Hobbywing XeRun XR10 Pro WP Bruksanvisning
Hobbywing
Radiostyrda leksaker
XeRun XR10 Pro WP
Läs nedan 📖 manual på svenska för Hobbywing XeRun XR10 Pro WP (2 sidor) i kategorin Radiostyrda leksaker. Denna guide var användbar för 5 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare
Sida 1/2
06
1
1. Turn on the transmitter, ensure all parameters (D/R, Curve, ATL) on the throttle channel are at default (100%). For transmitter without
LCD, please turn the knob to the maximum, and the throttle “TRIM” to 0. Please also turn the corresponding knob to the neutral
position. This step can be skipped if the radio's settings are default.
2. Start by turning on the transmitter with the ESC turned off but connected to a battery. Holding the “ON/OFF” button, the RED LED on
the ESC starts to flash (the motor beeps at the same time), and then release the ON/OFF button.
Note: Beeps from the motor may be low sometimes, and you can check the LED status instead.
You must calibrate throttle range when you begin to use a new ESC, the transmitter has been replaced,or the Throttle TRIM have been adjusted, otherwise the ESC cannot work correctly. We strongly
recommend users to use the “Fail Safe” function on the radio system and set (F/S) to “Output OFF” or “Neutral Position”.The throttle calibration steps are below:
3. Set the neutral point, the full throttle endpoint and the full brake endpoint.
• Leave transmitter at the neutral position, press the “ON/OFF” button, the GREEN LED flashes 1 time and the motor beeps 1 time to accept the neutral position.
• Pull the throttle trigger to the full throttle position, press the “ON/OFF” button, the GREEN LED blinks 2 times and the motor beeps 2 times to accept the full throttle endpoint.
• Push the throttle trigger to the full brake position, press the “ON/OFF” button, the GREEN LED blinks 3 times and the motor beeps 3 times to accept the full brake endpoint.
4. The motor can be started 3 seconds after the ESC/Radio calibration is complete.
Press the ON/OFF button.
The Green LED flashes
twice andmotor
emits “Beep-
Beep” tone.
Move the throttle trigger to the
full throttle
Press the ON/OFF button.
The Green LED flashes three
times and motor emits
“Beep-Beep-Beep”
tone.
Move the throttle trigger to the
full brake
With the throttle trigger
in the neutral position
Press the ON/OFF button.
The Green LED flashes
once and
motor emits
“Beep” tone.
08
02
AT T ENT IO N
This is an extremely powerful brushless motor system. For your safety and the safety of those around you, we strongly recommend removing the pinion gear attached to the motor before
performing calibration and programming functions with this system. It is also advisable to keep the wheels in the air when you turn on the ESC.
• 9 select-to-use profiles applicable to all 1/10 RC car racing.
• Excellent waterproof and dustproof performance, fearless of various weather conditions.
• Separate PRG/FAN port is able to power an external fan for maximize cooling performance or connect a LCD program box or OTA Programmer to the ESC.
• Variable frequency regulation of PWM & brake frequencies allows users to precisely regulate the driving & braking forces (of the motors).
• Softening function (HOBBYWING-initiated) for milder or wilder driving control and better driving efficiency.
• Multiple protections: low-voltage cutoff protection, ESC and motor thermal protection, and fail safe (throttle signal loss protection),reverse polarity protection (the external standard cappack will still be damaged
if battery reversal occurs).
• Data logging for recording the maximum ESC/motor temperature, motor RPM, and others in real time.
• Firmware upgrade via Hobbywing multifunction LCD program box or OTA Programmer (item sold separately).
• To avoid short circuits, ensure that all wires and connections are well insulated before connecting the ESC to related devices.
• Ensure all devices in the system are connected correctly to prevent any damage to the system.
• Read the manuals of all the items being used in the build.Ensure gearing,setup,and overall install is correct and reasonable.
• Please use a soldering iron with the power of at least 60W to solder all input / output wires and connectors.
• Do not hold the vehicle in the air and rev it up to full throttle, as rubber tires can “expand” to extreme size or even crack to cause serious injury.
• Stop usage if the casing of the ESC exceeds 90 / 194 as this may cause damage to both the ESC and motor. Hobbywing recommends setting the “ESC Thermal Protection” to 105 / 221 (this refers to the ℃ ℉ ℃ ℉
internal temperature of the ESC).
• The battery must be disconnected after use.There is a small draw even when the system is off,and will eventually fully drain the battery.This may cause damage to the ESC, and will NOT BE COVERED UNDER
WARRANTY.
This ESC provides proportional braking function; the braking effect is decided by the position of the throttle trigger. It sets the percentage of available braking power when full brake is applied. Large amount
will shorten the braking time but it may damage your pinion and spur.
3D. Brake Rate Control
It’s adjustable from 1 to 20 (step: 1), The larger the setting value, the greater the brake rate, that is, the faster the braking. A suitable rate can aid the driver to brake his vehicle correctly. Generally, you can set it
to a high value to have a quick brake response.
3E. Brake Frequency
The brake force will be larger if the frequency is low; you will get a smoother brake force when the value is higher.If set this item to "Customized", then the brake frequency can be adjusted to a variable value
at any 0-100% throttle input, Please choose the frequencies as per the actual test results of your vehicles.
3F. Brake Control
Option 1: Linear
Hobbywing has recommended using this mode under all circumstances. The braking effect is a bit weaker in this mode than in Traditional brake mode, but it’s easy to control and brings great control feel.
Option 2: Traditional
This is a traditional brake method, just like the previous escs, the brake force is stronger.
Option 3: Hybrid
The ESC switches the brake mode between Linear and Traditional as per the vehicle speed to prevent the slide (between tires and track) from affecting the braking effect.
Note: Please select the right mode for your vehicle as per the track condition, motor performance, and etc.
4A. Boost Timing
It is effective within the whole throttle range; it directly affects the car speed on straightaway and turns. The ESC adjusts the timing dynamically as per the RPM (when “Boost Timing Activation” set to “RPM”)
or throttle amount (when “Boost Timing Activation” set to “Auto”) in the operation. The Boost Timing is not constant but variable.
4B. Boost Timing Activation
Option 1: RPM
In RPM mode, the ESC adjusts the Boost Timing dynamically as per the motor speed (RPM). The actual Boost Timing is 0 when the RPM is lower than the Boost Start RPM. The Boost Timing changes as per the
RPM when the RPM change is between the Boost Start RPM and the Boost End RPM. For example, if the Boost Timing is set to 5 degrees and the Boost Start RPM is 10000, the Boost End RPM is 15000. The
Boost Timing corresponds to different RPM is shown below. When the RPM is higher than the Boost End RPM, the actual Boost Timing is the value you had previously set.
1A. Running Mode
Option 1: Forward with Brake
Racing mode. It has only forward and brake functions.
Option 2: Forward/ Reverse with Brake
This option is known to be the “training” mode with “Forward/ Reverse with Brake” functions. The vehicle only brakes on the first time you push the throttle trigger to the reverse/brake position.If the motor stops
when the throttle trigger return to the neutral position and then re-push the trigger to reverse position,the vehicle will reverse,if the motor does not completely stop,then your vehicle won’t reverse but still brake,you
need to return the throttle trigger to the neutral position and push it to reverse again.This method is for preventing vehicle from being accidentally reversed.
Option 3: Forward and Reverse
The motor will reverse immediately when the throttle trigger is pushed to reverse position.This mode is generally used in special vehicles.
1B. Max. Reverse Force
The reverse force of the value will determine its speed. For the safety of your vehicle, we recommend using a low amount.
1C. Cutoff Voltage
Sets the voltage at which the ESC lowers or removes power to the motor in order to either keep the battery at a safe minimum voltage (for LiPo batteries). The ESC monitors the battery voltage all the time, it will
immediately reduce the power to 50% (in 2 seconds) and cut off the output 40 seconds later when the voltage goes below the cutoff threshold. The RED LED will flash a short, single flash that repeats ( , , ) ☆ ☆ ☆
to indicate the low-voltage cutoff protection is activated. Please set the “Cutoff Voltage” to “Disabled” or customize this item if you are using NiMH batteries.
Option 1: Disabled
The ESC does not cut the power off due to low voltage. We do not recommend using this option when you use any LiPo battery as you will irreversibly damage the product. You need to select this option when you
are using a NiMH pack.
Option 2: Auto
The ESC calculates the corresponding cutoff voltage for the battery shall be 7.0V.
Option 3: Customized
The customized cutoff threshold is a voltage for the whole battery pack (adjustable from 3.0V to 7.4V).
1D. ESC Thermal Protection
The output from the ESC will be cut off with the value you have preset.
The GREEN LED flashes ( , , ) when the ESC temperature reaches to the preset value. The output will not resume until the ESC temperature gets down. ☆☆☆
Warning! Please do not disable this function unless you’re in a competition. Otherwise the high temperature may damage your ESC and even your motor.
1E. Motor Thermal Protection
The GREEN LED flashes ( , , ) when the motor temperature reaches to the preset value. The output will not resume until the motor temperature gets down. ☆☆ ☆☆ ☆☆
Warning! Please do not disable this function unless you’re in a competition. Otherwise the high temperature may damage your motor and even your ESC. For non-Hobbywing motor, the ESC ma
get this protection activated too early/late because of the different temperature sensor inside the motor. In this case, please disable this function and monitor the motor temperature manually.
1F. BEC Voltage
BEC voltage can be adjusted between 5.0-7.4V.Set a reasonable value according to the working voltage of the servo.
1G. Smart Fan:
This esc has a fan control function. If this item is set to "Disabled", the fan will continue to run after the ESC is powered on; If this item is set to "Enabled", The fan will start running after the internal temperature
the esc exceeds 50 /122 .℃℉
1H. Remote Off
Option 1: Enabled
Users can simply push and hold the brake trigger for 6 seconds. This option allows the user to turn off the ESC without pushing the ON/OFF button switch.
Option 2: Disabled
Users must turn off the ESC by pressing the ON/OFF switch button from the ESC.
1I. Motor Rotation/Direction
With the motor shaft faces you (the rear end of the motor is away from you), increase the throttle input, the motor (shaft) will rotate in the CCW/CW direction if the “Motor Rotation / Direction” set to “CCW/CW”.
Generally, the vehicle runs forward when the motor (shaft) rotates in the CCW direction. However, some vehicles only run forward when the motor rotates in the CW direction due to the different chassis design. In
that case, you only need to set the “Motor Rotation/Direction” to “CW).
1J. Phase-AC Swap
If the A/C wire of ESC connect to A/C wire of motor with crossed way (A wire of ESC connects to C wire of motor, C wire of ESC connects to A wire), set this item as Enable.
Warning! When #A/#B/#C wire of ESC connect to #A/#B/#C wire of motor correspondingly, do not Set to Enable. Otherwise it will damage the ESC and motor.
2A. Throttle Rate Control
This item is used to control the throttle response. The higher the throttle rate,the more aggressive the throttle will be applied. A suitable rate can help driver to control
the vehicle properly during the starting-up process. Generally, you can set it to a high value to have a quick throttle response if you are proficient at throttle control.
2B. Throttle Curvature
This parameter is used to set the throttle curve.The larger the curvature setting,the more aggressive the throttle will be applied in the previous stage; the smaller the curvature setting,
the softer the throttle will be applied in the previous stage. As shown in the schematic diagram of the curve on the right.
2C. Neutral Range
As not all transmitters have the same stability at “neutral position”, please adjust this parameter as per your preference. You can adjust to a bigger value when this happens.
2D. Initial Throttle Force
It also called as minimum throttle force. You can set it according to wheel tire and traction. If the ground is slippery, please set a small throttle force. Some motors have strong cogging
effect with lower FDR ,if there is any cogging with very light throttle input,you can try to increase the initial throttle force.
2E. Coast
This function allows the motor to naturally and smoothly reduce rpm/speed,and the vehicle will not experience sudden deceleration during the throttle release process.The higher the value,the stronger the "coasting"
feeling.
What is COAST?
When a vehicle has a larger final drive ratio, the tendency of having a “drag” feel is higher. The “COAST” technology is to allow the car to roll (coast) even when the final drive ratio is high. The Coast function
brings better and smoother control feeling to racers. Some drivers will refer to this to the traditional brushed motors.
Note: The Coast setting will not work if the drag brake is not set to 0%.
2F. PWM Drive Frequency
The acceleration will be more aggressive at the initial stage when the drive frequency is low; a higher drive frequency is smoother but this will create more heat to the ESC.If set this item to "Customized", then the
PWM frequency can be adjusted to a variable value at any 0-100% throttle input, Please choose the frequencies as per the actual test results of your vehicles.
2G. Softening Value
It allows users to fine-tune the bottom end, change the driving feel, and maximize the driving efficiency at different track conditions. The higher the "Softening Value ", the softer the bottom end. In Modified
class, drivers often feel the power of the bottom end is too aggressive. Little throttle input usually brings too much power to the car and make it hard to control at the corners, this is HOBBYWING's solution to help
bottom end traction.
You can increase the motor mechanical timing accordingly after you set the softening value. Every time you increase the softening value by 5 degrees, you can increase the mechanical timing by 1 degree. Note:
For example, if you set the softening value to 20 degrees, then you can increase the mechanical timing by 4 degrees. Please note that you will never increase the mechanical timing by over 5 degrees.
2H. Softening Range
It's the range to which "Softening Value” starts and ends. If set to 30% then the softening range will be from 0 throttle to 30% throttle.
3A. Drag Brake
It is the braking power produced when releasing from full speed to neutral position. This is to simulate the slight braking effect of a neutral brushed motor while coasting. It’s not recommended for buggy and
monster truck.
(Attention! Drag brake will consume more power and heat will be increased, use it cautiously.)
3B. Drag Brake Rate
This parameter is used to control the speed of the drag-brake response. Setting a suitable value can improve the drag braking effect of the vehicle, thus, improving drivability to suit each users. The value can
be adjusted up to 20 levels. Increasing the value will result in a greater drag brake effect. The other "Auto" option is available as well to choose from. “Auto” will intelligently adjust the drag brake acceleration
according to the current speed. The faster the current speed, the smaller the drag brake rate, vice versa.
3C. Max. Brake Force
01
CAUT IO NS
Thank you for purchasing this HOBBYWING product! Please read this
declaration carefullybefore use, once you use the product,we will assume
that you have read and agreed with all the content.Brushless power systems
can be very dangerous and any improper use may cause personal injury and
damage to the product and related devices, so please strictly follow the
instruction during installation and use.Because we have no control over the
use,installation, or maintenance of this product, no liability may be assumed
for any damages or losses resulting from the use of the product. We do not
assume responsibility for any losses caused by unauthorized modifications to
our product. We have the right to modify our product design, appearance,
features and usage requirements without notification. We, HOBBYWING,
are only responsible for our product cost and nothing else as result of using
our product.Regarding the possible semantic different between two
different versions of declaration, for users in mainland China, please take
the Chinese version as standard; for users in other regions, please take the
English version as standard.
AT T ENT IO N
1. Motor Connetion
Sensored motor connection MUST connect A from the ESC to A on the motor, B to B, and C to C, with the sensor wire connected any variation of the motor to ESC connections may cause damage.
Note: If the motor direction is reversed, change the parameter item “Motor Rotation” to achieve the correct setting.
2. Receiver Connetion
The throttle control cable on the ESC has to be plugged into the throttle (TH) channel on the receiver. The throttle control cable has an output voltage of 5-7.4V to the receiver and steering servo, hence, no
separate battery can be connected to the receiver. Otherwise, your ESC may be damaged.If additional power is required, disconnect the red wire on the throttle plug from the ESC.
3. Battery Connetion
Proper polarity is essential. Please ensure positive (+) connects to positive (+), and negative (-) connects to negative (-) when plugging in the battery! When reverse polarity is applied to the ESC from the
battery, the external standard cappack will be damaged.
Note: Item 4C (Boost Start RPM) & item 4D (Boost End RPM) are not programmable if item 4B (Timing Activation) is set to “Auto”.
2
3
Short press the power button to turn on the ESC in the off state, and long press the power button to turn off the ESC.
Attention! To prevent accidental shutdown in racing, pressing the power button cannot shut down the esc while the motor is running,if there is an emergency, battery plugs can be pulled out to turn off the ESC.
03
04
05
Option 2: Auto
In Auto mode, the ESC adjusts the Boost Timing dynamically as per the throttle amount. Only at full throttle, the actual Boost Timing is the value you had previously set.
4C. Boost Start RPM
This item defines the RPM at which Boost Timing is activated. For example, when the Boost Start RPM is set to 5000, the ESC will activate the corresponding Boost Timing when the RPM goes above 5000.
The specific value is determined by the Boost Timing and the Boost End RPM you had previously set.
4D. Boost End RPM
This item defines the RPM at which Boost Timing (you specifically set) is applied. For example, when Boost Timing is set to 10 degrees and the Boost End RPM to 15000, the ESC will activate the Boost Timing
of 10 degrees when the RPM goes above 15000. The ESC will adjust the Boost Timing accordingly as per the actual RPM when the RPM goes below 15000.
5A. Turbo Timing
This item is adjustable from 0 degree to 64 degrees, the corresponding turbo timing (you set) will initiate at full throttle. It’s usually activated on long straightaway and makes the motor unleash its maximum potential.
5B. Turbo Delay
When “TURBO DELAY” is set to “INSTANT”, the Turbo Timing will be activated right after the throttle trigger is moved to the full throttle position. When other value(s) is applied, you will need to hold the
throttle trigger at the full throttle position (as you set) till the Turbo Timing initiates.
5C. Turbo Increase Rate
This item is used to define the “speed” at which Turbo Timing is released when the trigger condition is met. For example, “3 degs/0.1sec” refers to the Turbo Timing of 3 degrees that will be released in 0.1
second. Both the acceleration and heat is higher when the “Turbo increase rate” is of a larger value.
5D. Turbo Decrease Rate
After the Turbo Timing is activated and the trigger condition turns to not be met (i.e. vehicle slows down at the end of the straightaway and gets into a corner, full throttle turns to partial throttle, the trigger
condition for Turbo Timing turns to be not met), if you disable all the Turbo Timing in a moment, an obvious slow-down like braking will be felt and cause the control of vehicle to become bad. If the ESC can
disable the Turbo Timing at some “speed”, the slow-down will be linear and the control will be improved.
Warning!Boost Timing & Turbo Timing can effectively improve the motor efficiency; they are usually used in competitions. Please take some time to read this manual and then set these two items carefully,
monitor the ESC & motor temperatures when you have a trial run and then adjust the Timing and FDR accordingly as aggressive Timings and FDR may cause your ESC or motor to be burnt.
• The RED LED turns on solid and the GREEN LED dies out when the throttle trigger is in the throttle neutral zone. The RED LED will blink meet the Zero Timing competition rules. if the total value of Boost
Timing and Turbo timing is 0.
• The RED LED dies out and the GREEN LED blinks when your vehicle runs forward. The GREEN LED turns solid when pulling the throttle trigger to the full (100%) throttle endpoint.
• The RED LED dies out and the GREEN LED blinks when you brake your vehicle. The GREEN LED turns solid when pushing the throttle trigger to the full brake endpoint and setting the “maximum brake force”
to 100%.
• The RED LED dies out, the GREEN LED blinks when you reverse your vehicle. The GREEN LED turns solid when pushing the throttle trigger to the full brake endpoint and setting the “reverse force” to 100%.
3. When Some Protection is Activated
• The RED LED flashes a short, single flash and repeats “ , , ” indicating the low voltage cutoff protection is activated.☆☆☆
• The GREEN LED flashes a short, single flash and repeats “ , , ” indicating the ESC thermal protection is activated.☆ ☆ ☆
• The GREEN LED flashes a short, double flash and repeats “ , , ” indicating the motor thermal protection is activated.☆☆ ☆☆ ☆☆
• The RED & GREEN LEDS flash a short, single flash and repeats “ , , ” at the same time indicating the drive mode has been automatically switched to sensorless mode from senored mode because of ☆☆☆
abnormal sensor signal when pairing the ESC with a sensored motor.
RPM (Motor Speed)
Actual Boost Timing
<10000
0 Degree
10001-11000
1 Degree
11001-12000
2 Degrees
12001-13000
3 Degrees
13001-14000
4 Degrees
14001-15000
5 Degrees
>15000
5 Degrees
6
5
External Programming
Port for Connecting
Program Card or OTA
Programmer.
In order to make one firmware applicable to all different racing conditions, there are nine “easy-to-select” preset modes (as shown below). Users are able to change the settings of the modes provided (and
rename those modes) as per the control feel, track, and etc. For example, the name can be changed from “Modify” to “TITI2019_MOD_4.5” to indicate the race was ran with a 4.5T motor at 2019 TITC. This can
be saved for future reference as well.
Mode #
1
2
3
4
5
6
7
8
9
Modes/Profiles
Zero Timing
TC-Modify
Buggy-2WD-Modify
Bubby-4WD-Modify
Practice
OpenBL-13.5T
OpenBL-17.5T
SCT-4 Pole
Drift 2WD Carpet
Applications
All Stock racing requiring users to use Zero timing (/blinky) program on their ESCs.
Modify class of 1/10 touring car racing
Modify class of 1/10 2WD buggy racing
Modify class of 1/10 4WD buggy racing
(With Reverse function activated,) practice and sport
13.5T Open Stock class of 1/10 touring car racing
17.5T Open Stock class of 1/10 touring car racing
1/10 short course truck using 4 pole motor
1/10 drift 2WD car on Carpet
Preset Modes for Different Racing:
4
07
Note: The recommended T counts are only applicable with the standard 3650/540 size (3 slot 2 pole) motors when ESCs are in blinky mode.
USER MANUAL
XERUN XR10 Pro-WP
Brushless Electronic Speed Controller
SHENZHEN HOBBYWING TECHNOLOGY Co., LTD. · 101-402 Building 4, Yasen Chuangxin Hi-tech Industrial Park, 8 Chengxin Road, Baolong Industrial Town, Longgang District, Shenzhen, China. February 27, 2024
20240227 HW-SMA540DUL00
Cont./Peak Current
Motor Type
Applications
160A/1200A
Sensored / Sensorless Brushless Motors
1/10 Touring&Buggy racing, 1/10 Drift,F1,Rally
Motor Limit
Model XERUN XR10 Pro-WP
LiPo Cells
BEC Output
Cooling Fan
Size
Weight
Programming Port
2S LiPo (Only 2S)
5-7.4V Adjustable, Continuous Current of 5A (Switch-mode)
Powered by the stable BEC voltage of 5-7.4V
37.7x37.2x19.6mm (w/o Fan)
95.6g (w/ wires)
PRG/FAN Port
Touring Car 4.5T Buggy 5.5T:≥ :≥
Parameter ValuesSection Item Programmable Items
Forward and ReverseForward/ Reverse with Brake
General SettingThrottle ControlBrake ControlTiming
1A Running Mode Forward with Brake
3.0-7.4V Adjustable (Step: 0.1V)Auto (3.5V/Cell)1C Cutoff Voltage Disabled
75%50%1B Max. Reverse Force 25% 100%
125 /257℃℉
105 /221℃ ℉1D ESC Thermal Protection Disabled
3%-10% Adjustable (Step: 1%)2C Neutral Range
1-15 Adjustable (Step: 1)2D Initial Throttle Force
HybridTraditional3F Brake Control Linear
Auto
4B Boost Timing Activation RPM
4K2K
2F PWM Drive Frequency 1K
1F BEC Voltage 5.0V-7.4V Adjustable (Step:0.1V)
2A Throttle Rate Control 1-30 Adjustable (Step: 1)
2E Coast 0%-15% Adjustable (Step: 1%)
2G Softening Value 0-30° Adjustable (Step: 1°)
3A Drag Brake Force 0%-100% Adjustable (Step: 1%)
3B Drag Brake Rate Auto 1-20 Adjustable (Step: 1)
3C Max. Brake Force 0%-150% Adjustable (Step: 1%)
4A Boost Timing 0-64° Adjustable (Step: 1°)
4C Boost Start RPM 500-35000RPM (Step: 500RPM)
5A Turbo Timing 0-64° Adjustable (Step: 1°)
4D Boost End RPM 3000-60000RPM (Step: 500RPM)
3D Brake Rate Control 1-20 Adjustable (Step: 1)
125 /257℃℉
105 /221℃ ℉1E Motor Thermal Protection Disabled
Enabled1G Smart Fan Disabled
EnabledRemote Off Disabled
CW1I Motor Rotation CCW
Enabled1J Phase-AC Swap Disabled
Customized2B Throttle Curvature -10~10 Adjustable (Step: 1)
1H
8K 12K 16K 24K 32K Customized
2K1K3E Brake Frequency 0.5K 4K 8K 12K 16K
20%10%2H Softening Range 0% 25% 30% 35% 40% 45% 50% 55% 60% 65% 70% 75%
0.1s0.05s5B Turbo Delay Instant 0.15s 0.2s 0.25s 0.3s 0.35s 0.4s 0.45s 0.5s 0.6s 0.7s 0.8s 0.9s 1.0s
5C Turbo Increase Rate Instant
Instant
30deg/0.1s
30deg/0.1s
1deg/0.1s 2deg/0.1s 3deg/0.1s 5deg/0.1s 8deg/0.1s 12deg/0.1s 16deg/0.1s 20deg/0.1s 25deg/0.1s
1deg/0.1s 2deg/0.1s 3deg/0.1s 5deg/0.1s 8deg/0.1s 12deg/0.1s 16deg/0.1s 20deg/0.1s 25deg/0.1s5D Turbo Decrease Rate
Customized
• Restore the default values with a multifunction LCD program box pro
After connecting the program box to the ESC, Click on Parameter Settings and select the Reset Parameters to restore the factory settings.【 】 【 】
• Restore the default values with a OTA Programmer (& HW Link App)
After connecting the OTA Programmer to the ESC, open the HOBBYWING HW Link App on your smart phone, select “Parameters” followed by “Factory Reset” to reset the ESC.
1. Program your ESC with a multifunction LCD program box pro
Connect the interface marked with "- + " on the esc to the interface marked with "ESC" on the program box using a separate programming cable(a cable with JR plugs at both ends included in the program
box packaging), then connect the esc to the battery and turn it on. Click on Parameter Settings to set the esc.【 】
2. Using the OTA Programmer for parameter settings
Insert the programming cable of the OTA Programmer into the programming interface of the esc, and use your phone to install the HW Link APP to set the esc.
3. Read the running data of esc
1) Click on the Data record on the homepage of the LCD box pro to read the five extreme values of the highest temperature of the esc, the highest temperature of 【 】
the motor, the maximum current, the lowest voltage of the battery, and the highest rpm of the motor during the operation of the esc.
2) By using the OTA Bluetooth module, you can view the five extreme values recorded above, real-time data, and historical data (curve chart) under the Data Log【 】
menu in the HW LINK App on your phone.
4. Upgrade of firmware for esc
1) Using the LCD box pro or OTA programmer, download and install the HW LINK App on your phone,click on the Firmware Update button on the APP 【 】
homepage to upgrade the firmware of the esc.
2) Connect to the computer through the LCD box pro, download and install Hobbywing USB LINK software on the computer, and use this software to
upgrade the firmware for esc.
Trouble SolutionsPossible Causes
1. No power was supplied to the ESC;
2. The ESC switch was damaged.
The throttle cable of the esc is connected incorrectly
or the throttle is not at the neutral position.
The default/popular motor rotation direction does not match
your car frame.
1. The receiver was influenced by some foreign interference;
2. The ESC entered the LVC protection;
3. The ESC entered the thermal shutdown protection.
1. The throttle neutral position on your transmitter
was actually in the braking zone;
2. Set the “Running Mode” improperly;
3. The ESC was damaged.
1. The (ESC-to-motor) wiring order was incorrect
2. Some soldering between the motor and the ESC was not good;
3. The ESC was damaged (some MOSFETS were burnt).
Check if all ESC & battery connectors have been well soldered or
firmly connected.
1. Plug the throttle cable into the throttle channel (CH2) by referring to
relevant mark shown on your receiver.
2. Calibrate the esc and radio.
Adjust the parameter "Motor Rotation".
1. Check all devices and try to find out all possible causes, and check the
transmitter’s battery voltage;
2. The RED LED keeps flashing indicating the LVC protection is activated,
please replace your pack;
3. The GREEN LED keeps flashing indicating the thermal protection is
activated, please let your ESC cool down before using it again.
1. Recalibrate the throttle neutral position;
2. Set the “Running Mode” to “Fwd/Rev with Brk “;
3. Contact the distributor for repair or other customer service.
1. Check the wiring order;
2. Check all soldering points, please re-solder if necessary;
3. Contact the distributor for repair or other customer service.
1. Change another pack with great discharging capability;
2. Change a low-speed motor, or increase the FDR;
3. Set the Throttle Rate Control to a low level.
1. Check if the sensor cable is loose or poor contact issue exists;
2. Hall sensor inside the motor or the ESC is damaged.
After power on, the RED LED flashes
and the motor does not work.
The vehicle is going in the reversed direction
when the forward throttle is applied.
The ESC was unable to start the status LED, the
motor, after it was powered on.
The motor stuttered but couldn’t start.
The vehicle could run forward (and brake),
but could not reverse.
The motor got stuck or stopped when increasing
the throttle during the starting-up process.
The RED & GREEN LEDS on the ESC flashed rapidly
at the same time when the throttle trigger was at
the neutral position.
The motor suddenly stopped or significantly
reduced the output in operation.
1. Poor discharging capability of the pack;
2. The RPM of the motor was too high, or the FDR
was too low;
3. The Throttle Rate Control is set too high.
(When pairing with a sensored motor) the ESC
automatically switched to sensorless mode
when it detected incorrect signal from Hall sensor.
Diagram of Throttle Curvature
Output
Power
Throttle
Throttle Curvature 0=
Throttle Curvature 0>
Throttle Curvature 0<
Release the
ON/OFF button
once the RED
LED flashes.
Hold the ON/OFF
button
Battery
Electronic Speed Controller
Receiver
Motor
Orange (C)
Blue (A)
Sensor port of motor
Sensor wire
Switch
Yellow (B)
Produktspecifikationer
Varumärke: | Hobbywing |
Kategori: | Radiostyrda leksaker |
Modell: | XeRun XR10 Pro WP |
Behöver du hjälp?
Om du behöver hjälp med Hobbywing XeRun XR10 Pro WP ställ en fråga nedan och andra användare kommer att svara dig
Radiostyrda leksaker Hobbywing Manualer
26 September 2024
26 September 2024
26 September 2024
26 September 2024
26 September 2024
26 September 2024
26 September 2024
26 September 2024
26 September 2024
25 September 2024
Radiostyrda leksaker Manualer
- Radiostyrda leksaker ACME
- Radiostyrda leksaker Absima
- Radiostyrda leksaker Spektrum
- Radiostyrda leksaker Chicco
- Radiostyrda leksaker Carson
- Radiostyrda leksaker Amewi
- Radiostyrda leksaker Proline
- Radiostyrda leksaker Biltema
- Radiostyrda leksaker DJI
- Radiostyrda leksaker Little Tikes
- Radiostyrda leksaker Revell
- Radiostyrda leksaker Futaba
- Radiostyrda leksaker Tamiya
- Radiostyrda leksaker Traxxas
- Radiostyrda leksaker ARRMA
- Radiostyrda leksaker Spin Master
- Radiostyrda leksaker Graupner
- Radiostyrda leksaker Blade
- Radiostyrda leksaker ParkZone
- Radiostyrda leksaker JETI
- Radiostyrda leksaker Ninco
- Radiostyrda leksaker Multiplex
- Radiostyrda leksaker SkyRC
- Radiostyrda leksaker SAB
- Radiostyrda leksaker Ripmax
- Radiostyrda leksaker Maverick
- Radiostyrda leksaker Reely
- Radiostyrda leksaker Robbe
- Radiostyrda leksaker LRP
- Radiostyrda leksaker Lenoxx
- Radiostyrda leksaker Axial
- Radiostyrda leksaker FMS
- Radiostyrda leksaker E-flite
- Radiostyrda leksaker Flyzone
- Radiostyrda leksaker FrSky
- Radiostyrda leksaker Jada
- Radiostyrda leksaker HPI Racing
- Radiostyrda leksaker Kyosho
- Radiostyrda leksaker Hobby Zone
- Radiostyrda leksaker JR
- Radiostyrda leksaker RC4WD
- Radiostyrda leksaker Sky Rider
- Radiostyrda leksaker DF-Models
- Radiostyrda leksaker ROCHOBBY
Nyaste Radiostyrda leksaker Manualer
27 Oktober 2024
27 Oktober 2024
27 Oktober 2024
26 Oktober 2024
19 Oktober 2024
15 Oktober 2024
8 Oktober 2024
4 Oktober 2024
3 Oktober 2024
3 Oktober 2024