IFi Audio Go blu Bruksanvisning

IFi Audio mottagare Go blu

Läs nedan 📖 manual på svenska för IFi Audio Go blu (2 sidor) i kategorin mottagare. Denna guide var användbar för 6 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF

Sida 1/2

7. Factory Reset

System reset (long press ≥3s).

8. USB-C input

The USB-C socket isn’t just a charging port, it plays up to 24 bit

96kHz directly from USB input. It will take <40 minutes for a high-

powered US B charger to fully charge GO blu. Use the enclosed

USB 'Type A' to 'Type C' cable, smart charger or a regular charger

up to 6.3V.

Note: To switch the audio source from B luetooth to USB, please stop music playback and

disconnect the GO blu from the Bluetooth source. Connect the USB-C input (8) to the U SB audio

source via a USB cable and selec t the GO blu as the playback device.

To switch from USB to Blue tooth transmission, disconnect the GO blu from the audio device

and reconnect the Bluetooth device.

The default setting of the phone does not allow charging of the GO blu (except in exclusive mode).

Tip: Exclusive mode is when the device outputs only the sound of the currently used application. Only

a few applications have an exclusive mode setting; in general there is no difference to charging the

GO blu between turning exclusive mode on or off. However some applications allow charging with

exclusive mode on.

9. LED for Battery Status

LED Status

Green* > 60%

Yellow* 10% >

Red* 10% ≤

*Battery LED will flash when it is charging and will go out when it is fully charged.

10. Microphone

Built-in mic for hands-free calls when paired with your smartphone.

Tip: To wake up your phone's voice assistant, long-press the multi-function knob.

Note: Current instructions apply to firmware version 3.05 and higher.

Tip: For the required driver and all the latest firmw are updates please visit our website:

www.ifi-audio.com/download-hub/ ifi-audio.com Ver1.3

Digital filters

To enter/exit filter selection mode, short-press button (1) three

times, a beep will sound, then press button (3) to selec t filter. See

item (4) for digital filter mode LED colours.

"STD" Standard, modest filtering, modest pre and post ringing

"MIN" Minimum phase, slow roll-off, minimum pre and post ringing

2. Multi-function knob

Controls:

- Volume control (turn)

- Play/Pause (a short click)

- Skip forward (two short clicks)

- Skip back (three short clicks)

- Wake up voice assistant (long press)

Answer the phone:

- Answer the call (short press)

- Hang up (long press)

3. Settings, Bluetooth pairing, Voice alert on/off,

Digital filter mode and restore factory settings

This button cycles between (Please refer to item 4):

Off XBass X Space XBass + XSpace (short press) > > >

Pairing (long press ≥ 3s, indicator flashes red/blue)

Restore factor y settings (press and hold for ≥ 15s, indicator

flashes white 3 times)

4. Sound effects and Bluetooth status LED

The LED colour scheme indicates the current sound effects and

Bluetooth status of GO blu.

LED Mode

Yellow XBass

Cyan XSpace

White XBass + XSpace

Off -

Bluetooth

LED Status

Off Wireless Bluetooth (Connected)

Blue (flashing) Wireless Bluetooth (Awaiting connection)

Blue/Red (flashing) Wireless Bluetooth (Pairing)

Pairing

From switch on, the GO blu will blink blue as it searches for a previously paired device. If a stored

device is not found, it will automatically enter pairing mode and blink blue/red.

To enter pairing mode, long-press button (3) until Bluetooth Mode LED flashes blue / red. To pair,

look for ‘GO blu’ in the list of available Bluetooth devices on your phone.

The GO blu is able to store up to 8 paired Bluetooth devices.

Digital filter

LED Mode

Green STD

Magenta MIN

Note: Short press the power button 3 times to enter the digital filte r mode adjustment, then

short press the filter mode selection button (3) to change the digita l filter type. Short press

the power button 3 times again to kee p the current selection and exit the digital filter

selection mode (it will beep). It will also e xit the filter mode and retain the filter selected if

no butto n is pressed for 30 seconds.

45 6

Specications

Chipset: Qualcomm QCC 5100 Series

Input: USB-C

Bluetooth 5.1 ( AAC, SBC, aptX, aptX HD,

aptX Adaptive, aptX LL, LDAC, LHDC/HWA Codec)

Power System: Charging via USB-C, BC V1.2 compliant up to

1000mA charging current and 6.3 volts

Headphone Outputs:

Balanced: 4.4mm

UnB AL: 3.5mm

Power Output:

Balanced: 245mW @ 32Ω; 5.6V @ 600Ω

UnB AL: 165mW @ 32Ω; 2.8V @ 600Ω

Output Impedance:

Balanced: <1Ω

UnB AL: <1Ω

SNR:

Balanced: 111dBA

UnB AL: 106.5dBA

DNR: 120dB(A) (BAL/UnBAL)

THD + N:

Balanced: <0.009% (6.5mW/2.0V @ 600Ω)/

UnB AL: <0.03% (100mW/1.27V @ 16Ω)

Frequency Response: 20Hz - 45kHz (-3dB)

Battery: Lithium-polymer 450mAh approx. ~10 hours

Dimensions: 54 x 34 x 13 mm

2.1" x 1.3" x 0.5”

Net weight: 27 g (0.95 oz)

Warranty period: 12 months

*Specications are subject to cha nge without notice.

8 9 10

1. Power on/off, Bluetooth format annunciation,

Voice alert on/off and digital filter mode on/off

Power switch

Long press and hold the power switch for ≥ 3s to power on/off the GO blu.

Bluetooth format annunciation

Press the power switch twice and the voice will announce the

Bluetooth format you are currently receiving.

Voice annunciation on/off

In the shutdown state, first press the Bluetooth pairing key (3)

without releasing it, and then press the power key to turn it on.

The operation method of turning off and turning on voice

annunciation is the same.

Note: After turning off the voice annunciation, the c urrent B luetooth format and sampling

freque nc y will no longer be announced.

1 2 3

Restore factory settings

LED Status

White Restore factory settings

Note: You need to use the factory reset in the power-on state, during which no other operations

can be performed; when the factory reset is successful, the white light will flash 3 times with a

beep sound. After the operation is successful, the device will be in the power-on state.

Warning: Restoring the factory settings will clear all the memorized Bluetooth addresses, XBass

and XSpace will be turned off, and voice (decoding format) announcement will be turned on.

5. Balanced 4.4mm headphone output

Connect balanced 4.4mm headphones.

6. S-Balanced 3.5mm headphone output

Connect 3.5mm headphones.

Produktspecifikationer

Varumärke:	IFi Audio
Kategori:	mottagare
Modell:	Go blu
Färg på produkten:	Roze
Vikt:	- g
Bredd:	- mm
Djup:	- mm
Höjd:	- mm
Blåtand:	Nee
Skärm diagonal:	7 "
Upplösning:	- Pixels
Processorfrekvens:	- GHz
Intern lagringskapacitet:	8 GB
GPS:	Nee
Plats position:	Nee
Vormfaktor:	Slate
Inkluderar operativsystem:	Android
Plattform:	Android
Maximal videoupplösning:	- Pixels
Internminne:	- GB
Förvarings media:	Flash
Batteritid/batteritid:	- uur
Operativsystem version:	4.2
Typ av enhet:	Mobiele tablet
Tangentbord ingår:	Nee