schneider CCT724319 Bruksanvisning

27 Oktober 2024

Technoline WS 250 Bruksanvisning

27 Oktober 2024

Livarno IAN 354423 Bruksanvisning

27 Oktober 2024

Kupper 12152 Bruksanvisning

27 Oktober 2024

JennAir CARBON24L Bruksanvisning

27 Oktober 2024

Medion Life E74001 (MD 81035) Bruksanvisning

27 Oktober 2024

POLARIS Sportsman Touring 850 SP (2015) Bruksanvisning

27 Oktober 2024