Jensen CD1211 Bruksanvisning

Läs nedan 📖 manual på svenska för Jensen CD1211 (20 sidor) i kategorin Inte kategoriserad. Denna guide var användbar för 5 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Sida 1/20
CD1211
Owner's Manual
/
TUNE
CD1211 CD RECEIVER
SCAN
MONO
EQ
AUX IN
AM/FM/CD Receiver
CD1211
2
PREPARATION
Getting Started
Congratulations on your purchase of the Phase
Linear CD1211 Mobile AM/FM/CD Receiver. It’s
a good idea to read all of the instructions before
beginning the installation. We recommend
having your Phase Linear CD1211 installed by
a reputable installation shop.
Contents
Installation Instructions.............................. 3
Wiring ........................................................ 6
Operating Instructions ............................... 7
Tuner Operation ...................................... 10
CD Player Operation ............................... 12
Remote Control ....................................... 14
Care and Maintenance ............................ 15
Troubleshooting....................................... 16
Specifications .......................................... 17
Installation Requirements
This unit is designed for installation in cars,
trucks and vans with an existing radio opening.
In many cases, a special installation kit will be
required to mount the radio to the dashboard.
These kits are available at electronics supply
stores and car stereo specialty shops. Always
check the kit application before purchasing to
make sure the kit works with your vehicle. If you
need a kit but cannot locate one, call our
customer support line at 1-800-323-4815.
(U.S.A. and Canada only.)
Tools and Supplies
The following tools and supplies are needed to
install the radio.
Torx type, flathead and Philips screwdrivers
Wire cutters and strippers
Tools to remove existing radio (screwdriver,
socket wrench set or other tools)
Electrical tape
Crimping tool
Volt meter/test light
Crimp connections
18 gauge wire for power connections
16-18 gauge speaker wire
Speaker Requirements
Only connect speakers rated with a load
impedance of 4 ohms. Speakers with a load
impedance of less than 4 ohms could damage
the unit.
Disconnect Battery
Before you begin, disconnect the battery
negative terminal.
Toll-Free Installation Assistance
If you require assistance, contact Technical
Support at 1-800-323-4815 from 8:30 a.m. to
7:00 p.m. EST Monday through Friday and from
9:00 a.m. to 5:00 p.m. EST on Saturday.
(U.S.A. and Canada only.)
CD1211
3
INSTALLATION INSTRUCTIONS
This unit is designed for installation in cars,
trucks and vans with an existing radio opening.
In many cases, a special installation kit will be
required to mount the radio to the dashboard.
These kits are available at electronics supply
stores and car stereo specialty shops. Always
check the kit application before purchasing to
make sure the kit works with your vehicle.
Pre-installation
1. Disconnect Battery
Before you begin, always disconnect the battery
negative terminal.
2. Remove Transport Screws
Universal Installation Using
Mounting Sleeve
1. Remove the detachable front panel, if it is
attached to the chassis, by pushing the
“Release” button.
2. Slide the mounting sleeve off of the
chassis if it has not already been removed.
If it is locked into position, use the removal
keys (supplied) to disengage it. The
removal keys are depicted on page 5.
3. Check the dashboard opening size by
sliding the mounting sleeve into it. If the
opening is not large enough, carefully cut
or file as necessary until the sleeve easily
slides into the opening. Do not force the
sleeve into the opening or cause it to bend
or bow. Check that there will be sufficient
space behind the dashboard for the radio
chassis.
4. Locate the series of bend tabs along the
top, bottom and sides of the mounting
sleeve. With the sleeve fully inserted into
the dashboard opening, bend as many of
the tabs outward as necessary to firmly
secure the sleeve to the dashboard.
5. Place the radio in front of the dashboard
opening so the wiring can be brought
through the mounting sleeve.
6. Follow the wiring diagram carefully and
make certain all connections are secure
and insulated with crimp connectors or
electrical tape to ensure proper operation.
7. After completing the wiring connections,
attach the front panel and turn the unit on
to confirm operation (vehicle ignition
switch must be on). If the unit does not
operate, recheck all wiring until the
problem is corrected. Once proper
operation is achieved, turn the ignition
switch off and proceed with final mounting
of the chassis.
8. Carefully slide the radio into the mounting
sleeve, making sure it is right-side-up, until
it is fully seated and the spring clips lock it
into place.
/
T
UN E
CD 12 1
1C
DRE CE IVE R
S
CA
N
M
ONO
EQ
AUX
IN
/
TUN E
CD121
1
CDR ECE
I
VE R
S
CA
N
MON
O
E
Q
A
UXIN

Produktspecifikationer

Varumärke: Jensen
Kategori: Inte kategoriserad
Modell: CD1211

Behöver du hjälp?

Om du behöver hjälp med Jensen CD1211 ställ en fråga nedan och andra användare kommer att svara dig




Inte kategoriserad Jensen Manualer

Inte kategoriserad Manualer

Nyaste Inte kategoriserad Manualer