Kicker zx 350 2 Bruksanvisning
Läs nedan 📖 manual på svenska för Kicker zx 350 2 (4 sidor) i kategorin bilradio. Denna guide var användbar för 4 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare
Sida 1/4
©2007 Stillwater Designs
ZX
STEREOAMPLIFIER
ZX350.2, ZX450.2, ZX550.2, ZX850.2
+
_
+
+
_
+
_
_
+12V
18"
(45cm)
24"
(60cm)
XOVER
XOVER
XOVER
Installation
1. Mounting Choose a structurally sound location to mount your Kicker amplifi er. Make sure there
are no items behind the area where the screws will be driven. Choose a location that allows at least
4” (10cm) of open ventilation for the amplifi er. If possible, mount the amplifi er in the climate-controlled
passenger compartment. Drill four holes using a 7/64” (3mm) bit and use the supplied #8 screws to
mount the amplifi er.
2. Wiring Disconnect the vehicle’s battery to avoid an electrical short. Then, connect the ground wire to
the amplifi er. Make the ground wire short, 24” (60cm) or less, and connect it to a paint and corrosion free
solid metal area of the vehicle's chassis. Adding an additional ground wire of this same gauge (or larger)
between the battery's negative post and the vehicle chassis is recommended.
The ZX amplifi er has dual input sensitivity differential RCA inputs which will receive either high or low
level signals from your car stereo’s source unit. Ideally, when connecting the source unit to the amplifi er,
the ZX amplifi er’s input level switch should be set to “LO” and a low-level signal should run from the
source unit’s stereo RCA output to the stereo RCA input on the end panel of the amplifi er using RCA
interconnect cable. If a low-level stereo RCA output is not available on the source unit, the signal can
be delivered to the amplifi er using the high-level speaker outputs on the source unit. Set the input level
switch on the end panel of the amplifi er to “HI”. Crimp and solder RCA connectors to the end of the
speaker wire running from the high-level speaker outputs on the source unit and connect the wire to the
RCA Inputs on the end panel of the amplifi er as shown in Figure 1. Either input method will provide a
low-level output signal at the RCA output, which effectively passes the audio signal to another amplifi er
or component. Keep the audio
signal cable away from factory wiring
harnesses and other power wiring. If
you need to cross this wiring, cross it
at a 90 degree angle.
Install a fuse within 18” (45cm) of the battery and in-line with the 8 gauge power cable connected to your
amplifi er. If you ever need to remove the amplifi er from the vehicle after it has been installed, the ground
wire should be the last wire disconnected from the amplifi er--just the opposite as when you installed it.
See the fuse chart on the following page for power and ground wire size, and fusing recommendations.
3. Confi guration The following diagrams show the most common confi gurations for your Kicker ZX
series amplifi er.
ZX.2SeriesAmplifi er
Owner’sManual
Tw o ChannelModels: ZX350.2 / ZX450.2 / ZX550.2 / ZX850.2
Authorized Kicker Dealer:
Purchase Date:
Amplifi er Model Number:
Amplifi er Serial Number:
Congratulations on your
KICKER purchase!
Please record your purchase
information and keep your sales
receipt for validation of warranty.
__________________________
__________________________
__________________________
__________________________
INSTALLATION
2ZX.2AMPLIFIER
CONFIGURATION
3
+12V
18"
(45cm)
24"
(60cm)
+12V
18"
(45cm)
24"
(60cm)
Figure 2
Figure 3
Figure 4
Minimum Impedance of 2 ohms per channel in stereo operation
Minimum impedance of 4 ohms while in bridged operation
Minimum impedance of 4 ohms mono and 2 ohms per channel in stereo simultaneously
Ground
Remote
Turn-On
Fuse
Battery
High Pass
High Pass
Low Pass
Ground
Remote
Turn-On
Fuse
Battery
Ground
Remote
Turn-On
Fuse
Battery
Signal In
Bridge Wiring
Bridge Wiring
Bridged Operation (Mono)
Two Channel Operation (Stereo)
Stereo and Mono Operation Simultaneously (SAMS)
Note: To get the best performance from your new Kicker Amplifi er, we recommend using genuine Kicker Accessories and Wiring.
Performance
Model ZX350.2 ZX450.2 ZX550.2 ZX850.2
RMS Power in Watts, all channels driven
@14.4 Volts, 4Ω stereo, ≤ 1% THD+N 110 x 2 150 x 2 205 x 2 295 x 2
@ 2Ω stereo, ≤ 1% THD+N 175 x 2 225 x 2 275 x 2 425 x 2
@ 4Ω mono, ≤ 1% THD+N 350 450 550 850
Length: in(cm) 13 1/2 (34.2) 16 3/4 (42.5) 20 (50.7) 23 1/4 (59)
Specifi cations common to all models:
Height: in(mm) 2 1/8 (54mm)
Width: in(mm) 9 5/8 (244mm)
Frequency Response, ± 0.5 db: 20 Hz - 20 kHz
Signal-to-Noise Ratio: >95db, a-weighted, re: rated power
Input Sensitivity: Low Level: 125mV-5V
High Level: 250mV-10V
Selectable Electronic Crossover: Variable HI, LO or OFF (bypass), 50 - 200Hz, 12db/Octave
Bass Boost: Variable 0-18db Bass Boost @ 40Hz
+
+
>
+
>
Core Cable
Ground or Shielding
High-level Speaker Output Wire
To Amplifi er
To Source Unit
Figure 1
ModelZX350.2 1 (ONE) 50 AMPERE FUSE PowerGroundWire 8GA
ModelZX450.2 1 (ONE) 60 AMPERE FUSE PowerGroundWire 4GA
ModelZX550.2 1 (ONE) 70 AMPERE FUSE PowerGroundWire 4GA
ModelZX850.2 1 (ONE) 120 AMPERE FUSE PowerGroundWire 2GA
Signal In
Signal Out
Signal In
Signal Out
Signal Out
Operation
1. Automatic Turn-On Selection The ZX series offers three different automatic turn-on modes that can
be selected on the end panel; +12V, DC Offset, and Audio. Using either the DC Offset or Audio mode
causes the REM terminal to have +12V out for turning on additional amplifi ers.
Remote Turn-On Set the switch to +12V to use the remote turn-on lead from your source unit. Run
18 Ga wire from the Remote Turn-On Lead on your source unit to the terminal labeled REM between the
amplifi er’s positive and negative power terminals. This is the preferred automatic turn-on method.
DC Offset Turn-On If Remote Turn-On is not an option, the next best setting is DC Offset. The DC
Offset mode detects a 6 volt surge from the HI Level speaker outputs when the source unit has been
turned on.
Signal Sense Turn-On The Audio setting is the fi nal alternative for Automatic turn-on. This is a Signal
Sense turn-on method that detects the incoming audio signal from your source unit and automatically
turns on the amp. This turn-on method will not work properly if the input gain control is not set
appropriately.
2. Input Level The RCA inputs on Kicker ZX amplifi ers are capable of receiving either Hi or Low-level
signals from your source unit. If the only output available from your source unit is a Hi-Level signal, simply
press in the Input Level switch on the amplifi er. Refer to the wiring section of this manual for additional
instructions.
3. Crossover Switch Use the XOVER switch on the end panel of the amplifi er to set the internal
crossover to OFF, HI or LO. When the switch is set to OFF, a full bandwidth signal will be amplifi ed.
Set the switch to HI if you want the amplifi er’s internal crossover to serve as a high-pass fi lter. Set the
switch to LO if you want the amplifi er’s internal crossover to serve as a low-pass fi lter. Never change the
crossover “OFF/HI/LO” switch setting with the audio system on!
4. Input Gain Control The input gain control is not a volume control. It matches the output of the
source unit to the input level of the amplifi er. Turn the source unit up to about 3/4 volume (if the source
unit goes to 30, turn it to 25). Next, slowly turn (clockwise) the gain on the amplifi er up until you can hear
audible distortion, then turn it down a little.
5. Bass Boost Control The variable bass boost control on the top of the amplifi er is designed to give
you increased output 0 - 18dB at 40 Hz. The setting for this control is subjective. If you turn it up, you
must go back and adjust the input gain control to avoid clipping the amplifi er.
6. Crossover Control The variable crossover on the top of the amplifi er allows you to adjust the
crossover frequency from 50-200Hz. The setting for this control is subjective; 80Hz is a good place to
start.
7. RemoteBass(Level Control) When the crossover
on your ZX.2 series amplifi er is set to LO pass, you
have the ability to control the output level of the
amplifi er remotely. To mount the remote bass level
control, simply screw the metal bracket to the chosen
location. Then slide the housing onto the bracket until
it snaps into place. Run the cable from the controller
to the “Remote Bass” jack on the amplifi er chassis.
Tr o u b l e Shooting
If your amplifi er does not appear to be working, check the obvious things fi rst such as blown fuses,
poor or incorrect wiring connections, incorrect setting of crossover switch and gain controls, etc. There
is an illuminated red badge on top of the amplifi er denoting the power state of the amp in addition to
the Protection LED on the end panel of your Kicker ZX series amplifi er. When the red badge is lit this
indicates the amplifi er is turned on and the amplifi er is functioning properly.
OPERATION
ZX.2AMPLIFIER
4
RED Badge Light off, no output? With a Volt Ohm Meter (VOM) check the following: 1) +12 volt
power terminal (should read +12V to +16V) 2) Remote turn-on terminal (should read +12V to +16V)
3) Check for reversed power and ground connections. 4) Ground terminal, for proper conductivity. 5)
Check for blown fuses.
RED Badge Light on, no output? Check the following: 1) RCA connections 2) Test speaker
outputs with a “known” good speaker. 3) Substitute source unit with a “known” good source unit. 4)
Check for a signal in the RCA cable feeding the amplifi er with the VOM meter set to measure “AC”
voltage.
End Panel LED fl ashing with loud music? The yellow LED indicates low battery voltage. Check
all the connections in your vehicle’s charging system. It may be necessary to replace or charge your
vehicle’s battery or replace your vehicle’s alternator.
End Panel LED on, no output? 1) Amplifi er is very hot. Thermal protection is engaged. Test
for proper impedance at the speaker terminals with a VOM meter (see the diagrams in this manual
for minimum recommended impedance and multiple speaker wiring suggestions). Also check for
adequate airfl ow around the amplifi er. 2) Amplifi er shuts down only while vehicle is running. Voltage
protection circuitry is engaged. Voltage to the amplifi er is not within the 9-16 volt operating range. Have
the vehicle's charging and electrical system inspected. 3) Amplifi er will only play at low volume levels.
Short circuit protection is engaged. Check for speaker wires shorted to each other or to the vehicle
chassis. Check for damaged speakers, or speaker(s) operating below the minimum recommended
impedance.
No output from one channel? 1) Check the balance control on source unit 2) Check the RCA (or
speaker input) and speaker output connections for the channel 3) Swap the RCA (or speaker input)
cable from left to right. If the problem changes sides then you have a bad RCA (or speaker input) cable
or source unit problem. 4) Swap the speaker output wire from left to right. If the problem changes sides
then you have a bad speaker cable, passive crossover network and/or speaker.
Alternator noise-whining sound with engine’s RPM? 1) Check for damaged RCA (or speaker
input) cable 2) Check the routing of RCA (or speaker input) cable 3) Check the source unit for proper
grounding 4) Check the gain settings and turn them down if they are set too high.
Poor stereo image or reduced bass response? Check system phasing by turning the balance
control from left to right. If there is more bass output when turned to either side, then check your speaker
wiring, passive crossover networks and speaker terminals for proper positive and negative connections.
Reverse a speaker connection from positive to negative on the stereo/subwoofer channel(s); if the bass
improves, the speaker was out of phase.
Ground Noise? Kicker amplifi ers are engineered to be fully compatible with all manufacturers’ head
units. Some head units may require additional grounding to prevent noise from entering the audio signal.
If you are experiencing this problem with your head unit, in most cases running a ground wire from the
RCA outputs on the head unit to the chassis will remedy this issue.
Please Note: Modern high performance speakers have a lower DC Resistance than what used to be available. The Kicker
Coaxial and Component speakers are rated at four ohms (some DC Resistances may be as low as 3 ohms) and work with
any amplifi er designed to operate at a four ohm load. If you want to use two Kicker Coaxial or Component speakers on
a single channel of your amplifi er wire the speakers in series. This will improve the sound quality, lower the total harmonic
distortion and lessen the thermal load at the amplifi er. This may prevent an amplifi er from shutting down, due to over-
current protection circuitry.
CAUTION: When jump starting the vehicle, be sure that connections made with jumper cables are correct. Improper
connections can result in blown amplifi er fuses as well as the failure of other critical systems in the vehicle.
If you have more questions about the installation or operation of your new KICKER product, see the Authorized KICKER
Dealer where you made your purchase. For more advice on installation, click on the SUPPORT tab on the Kicker
homepage, www.kicker.com. Choose the TECHNICAL SUPPORT tab, choose the subject you are interested in, and then
download or view the corresponding information. Please E-mail support@kicker.com or call Technical Services (405) 624-
8583 for unanswered or specifi c questions.
PERFORMANCE
5
AUTO
TURN ON INPUT
LEVEL
LRL
INPUT OUTPUT
R
XOVER
SPKR+ SPKR -
SPKR + SPKR -
+12V DC
OFFSET
AUDIO LO
HI
OFF HI LO
REMOTE BASS
Model ZX350.2
110 x 2 @ 4 ohms, 14.4Vdc, 1% THD, CEA-2006 (Watts)
Signal to Noise Ratio -94
CEA-2006 (ref: 1W, A-weighted)
Model ZX550.2
205 x 2 @ 4 ohms, 14.4Vdc, 1% THD, CEA-2006 (Watts)
Signal to Noise Ratio -91
CEA-2006 (ref: 1W, A-weighted)
Model ZX450.2
150 x 2 @ 4 ohms, 14.4Vdc, 1% THD, CEA-2006 (Watts)
Signal to Noise Ratio -91
CEA-2006 (ref: 1W, A-weighted)
Model ZX850.2
295 x 2 @ 4 ohms, 14.4Vdc, 1% THD, CEA-2006 (Watts)
Signal to Noise Ratio -89
CEA-2006 (ref: 1W, A-weighted)
AUTO
TURN ON INPUT
LEVEL
LRL
INPUT OUTPUT
R
XOVER
SPKR+ SPKR -
SPKR + SPKR -
+12V DC
OFFSET
AUDIO LO
HI
OFF HI LO
REMOTE BASS
Slide the housing until it snaps into the metal bracket
4 Conductor
Phone Cable
Back View
Side View
Mount the metal bracket
Produktspecifikationer
| Varumärke: | Kicker |
| Kategori: | bilradio |
| Modell: | zx 350 2 |
Behöver du hjälp?
Om du behöver hjälp med Kicker zx 350 2 ställ en fråga nedan och andra användare kommer att svara dig
bilradio Kicker Manualer
4 Oktober 2024
1 Oktober 2024
29 September 2024
23 September 2024
18 September 2024
16 September 2024
12 September 2024
12 September 2024
12 September 2024
11 September 2024
bilradio Manualer
- bilradio Sony
- bilradio LG
- bilradio AEG
- bilradio Philips
- bilradio Panasonic
- bilradio Daewoo
- bilradio Ford
- bilradio Grundig
- bilradio JVC
- bilradio JBL
- bilradio Kenwood
- bilradio Medion
- bilradio Pioneer
- bilradio Volvo
- bilradio Aiwa
- bilradio Akai
- bilradio Alpine
- bilradio Audison
- bilradio Telefunken
- bilradio Silvercrest
- bilradio Lenco
- bilradio Pyle
- bilradio Manta
- bilradio Caliber
- bilradio Hyundai
- bilradio Renkforce
- bilradio Clatronic
- bilradio Sencor
- bilradio Overmax
- bilradio Blaupunkt
- bilradio Crunch
- bilradio Skoda
- bilradio Denver
- bilradio Stinger
- bilradio Sanyo
- bilradio Hifonics
- bilradio Brigmton
- bilradio Maginon
- bilradio Xomax
- bilradio Rockford Fosgate
- bilradio Marquant
- bilradio Krüger And Matz
- bilradio Audiosonic
- bilradio Clarion
- bilradio Muse
- bilradio Mac Audio
- bilradio Biltema
- bilradio Pure
- bilradio Audiovox
- bilradio Dual
- bilradio Boss
- bilradio Cobra
- bilradio MB Quart
- bilradio Auna
- bilradio Xblitz
- bilradio Tokai
- bilradio Nextbase
- bilradio Boston Acoustics
- bilradio Trevi
- bilradio Orion
- bilradio Magnat
- bilradio Adcom
- bilradio Technaxx
- bilradio Autovision
- bilradio Lanzar
- bilradio Hertz
- bilradio Jensen
- bilradio Roadstar
- bilradio Scott
- bilradio Kunft
- bilradio Ultimate
- bilradio Conceptronic
- bilradio Fusion
- bilradio Revo
- bilradio Elta
- bilradio Axton
- bilradio VDO
- bilradio SPC
- bilradio Soundstream
- bilradio DLS
- bilradio VDO Dayton
- bilradio Macrom
- bilradio Becker
- bilradio Watssound
- bilradio Orava
- bilradio Emphaser
- bilradio Scion
- bilradio US Blaster
- bilradio Eltax
- bilradio RTO
- bilradio Cartronix
- bilradio Spectron
- bilradio Mtx Audio
- bilradio Ground Zero
- bilradio Multilaser
- bilradio ESX
- bilradio RetroSound
- bilradio Lark
- bilradio Planet Audio
- bilradio VW
- bilradio Rodek
- bilradio Toxic
- bilradio Eclipse
- bilradio Voxx
- bilradio SoundMAX
- bilradio Impulse
- bilradio Twister
- bilradio Majestic
- bilradio Mystery
Nyaste bilradio Manualer
27 Oktober 2024
27 Oktober 2024
27 Oktober 2024
27 Oktober 2024
23 Oktober 2024
20 Oktober 2024
20 Oktober 2024
20 Oktober 2024
20 Oktober 2024
20 Oktober 2024