Kicker KX800.1 Bruksanvisning

Kicker bilradio KX800.1

Läs nedan 📖 manual på svenska för Kicker KX800.1 (28 sidor) i kategorin bilradio. Denna guide var användbar för 9 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Sida 1/28
Owner’s Manual |
Manual del Propietario |
Benutzerhandbuch |
Manuel d’utilisation |
KX Amplifiers
2013 KX Mono Amps Rev G.indd 1
2013 KX Mono Amps Rev G.indd 1
2013 KX Mono Amps Rev G.indd 1
2013 KX Mono Amps Rev G.indd 12013 KX Mono Amps Rev G.indd 1 11/13/2012 2:13:57 PM
11/13/2012 2:13:57 PM
11/13/2012 2:13:57 PM
11/13/2012 2:13:57 PM11/13/2012 2:13:57 PM
2
KX.1-SERIES AMPLIFIERS
OWNER’S MANUAL
INSTALLATION
Mounting: Choose a structurally sound location to mount your KICKER amplifi er. Make sure there are no items
behind the area where the screws will be driven. Choose a location that allows at least 4” (10cm) of open
ventilation for the amplifi er. If possible, mount the ampli er in the climate-controlled passenger compartment. Drill
four holes using a 7/64” (3mm) bit and use the supplied #8 screws to mount the amplifi er.
PERFORMANCE
Authorized KICKER Dealer:
Purchase Date:
Model Number:
Serial Number:
Model: KX400.1 KX800.1 KX1200.1 KX1600.1 KX2400.1
RMS Power
@ 14.4V, 4 1% THD+NΩ mono,
@ 14.4V, 2 mono, 1% THD+NΩ
200W x 1
400W x 1
400W x 1
800W x 1
600W x 1
1200W x 1
800W x 1
1600W x 1
1200W x 1
2400W x 1
Length | in [cm] 8 [20.4] 9 9/16 [24.4] 9 9/16 [24.4] 11 3/16 [28.4] 15 1/2 [39.4]
Specifi cations common to all models:
Height | in [cm] 2 1/8 [5.5]
Width | in [cm] 8 5/16 [21]
Frequency Response ± 1dB 10Hz–160Hz
Signal-to-noise Ratio >95dB, A-weighted, re: rated power
Input Sensitivity Low Level: 125mV–5V
High Level: 250mV–10V
Electronic Crossover Variable Lo-pass 40Hz–160Hz, 24dB/octave
Bass Boost Parametric 20-80Hz; Variable Q: 1 to 5; Variable Boost, 0-18dB
Subsonic Filter Variable 10–80Hz, 24dB/octave
Remote Bass Yes [included]
Pro Tip: To get the best performance from your new KICKER Amplifi er and extend the warranty by 1 year, use
genuine KICKER accessories and wiring.
MODEL: KX400.1 / KX800.1 / KX1200.1 / KX1600.1 / KX2400.1
2013 KX Mono Amps Rev G.indd 2
2013 KX Mono Amps Rev G.indd 2
2013 KX Mono Amps Rev G.indd 2
2013 KX Mono Amps Rev G.indd 22013 KX Mono Amps Rev G.indd 2 11/13/2012 2:17:11 PM
11/13/2012 2:17:11 PM
11/13/2012 2:17:11 PM
11/13/2012 2:17:11 PM11/13/2012 2:17:11 PM
3
Wiring: Disconnect the vehicle’s battery to avoid an electrical short. Then, connect the ground wire to the
amplifi er. Make the ground wire short, 24” (60cm) or less, and connect it to a paint-and-corrosion-free, solid,
metal area of the vehicle’s chassis. Adding an additional ground wire of this same gauge (or larger) between the
batterys negative post and the vehicle chassis is recommended.
The KX amplifi er has dual input sensitivity differential RCA inputs which will receive either high or low level signals
from your car stereos source unit. A high-level signal can be run from the source unit’s speaker outputs to the
stereo RCA input on the end panel of the amplifi er using the KICKER ZISL as shown (make sure you set the KX
amplifi ers input level switch to “HI”). Alternatively, the signal can be delivered to the amplifi er using the low-level
RCA outputs on the source unit. Set the input level switch on the end panel of the ampli er to “LO”. Either input
method will provide a low-level output signal at the RCA output, which effectively passes the audio signal to
another ampli er or component. Keep the audio signal cable away from factory wiring harnesses and other
power wiring. If you need to cross this wiring, cross it at a 90 degree angle.
source unit
high-level speaker
outputs
to amplifi er
shield
+
+
+
core conductor KICKER ZISL (optional)
source unit high-level
speaker outputs
OR to amplifi er
Model External Fuse
(sold separately)
Power/Ground Wire KICKER Wiring Kit
KX400.1 1 x 60 Ampere 4 Gauge PK4, CK44, ZCK44
KX800.1 1 x 100 Ampere 4 Gauge PK4, CK44, ZCK44
KX1200.1 1 x 150 Ampere 1/0 Gauge PKD1, PWB050
KX1600.1 1 x 150 Ampere 1/0 Gauge PKD1, PWB050
KX2400.1 1 x 200 Ampere 1/0 Gauge PKD1, PWB050
Install a fuse within 18” (45cm) of the battery and in-line with the power cable connected to your amplifi er. If you
ever need to remove the amplifi er from the vehicle after it has been installed, the ground wire should be the last
wire disconnected from the amplifi er--just the opposite as when you installed it.
2013 KX Mono Amps Rev G.indd 3
2013 KX Mono Amps Rev G.indd 3
2013 KX Mono Amps Rev G.indd 3
2013 KX Mono Amps Rev G.indd 32013 KX Mono Amps Rev G.indd 3 11/13/2012 2:17:12 PM
11/13/2012 2:17:12 PM
11/13/2012 2:17:12 PM
11/13/2012 2:17:12 PM11/13/2012 2:17:12 PM

Produktspecifikationer

Varumärke: Kicker
Kategori: bilradio
Modell: KX800.1

Behöver du hjälp?

Om du behöver hjälp med Kicker KX800.1 ställ en fråga nedan och andra användare kommer att svara dig




bilradio Kicker Manualer

bilradio Manualer

Nyaste bilradio Manualer