Kicker KX2400.1 Bruksanvisning

Kicker bilradio KX2400.1

Läs nedan 📖 manual på svenska för Kicker KX2400.1 (28 sidor) i kategorin bilradio. Denna guide var användbar för 13 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF

Sida 1/28

Owner’s Manual |

Manual del Propietario |

Benutzerhandbuch |

Manuel d’utilisation |

KX Amplifiers

2013 KX Mono Amps Rev G.indd 1

2013 KX Mono Amps Rev G.indd 12013 KX Mono Amps Rev G.indd 1 11/13/2012 2:13:57 PM

11/13/2012 2:13:57 PM

11/13/2012 2:13:57 PM11/13/2012 2:13:57 PM

KX.1-SERIES AMPLIFIERS

OWNER’S MANUAL

INSTALLATION

Mounting: Choose a structurally sound location to mount your KICKER ampliﬁ er. Make sure there are no items

behind the area where the screws will be driven. Choose a location that allows at least 4” (10cm) of open

ventilation for the ampliﬁ er. If possible, mount the ampliﬁ er in the climate-controlled passenger compartment. Drill

four holes using a 7/64” (3mm) bit and use the supplied #8 screws to mount the ampliﬁ er.

PERFORMANCE

Authorized KICKER Dealer:

Purchase Date:

Model Number:

Serial Number:

Model: KX400.1 KX800.1 KX1200.1 KX1600.1 KX2400.1

RMS Power

@ 14.4V, 4 1% THD+NΩ mono, 

@ 14.4V, 2 mono, 1% THD+NΩ

200W x 1

400W x 1

800W x 1

600W x 1

1200W x 1

800W x 1

1600W x 1

1200W x 1

2400W x 1

Length | in [cm] 8 [20.4] 9 9/16 [24.4] 9 9/16 [24.4] 11 3/16 [28.4] 15 1/2 [39.4]

Speciﬁ cations common to all models:

Height | in [cm] 2 1/8 [5.5]

Width | in [cm] 8 5/16 [21]

Frequency Response ± 1dB 10Hz–160Hz

Signal-to-noise Ratio >95dB, A-weighted, re: rated power

Input Sensitivity Low Level: 125mV–5V

High Level: 250mV–10V

Electronic Crossover Variable Lo-pass 40Hz–160Hz, 24dB/octave

Bass Boost Parametric 20-80Hz; Variable Q: 1 to 5; Variable Boost, 0-18dB

Subsonic Filter Variable 10–80Hz, 24dB/octave

Remote Bass Yes [included]

Pro Tip: To get the best performance from your new KICKER Ampliﬁ er and extend the warranty by 1 year, use

genuine KICKER accessories and wiring.

MODEL: KX400.1 / KX800.1 / KX1200.1 / KX1600.1 / KX2400.1

2013 KX Mono Amps Rev G.indd 2

2013 KX Mono Amps Rev G.indd 22013 KX Mono Amps Rev G.indd 2 11/13/2012 2:17:11 PM

11/13/2012 2:17:11 PM

11/13/2012 2:17:11 PM11/13/2012 2:17:11 PM

Wiring: Disconnect the vehicle’s battery to avoid an electrical short. Then, connect the ground wire to the

ampliﬁ er. Make the ground wire short, 24” (60cm) or less, and connect it to a paint-and-corrosion-free, solid,

metal area of the vehicle’s chassis. Adding an additional ground wire of this same gauge (or larger) between the

battery’s negative post and the vehicle chassis is recommended.

The KX ampliﬁ er has dual input sensitivity differential RCA inputs which will receive either high or low level signals

from your car stereo’s source unit. A high-level signal can be run from the source unit’s speaker outputs to the

stereo RCA input on the end panel of the ampliﬁ er using the KICKER ZISL as shown (make sure you set the KX

ampliﬁ er’s input level switch to “HI”). Alternatively, the signal can be delivered to the ampliﬁ er using the low-level

RCA outputs on the source unit. Set the input level switch on the end panel of the ampliﬁ er to “LO”. Either input

method will provide a low-level output signal at the RCA output, which effectively passes the audio signal to

another ampliﬁ er or component. Keep the audio signal cable away from factory wiring harnesses and other

power wiring. If you need to cross this wiring, cross it at a 90 degree angle.

source unit

high-level speaker

outputs

to ampliﬁ er

shield

––

–

core conductor KICKER ZISL (optional)

source unit high-level

speaker outputs

OR to ampliﬁ er

Model External Fuse

(sold separately)

Power/Ground Wire KICKER Wiring Kit

KX400.1 1 x 60 Ampere 4 Gauge PK4, CK44, ZCK44

KX800.1 1 x 100 Ampere 4 Gauge PK4, CK44, ZCK44

KX1200.1 1 x 150 Ampere 1/0 Gauge PKD1, PWB050

KX1600.1 1 x 150 Ampere 1/0 Gauge PKD1, PWB050

KX2400.1 1 x 200 Ampere 1/0 Gauge PKD1, PWB050

Install a fuse within 18” (45cm) of the battery and in-line with the power cable connected to your ampliﬁ er. If you

ever need to remove the ampliﬁ er from the vehicle after it has been installed, the ground wire should be the last

wire disconnected from the ampliﬁ er--just the opposite as when you installed it.

2013 KX Mono Amps Rev G.indd 3

2013 KX Mono Amps Rev G.indd 32013 KX Mono Amps Rev G.indd 3 11/13/2012 2:17:12 PM

11/13/2012 2:17:12 PM

11/13/2012 2:17:12 PM11/13/2012 2:17:12 PM

Produktspecifikationer

Varumärke:	Kicker
Kategori:	bilradio
Modell:	KX2400.1
Färg på produkten:	Wit
Antal program:	6
Snäll:	Automatische naaimachine
Tillgångar:	72 W
Typ av mat:	Electrisch
Omvänd:	Ja
Inbyggt ljus:	Ja
AC-ingångsspänning:	110 V
Symaskinens funktioner:	Naaiwerk
Fri arm:	Ja
Typ av knapphål:	4 Step
Antal stygnmönster:	6