Kicker DX500.1 Bruksanvisning

Kicker bilradio DX500.1

Läs nedan 📖 manual på svenska för Kicker DX500.1 (38 sidor) i kategorin bilradio. Denna guide var användbar för 4 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Sida 1/38
DX AMPLIFIER
D
LIVIN’ LOUD
2011 DX Mono Amps RevI.indd 1
2011 DX Mono Amps RevI.indd 1
2011 DX Mono Amps RevI.indd 1
2011 DX Mono Amps RevI.indd 12011 DX Mono Amps RevI.indd 1 11/3/2010 1:29:20 PM
11/3/2010 1:29:20 PM
11/3/2010 1:29:20 PM
11/3/2010 1:29:20 PM11/3/2010 1:29:20 PM
2
DX.1-SERIES AMPLIFIERS
OWNER’S MANUAL
INSTALLATION
Mounting: Choose a structurally sound location to mount your KICKER amplifi er. Make sure there are no items
behind the area where the screws will be driven. Choose a location that allows at least 4(10cm) of open
ventilation for the amplifi er. If possible, mount the amplifi er in the climate-controlled passenger compartment. Drill
four holes using a 7/64 (3mm) bit and use the supplied #8 screws to mount the amplifi er.
Wiring: Disconnect the vehicle’s battery to avoid an electrical short. Then, connect the ground wire to the
amplifi er. Make the ground wire short, 24(60cm) or less, and connect it to a paint-and-corrosion-free, solid,
metal area of the vehicle’s chassis. Adding an additional ground wire of this same gauge (or larger) between the
batterys negative post and the vehicle chassis is recommended.
PERFORMANCE
Authorized KICKER Dealer:
Purchase Date:
Model Number:
Serial Number:
Model: DX250.1 DX500.1 DX1000.1
RMS Power
@ 14.4V, 4 1% THD+NΩ mono,
@ 14.4V, 2 mono, 1% THD+NΩ
140 x 1
250 x 1
275W x 1
500W x 1
550W x 1
1000W x 1
Length, in. (cm) 10-1/4” (26) 10-1/4” (26) 10-1/4” (26)
Electronic Crossover Fixed, 80Hz
24dB/octave
Variable lo-pass 50Hz–200Hz
18dB/octave
Subsonic Filter Fixed, 25Hz
24dB/octave
Variable hi-pass 10Hz-30Hz
18dB/octave
Bass Boost Selectable, 0/9dB
@ 40Hz
Variable 0–12dB @ 40Hz
Speci cations common to all models:
Height, in. (mm) 2-1/4(57)
Width, in. (mm) 8-5/16” (211)
Frequency Response ± 1dB 20Hz–200Hz
Signal-to-noise Ratio >95dB, A-weighted, re: rated power
Input Sensitivity Low Level: 125mV–5V
High Level: 250mV10V
Remote Bass Yes (not included) Yes Yes
Pro Tip: To get the best performance from your new KICKER Amplifi er and extend the warranty by 1 year, use
genuine KICKER accessories and wiring.
MODEL: DX250.1 / DX500.1 / DX1000.1
2011 DX Mono Amps RevI.indd 2
2011 DX Mono Amps RevI.indd 2
2011 DX Mono Amps RevI.indd 2
2011 DX Mono Amps RevI.indd 22011 DX Mono Amps RevI.indd 2 11/3/2010 1:29:25 PM
11/3/2010 1:29:25 PM
11/3/2010 1:29:25 PM
11/3/2010 1:29:25 PM11/3/2010 1:29:25 PM
3
12V
DX250.1
15A 15A
Model External Fuse
(sold separately)
Power/Ground Wire KICKER Wiring Kit
DX250.1 1 x 40 Ampere 8 Gauge PK8, ZCK84
DX500.1 1 x 80 Ampere 4 Gauge PK4, CK44, ZCK44
DX1000.1 1 x 100 Ampere 4 Gauge PK4, CK44, ZCK44
The DX amplifi er has dual input sensitivity differential RCA inputs which will receive either high or low level signals
from your car stereo’s source unit. A high-level signal can be run from the source unit’s speaker outputs to the
stereo RCA input on the end panel of the amplifi er using the KICKER ZISL as shown (make sure you set the DX
amplifi ers input level switch to “HI”). Alternatively, the signal can be delivered to the amplifi er using the low-level
RCA outputs on the source unit. Set the input level switch on the end panel of the amplifi er to “LO”. Either input
method will provide a low-level output signal at the RCA output, which effectively passes the audio signal to
another amplifi er or component. Keep the audio signal cable away from factory wiring harnesses and other
power wiring. If you need to cross this wiring, cross it at a 90 degree angle.
source unit
high-level speaker
outputs
to amplifi er
shield
+
core conductor
battery
external fuse
remote turn-on
(see page 5)
bare-metal
chassis ground
18”
(45cm)
24”
(60cm)
Install a fuse within 18” (45cm) of the battery and in-line with the power cable connected to your amplifi er. If you
ever need to remove the amplifi er from the vehicle after it has been installed, the ground wire should be the last
wire disconnected from the amplifi er--just the opposite as when you installed it.
KICKER ZISL
source unit high-level
speaker outputs
OR to amplifi er
woofer
MONO OPERATION
minimum impedance of 2 ohms
2011 DX Mono Amps RevI.indd 3
2011 DX Mono Amps RevI.indd 3
2011 DX Mono Amps RevI.indd 3
2011 DX Mono Amps RevI.indd 32011 DX Mono Amps RevI.indd 3 11/3/2010 1:29:26 PM
11/3/2010 1:29:26 PM
11/3/2010 1:29:26 PM
11/3/2010 1:29:26 PM11/3/2010 1:29:26 PM

Produktspecifikationer

Varumärke: Kicker
Kategori: bilradio
Modell: DX500.1

Behöver du hjälp?

Om du behöver hjälp med Kicker DX500.1 ställ en fråga nedan och andra användare kommer att svara dig




bilradio Kicker Manualer

bilradio Manualer

Nyaste bilradio Manualer