Jablotron JA-80E Bruksanvisning

Jablotron Säkerhet JA-80E

Läs nedan 📖 manual på svenska för Jablotron JA-80E (1 sidor) i kategorin Säkerhet. Denna guide var användbar för 3 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF

Sida 1/1

The JA-80E hard-wired keypad 1 / 1 MHE51203

The JA-80E hard-wired keypad

The JA-80E is a component of Jablotron’s OASiS alarm system and is

designed to control and program the system. It has a built-in proximity access

card reader and allows the wiring up of a separate door detector. The keypad

should be wired to the control panel.

Installation

Installation shall only be undertaken by technicians holding a certificate

issued by an authorized distributor. The keypad is for indoor installation only,

typically by a main entrance door.

1. Open the keypad housing (by pressing the tab on the bottom) and

disconnect the inter-housing connection cable inside (by pulling the

connector from the board).

2. Install the rear housing to the desired location.

3. Connect the control panel bus cable. There are two possibilities:

o Use a twisted-pair cable (max. 100m) for keypad installation. The

correspondingly marked terminals in the keypad unit and in the control

panel should be connected together (GND, A, B, +U).

o Use a flat four-cord telephone cable with RJ connectors (max. 10

metres) for temporary (test) installation. There is a digital bus connector

in the control panel, and in the keypad too. The keypad’s digital bus

connector is supplied in the package and must be wired to the circuit

board (remove a blind flange from the rear plastic and route the wires

through the hole).

4. Install the external door detector (if required) and connect its cable to

the IN and GND terminals.

5. Connect the inter-housing cable to the keypad board. Attach the keypad

to the rear housing.

6. Keypad operating instructions are found in the control panel manual.

OASIS 80

A B C

GND

digital bus

cable

OASIS 80

A B C

Keypad menu – language selection and door bell function

If the ∗ key is kept pressed while is being powered-up the internal keypad

menu will be displayed allowing the selection of the desired language. Using

the arrows choose your language and confirm selection by the ∗ key.

In this menu the door bell function can also be enabled or disabled (if

enabled the keypad makes a sound when its IN input is triggered).

To exit the menu, press # (exiting also occurs after 10 seconds’ inactivity).

Notes:

• The keypad power can be switched on by connecting the bus cable or by

switching on the control panel power.

• Each keypad has its own menu, i.e. each keypad in the system can have

its own unique settings.

• The keypad keeps its settings even if its power is disconnected (settings

can only be altered via the keypad menu).

Three minute time-out of displaying the alarm status

To comply with EN standards the keypad does not indicate the status of the

alarm system while the system is set (armed). Indication only returns when the

keypad is operated or an entrance delay is triggered. It is however possible to

program permanent indication via the control panel, if considered appropriate.

Installing a door detector

It is possible to wire up a detector(s) to the keypad via the IN input. The IN

input terminal is triggered when disconnected from GND. The control panel’s

natural reaction to the IN input being triggered is a delayed intruder alarm

(unchangeable reaction).

Notes:

• If the IN input is not used, connect it to GND.

• The IN input only reports to the control panel at the moment of being

triggered (a so-called pulse reaction, which means that the keypad

cannot signal permanently open doors). The input belongs to the C

section (can not be changed) and if there is more than one JA-80E in

the system their inputs IN are not distinguished by the system.

OASIS 80

A B C

ABC

GND

An example of door detector wiring

Disabling the tamper sensor

To disable the tamper sensor, short out the jumper in the keypad unit close

to the tamper sensor (equipped with a spring). This is useful when carrying the

keypad unit around with a long cable while servicing the system. During

normal system use this jumper must remain open circuited

Keypad text editing

There are two kinds of text: device and code names (displayed on the

second line after the address number), and other system text.

The names can be edited via the keypad after pressing and holding the ? key

in service mode – see the control panel installation manual. The edited text is

only stored in the keypad unit used for editing.

If you use a PC running OLink software to set the texts, you will set the texts

in all connected keypads.

If you add a new keypad to the system, you can transfer (synchronize) all the

latest texts to the keypad by using OLink to read the texts from the control

panel. (OLink reading the control panel texts triggers the keypad into listening

in to the bus and copying the texts into itself).

The texts can only be copied into the keypad but cannot be read out of it.

Technical specifications

Power via the control panel bus

Standby consumption 30mA

RFID cards Jablotron PC-01 or PC-02 (EM UNIQUE 125kHz)

Length of digital bus cable max. 100m

Door detector input IN = normally closed loop

Dimensions 113 x 121 x 63 mm

Environment according to EN 50131-1 II. internal

Operating temperature range -10 to +40 °C

EN 50131-1 and CLC/TS 50131-3 classification class 2

FCC ID VL6JA80E

Jablotron Ltd. hereby declares that the JA-80E is in compliance

with the essential requirements and other relevant provisions o

Directive 1999/5/EC and complies with part 15 of the FCC rules.

Operation is subject to the following two conditions: 1. This device

may not cause harmful interference, and 2. This device must

accept any interference received, including interference that may

cause undesired operation.

CAUTION: Changes or modifications not expressly approved by

Jablotron could void the user´s authority to operate the equipment.

The original of the conformity assessment can be found on the web

site www.jablotron.com, Technical Support section.

Note: Although this product

does not contain any harmful

materials we suggest you return

the product to the dealer or

directly to the manufacturer

after use.

Produktspecifikationer

Varumärke:	Jablotron
Kategori:	Säkerhet
Modell:	JA-80E
Enhetsplacering:	Vrijstaand
Typ av operation:	Rotary, Touch
Färg på produkten:	Wit
Dörrgångjärn:	Links
Inbyggd display:	Ja
Vikt:	70300 g
Bredd:	598 mm
Djup:	590 mm
Höjd:	848 mm
Nettoskatt:	2300 W
Typ av laddare:	Bovenbelading
Dörrfärg:	Zwart
Sladdlängd:	1.6 m
Trumminnehåll:	63 l
Fördröjd starttimer:	Ja
Indikering av återstående tid:	Ja
Energie-efficiëntieklasse:	A
Dörröppningsriktning utbytbar:	Nee
Tvätt energiförbrukning:	0.46 kWu
Vattenförbrukning per cykel:	47 l
Centrifuger läkemedelsklass:	B
Ljudnivå (tvätt):	50 dB
Obalans kontrollsystem:	Ja
Maximal centrifugeringshastighet:	1400 RPM
Nuvarande:	10 A
Bulleremissionsklass:	A
Ljudnivå under centrifugering:	71 dB
Cykeltid (max):	213 min
Cykelns längd (snabbtvättprogram):	15 min
Energiförbrukning per 100 cykler:	46 kWu
På-/-Av-knapp:	Ja
Efter typ:	Gehard glas
Djup när dörren är öppen:	1063 mm
AquaStop-funktion:	Ja
Belysning i trumma:	Ja
Displaybelysning:	Ja
Färg på belysningen:	Wit
Öppen dörr:	Opening aan zijkant
Nominell kapacitet:	8 kg
AC-ingångsspänning:	220 - 240 V
AC-ingångsfrekvens:	50 - 60 Hz
Type beeldscherm:	LED
Energieffektivitetsskala:	A tot G
Wasprogramma's:	Black, Blouse/shirt, Colour, Cotton, Delicate/silk, Easy care, Hand/wool, Mix, Outdoor, Rinse, Spin
Färg-på-dörrhandtag:	Zwart
Trumtyp:	Golftrommel
Siemens tvättteknik:	iQdrive