Jensen BUCAM300J Bruksanvisning

Läs nedan 📖 manual på svenska för Jensen BUCAM300J (2 sidor) i kategorin Inte kategoriserad. Denna guide var användbar för 5 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Sida 1/2
Mounting the camera
Look for a locaon that will give you the best view behind the vehicle.This should not be
directly next to or under a reverse/backup lamp as it may blind the camera at night.Avoid
license plate lamps as well as they may blind the camera at night. Before drilling,
determine the best way to run the power wires to the reverse lights & the extension cable
through the car.Insure that your route will not interfere with any safety equipment,trunk
release or other items in the vehicle.Look for wires, sensors,double metal,anything that
could cause a problem or damage.The camera should lay flat against the mounng surface
for proper installaon.
1.Use the included hardware to secure the camera to the vehicle.DO NOT OVERTIGHTEN the hardware.
2.Follow ONE of the following wiring opons.
Oprion 1: Connect camera power wire to the vehicle's reverse lamp:
a)Locate the reverse lamp in the tail light assembly.
b)Aach the red wire to the posive 12 volt wire from the reverse lamp.Use a crimp connector or soldering tool to ensure connecon
is secure. Once this connecon is complete,note that the red power wire that is located on either end of the video RCA cable will not
be needed. The bare wire at the end of each wire lead should be capped or taped off to prevent potenal power interrupon.
c)Aach the black wire to ground(-).
d)Run video cable to the locaon of the receiver or monor(not included).Connect one yellow RCA end of the video cable to the
camera and connect the other end of the yellow RCA cable to the video source(receiver/monitor).
e)Run audio cable to the locaon of the receiver or monor(not included).Connect one black RCA end of the audio cable to the
camera and connect the other end of the back RCA cable to the audio source(receiver/monitor).
Opon 2: Connect camera power wire to receiver/monitor power:
a)From camera locaon,connect red power wire from power cable to red power wire from one end of the video cable.Use a crimp
connector or soldering tool to ensure connecon is secure.
b)Aach the black wire to ground.
c)Run video cable to the locaon of the receiver or monitor(not included).Connect not yellow RCA end of the video cable to the
camera and connect the other end of the yellow RCA cable to the video source(receiver/monitor).
d)From video source(receiver/monitor) locaon,connect red power wire from end of the video cable to the reverse wire lead located
on the video source(receiver/monitor).
e)Run audio cable to the locaon of the receiver or monitor(not included).Connect not black RCA end of the audio cable to the camera
and connect the other end of the black RCA cable to the audio source(receiver/monitor).
Camera Specifications
Image Sensor: CMOS,7440H
Power: 12V DC,Negave Ground
Power Consumpon: 1 Wa
Effecve Pixels: 733H × 493V
Video Format: NTSC
Lux: 0.5
White Balance: Auto
Viewing Angle: 170 Degrees
IP Rang: IP67
Operang Temperature: -30 ~ +70℃ ℃
Camera Body: Zinc Alloy
Microphone Specifications
Audio input
of receiver
Camera input
of receiver
1.6 Ft.
Sensivity: -30±2 dB
Amplifying Power: 0.2 W
S/N Rao(A weighted network): 70(Min) dB
Direconal Characterisc Omni-Direconal
Maximum Input Sound Pressure Level: 100 dB
Waterproof Rang: IP67

Produktspecifikationer

Varumärke: Jensen
Kategori: Inte kategoriserad
Modell: BUCAM300J

Behöver du hjälp?

Om du behöver hjälp med Jensen BUCAM300J ställ en fråga nedan och andra användare kommer att svara dig




Inte kategoriserad Jensen Manualer

Inte kategoriserad Manualer

Nyaste Inte kategoriserad Manualer