Kicker IX500.4 Bruksanvisning

Kicker bilradio IX500.4

Läs nedan 📖 manual på svenska för Kicker IX500.4 (28 sidor) i kategorin bilradio. Denna guide var användbar för 11 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF
Sida 1/28
IX AMPLIFIER
IX500.4
English Version
Versión Español
Amplificador del la Serie IX.4
Deutsche Version
Stereoverstärker der IX.4-Serie
Version Francaise
Amplificateur de série IX.4
LIVIN’ LOUD
2IX AMPLIFIERS
IX.1-SERIES AMPLIFIERS Owner’s Manual
IX500.4
INSTALLATION
Mounting: Choose a structurally sound location to mount your KICKER amplifi er. Make sure there are no items
behind the area where the screws will be driven. Choose a location that allows at least 4” (10cm) of open
ventilation for the amplifi er. If possible, mount the amplifi er in the climate-controlled passenger compartment.
Drill four holes using a 7/64” (3mm) bit and use the supplied #8 screws to mount the amplifi er. Use the IXSM
mounting bracket (sold separately) to stack IX amplifi ers of different sizes.
PERFORMANCE
Authorized KICKER Dealer:
Purchase Date:
Serial Number:
Model: IX500.4
RMS Power
@ 14.4V, 4 stereo, 1% THD+NΩ
@ 14.4V, 2 stereo, 1% THD+NΩ
@ 14.4V, 4 mono, 1% THD+NΩ
75W x 4
125W x 4
250W x 2
Length 11-3/8” (288mm)
Height 2-3/16” (55mm)
Width 7-7/8” (200mm)
Frequency Response ± 1dB 20Hz–20kHz
Signal-to-noise Ratio 98dB, A-weighted, re: rated power
Input Sensitivity Low Level: 125mV–5V
High Level: 250mV–10V
Electronic Crossover Selectable HI/LO/OFF, Variable lo-pass 50–200Hz,
12dB/octave
Bass Boost Variable 0–18dB @ 40Hz
Maximum Effi ciency (2Ω) >80%
Pro Tip: To get the best performance from your new KICKER Amplifi er and extend the warranty by 1 year, use
genuine KICKER accessories and wiring.
IXSM
sold separately
3
Model External Fuse
(sold separately)
Power/Ground Wire KICKER Wiring Kit
IX500.4 2 x 50 Ampere 4 Gauge PK4, CK4, ZCK4
Wiring: Disconnect the vehicle’s battery to avoid an electrical short. Then, connect the ground wire to the
amplifi er. Make the ground wire short, 24” (60cm) or less, and connect it to a paint-and-corrosion-free, solid,
metal area of the vehicle’s chassis. Adding an additional ground wire of this same gauge (or larger) between the
battery’s negative post and the vehicle chassis is recommended.
The IX amplifi er has dual input sensitivity differential RCA inputs which will receive either high or low level signals
from your car stereo’s source unit. Ideally, when connecting the source unit to the amplifi er, the IX amplifi er’s input
level switch should be set to “LO” and a low-level signal should run from the source unit’s stereo RCA output to
the stereo RCA input on the end panel of the amplifi er using RCA interconnect cable. If a low-level stereo RCA
output is not available on the source unit, the signal can be delivered to the amplifi er using the high-level speaker
outputs on the source unit. Set the input level switch on the end panel of the amplifi er to “HI”. Crimp and solder
RCA connectors to the end of the speaker wire running from the high-level speaker outputs on the source unit
and connect the wire to the RCA Inputs on the end panel of the amplifi er or simplify the installation by using a
KICKER ZISL as shown below. Either input method will provide a low-level output signal at the RCA output, which
effectively passes the audio signal to another amplifi er or component. Keep the audio signal cable away from
factory wiring harnesses and other power wiring. If you need to cross this wiring, cross it at a 90 degree angle.
source unit
high-level speaker
outputs
to amplifi er
shield
+
–
core conductor
Install a fuse within 18” (45cm) of the battery and in-line with the power cable connected to your amplifi er. Install
a second fuse within 18” (45cm) of the amplifi er. If you ever need to remove the amplifi er from the vehicle after it
has been installed, the ground wire should be the last wire disconnected from the amplifi er--just the opposite as
when you installed it.
KICKER ZISL
source unit high-level
speaker outputs
OR to amplifi er
INPUT
LEVEL
LO
HI
AMP2AMP1
L
R
OUTPUT
POWERAMP1
GNDL+ L– R+ R– REM +12V
AUTO
TURN ON
12V DC AUDIO
OFFSET
FADER
OFF
ON
BRIDGED
AMP2
L+ L– R+ R–
BRIDGED
12V
18”
(45cm)
battery
external fuse
external fuse
remote turn-on
(see page 5)
bare-metal
chassis ground
24”
(60cm)

Produktspecifikationer

Varumärke: Kicker
Kategori: bilradio
Modell: IX500.4

Behöver du hjälp?

Om du behöver hjälp med Kicker IX500.4 ställ en fråga nedan och andra användare kommer att svara dig


bilradio Kicker Manualer

Kicker

Kicker KX300.4 Bruksanvisning

4 Oktober 2024
Kicker

Kicker IX 1302 Bruksanvisning

1 Oktober 2024
Kicker

Kicker KX100.2 Bruksanvisning

29 September 2024
Kicker

Kicker IX 406 Impulse Bruksanvisning

23 September 2024
Kicker

Kicker KX850.4 Bruksanvisning

18 September 2024
Kicker

Kicker DX 700 Class D Bruksanvisning

16 September 2024
Kicker

Kicker ZX 300.1 Bruksanvisning

10 September 2024
Kicker

Kicker KX 550.2 Bruksanvisning

9 September 2024
Kicker

Kicker kx 550 3 Bruksanvisning

6 September 2024
Kicker

Kicker sx 700 4 Bruksanvisning

3 September 2024

bilradio Manualer

Nyaste bilradio Manualer

Ground Zero

Ground Zero GZTA 5125X Bruksanvisning

27 Oktober 2024
Ground Zero

Ground Zero GZHA 2250 X Bruksanvisning

27 Oktober 2024
Fusion

Fusion PP-AM16004 Bruksanvisning

27 Oktober 2024
Ultimate

Ultimate t3 4320 Bruksanvisning

27 Oktober 2024
Grundig

Grundig CHALLENGE 530 DAB Bruksanvisning

23 Oktober 2024
Audison

Audison srx 3 Bruksanvisning

20 Oktober 2024
Kenwood

Kenwood KMM-204 Bruksanvisning

20 Oktober 2024
Audison

Audison lr 180 m Bruksanvisning

20 Oktober 2024
Audison

Audison lr 435 xr Bruksanvisning

20 Oktober 2024
Daewoo

Daewoo AKL 3010 Bruksanvisning

20 Oktober 2024