IOptron MAK150 Bruksanvisning

Läs nedan 📖 manual på svenska för IOptron MAK150 (4 sidor) i kategorin Inte kategoriserad. Denna guide var användbar för 9 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Sida 1/4
iOptron Corporation, 6E Gill Street, Woburn, MA 01801
www.iOptron.com
Electr Focuser for onic
iOptron MAK150 OTA Dual-Speed Focuser
# 8452
Instruction Manual
September 2023 V2 .0
iOptron reserves the rights to revise this instruction without notice. Actual color/contents/design may dier from those described in this instruction.
2
The #8452 ctr Focuser Focuser) is Ele onic (e
designed for iOptron Rumak-type 150mm an
Maksutov-Cassegrain telescope (MAK150) -dual
speed focuser. The eFocuser then can be
controlled by a compatible iOptron mount. It may
work with other scopes use the similar dual-speed
focuser.
Features:
Whisper quiet operation
Powerful stepper motor
Zero backlash
Plug into iOptron Port with no external
power source needed
3 speed control by a compatible iOptron
hand controller
Currently supported mount (with rmware
version V161101 or later ):
CEM26/GEM28
CEM40/GEM45
CEM70
CEM120
CEM25
CEM60
iEQ30 Pro
iEQ45 Pro
Package includes:
1X eFocuser for MAK150
1X Pulley
1X Synchronous belt
1X Control cable
Installation:
1. move both fine tuning and coarse tuning Re
knobs form the dual-speed focuser.
2. Pull the eFocuser out from the cover by remove
three screws.
3. Slide the iOptron eFocuser mounting ring onto
the telescope focusing tube and adjust its
position. Tighten two set screws to lock the E-
Focuser.
3
4. Put the eFocuser pulley onto the dual-speed
focuser ne tuning shaft. Tighten the set screw.
5. Wrap the belt on motor shaft rst. The put it
onto the eFocuser pulley. You may turn the
pulley while install the belt. Adjust the motor
mounting screws to adjust the belt tension if
needed.
6. Put the cover on. Make sure that the cover is
not blocked by the telescope body or dual-
focuser. The ne tuning shaft is sit inside the
small opening. Secure the cover by tightening
three long screws.
7. Connect the eFocuser to the mount use
supplied 6P6C cable (same as the hand
controller cable.) One end to the port on the
eFocuser. The other end to the PORT on an
iOptron mount.
8. Power the mount on. After pass the initial
screen, press MENU on the hand controller and
move the cursor to “Electr ”. Press onic Focuser
ENTER to bring Electr ic Focuser menu. on
Follow the on screen instruction to control the
focuser.

Produktspecifikationer

Varumärke: IOptron
Kategori: Inte kategoriserad
Modell: MAK150

Behöver du hjälp?

Om du behöver hjälp med IOptron MAK150 ställ en fråga nedan och andra användare kommer att svara dig




Inte kategoriserad IOptron Manualer

IOptron

IOptron RC20 Bruksanvisning

25 September 2024
IOptron

IOptron RC10 Bruksanvisning

25 September 2024
IOptron

IOptron HAZ71 Bruksanvisning

25 September 2024
IOptron

IOptron RC6 Bruksanvisning

25 September 2024
IOptron

IOptron RC14 Bruksanvisning

25 September 2024
IOptron

IOptron MAK150 Bruksanvisning

25 September 2024
IOptron

IOptron HAZ46 Bruksanvisning

25 September 2024
IOptron

IOptron RS232 Bruksanvisning

25 September 2024
IOptron

IOptron GEM28 Bruksanvisning

20 September 2024

Inte kategoriserad Manualer

Nyaste Inte kategoriserad Manualer