Jablotron JA-60G Bruksanvisning

Jablotron Säkerhet JA-60G

Läs nedan 📖 manual på svenska för Jablotron JA-60G (1 sidor) i kategorin Säkerhet. Denna guide var användbar för 8 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF

Sida 1/1

The JA-60G Wireless Gas Leak Detector 2 / 2 MEF51311

The JA-60G Wireless Gas Leak Detector

The JA-60G detects mixtures of air and combustible gases or fumes

(Natural Gas, Methane, Propane, Butane).

The mains-powered detector indicates a gas leakage optically, and

acoustically, and transmits alarm signals wirelessly via radio protocol of

Jablotron 6x systems.

Installation

 Installation shall only be undertaken by technicians holding a certificate

issued by an authorized distributor. Warning: this device is connected

to the mains.

 Fix the detector on the wall. For gases lighter than air (natural gas, city

gas etc.) install it close to the ceiling (max. 15 cm under it) or directly on

the ceiling and on the place expected to have gas leakage. For gases

heavier than air (propane, butane, etc.) install it close to the floor or on

the lowest place of the room. The detector should not be located close

to any obstacles preventing natural air circulation.



The detector should not be located close to any obstacles preventing

natural air circulation. It should also not be located in a draft or close to

a cooker (cooking smells and other fumes can have a bad influence on

gas detection)

 Connect the wires, set the detector’s features using its DIP switches

and close its cover.

 Before you connect power, switch the control panel (receiver) to

enrollment mode. The detector transmits enrollment signals when its

power is connected.

ready

green

red

1st level

2nd level

Fig. 1

red

II.

Power terminals

Route the power cable to the terminals marked 230V AC. The power inlet

should be fused with an external fuse (max. 10A). Do not open the detector

cover if the power is on.

Output relay terminals

There is a dry relay switch-over contact available (max. 5A/230V AC)

C - common contact

NO - normally open contact

NC - normally closed contact

This relay output could be used for example to shut down the gas inlet if

there was a gas leak (by means of a suitable electric gas valve).

Warning: The mains relay output does not provide mains isolation for safety!

DIP switches

There are two DIP switches in the detector to set its features:

No. OFF ON

1 relay is triggered if the 1st level of

gas concentration is exceeded relay is triggered if the 2nd level of

gas concentration is exceeded

2 indication of gas leakage will stop

after the concentration drops

down

indication of gas leakage will last

until the detector power is switched

off (memory function)

Function

After switching the power on, the detector transmits its enrollment signal

and the green LED flashes for about 90 seconds while the detector warms

up. When the green LED lights constantly, the detector is ready for operation.

If the gas concentration reaches the 1st level, short beeps sound and the

first red LED lights.

If the gas concentration reaches the 2nd level, long beeps sound and the

second red LED lights.

The output relay reacts depending on DIP switch #1’s setting.

A fire alarm signal is transmitted wirelessly at the same moment as the

detector’s relay reacts (depends on DIP switch #1’s setting).

The JA-60G detector does not regularly check communication with the

control panel (receiver), so the system will not indicate a lost detector during

power dropouts.

Warning - If there is a gas alarm, don’t operate any switches or

electrical devices. Open the windows, and stop the gas leak, if

practical. Call the fire department immediately, but do not use a phone

inside.

LED indicators

Green

 OFF

 flashes

 ON

the gas detector is off

warming up

ready for a gas alarm

Red I.  ON 1st level of gas concentration

Red II.  ON 2nd level of gas concentration

Red II.

Green

 Alternating

flashes sensor error

green LED

red LED

NO 230V

JABLOTRON

JA-60G

REL

AUX

MEM

CACNC

buzzer sensor

Fig. 2

red LED

Maintenance and testing

Keep the detector clean, it is important that its grids should not be blocked

with dust.

Use a gas cigarette lighter without the flame lit, to test the gas detector’s

reaction. The detector will react within 15 seconds.

Professional recalibration of the detector should be done at least every 1

year. Contact your distributor for more details.

Specifications

Sensitivity (gas concentration):

Methane Propane

Level 1 10



3% LEL (0.50% vol. conc.) 18



3% LEL (0.30% vol. conc.)

Level 2 18



3% LEL (0.80% vol. conc.) 30



3% LEL (0.50% vol. conc.)

Iso-butane

Level 1 23



3% LEL (0.30% vol. conc.)

Level 2 40



3% LEL (0.50% vol. conc.)

LEL = Lower Explosive Limit (100 %) according to EN 60079-20-1:

for methane 4,4 % vol. conc., for prophane 1,7 % vol. conc., for iso-buthane

1,3 % vol. conc., calibrated by iso-butane

Power supply 230V(-15% to+10) / 50Hz, 2 W,

protection class II

Detection method hot platinum filament

Buzzer sound level 94dB/0.3m

Relay output optional for 1st or 2nd level, max.230V AC/5A

Alarm memory selectable

Response time 10 s

Warm up time approximately 90 s

Communication band 433.92 MHz

Communication range approx. 50m (open area)

Working environment indoor use, -10 to +40°C, IP30

Complies with EN 50194-1, EN 60079-29-1, EN 50130-4,

EN 55022, EN 60950-1, ETSI EN 300220

For non-explosive areas. Zone 2 according to EN 60079-10.

Can be operated according to ERC REC 70-03

Certified by VVUÚ, cert. body No. 3076

Complies with the essential requirements of: EMC Directive 1999/5/EC

concerning electromagnetic compatibility when used for its intended purpose. The

original of the conformity assessment can be found at www.jablotron.com,

Technical Support section.

Note: Although this product does not

contain any harmful materials we

suggest you return the product to the

dealer or directly to the manufacturer

after use.

Produktspecifikationer

Varumärke:	Jablotron
Kategori:	Säkerhet
Modell:	JA-60G
Färg på produkten:	Zwart
Inbyggd display:	Nee
Vikt:	366 g
Bredd:	178 mm
Djup:	75 mm
Höjd:	26 mm
Förpackningens vikt:	608 g
Förpackningens bredd:	180 mm
Djuppackning:	65 mm
Förpackningshöjd:	230 mm
Användarmanual:	Ja
Husmaterial:	Metaal
Kraftkälla:	DC
LED-indikatorer:	Ja
Typ av förpackning:	Doos
Nuvarande:	3 A
Maximal upplösning:	4096 x 2160 Pixels
Medföljande kablar:	HDMI, IR, USB Type-A to USB Type-B
Inkluderar AC-adapter:	Ja
Ursprungsland:	China
Kod Storbritanniens handelstull:	84718000
Antal USB 2.0-portar:	2
Antal HDMI-portar:	3
DC-spänningsingång:	5 V
Hörlursutgångar:	4
HDCP:	Ja
HDR-stöd:	Ja
Anslutning för nätadapter:	Ja
HD typ:	4K Ultra HD
HDMI-version:	2.0
Plug and play:	Ja
Färgdjup:	32 Bit
Extern anpassning:	Ja
Rackmontering:	Nee
HDCP-version:	1.4/2.2
Videoanslutning:	HDMI
Fjärrkontroll ingår:	Ja
AC-ingångsspänning:	100 - 240 V
AC-ingångsfrekvens:	50/60 Hz
Drifttemperatur (TT):	0 - 45 °C
Relativ luftfuktighet i drift (VV):	10 - 85 procent
Förpackningsvolym:	2691 cm³
Antal mikrofoningångar:	4
Tangentbordsanslutning:	USB
Musanslutning:	USB
Antal datorer:	2
tryckknapp:	Ja
Konsolportar:	3.5mm headphone, 3.5mm mic, HDMI, USB A
Videobandbredd:	60 Hz
Dataöverföringshastighet (max):	18 Gbit/s
Ljudanslutningar:	Ja
Antal USB 3.2-hubportar typ A (3.1 Gen 1):	2
Antal USB 3.2 Gen 1 (3.1 Gen 1) Typ-B-portar:	2
Antal USB-portar på konsolen:	2