Kicker KX800.2 Bruksanvisning

Kicker bilradio KX800.2

Läs nedan 📖 manual på svenska för Kicker KX800.2 (12 sidor) i kategorin bilradio. Denna guide var användbar för 7 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF

Sida 1/12

Congratulations! You have just purchased the latest in amplifier tech-

nology to carry the famous KICKER name. Your KICKER KX series

amplifier is designed and built to give you years of powerful and trou-

ble-free performance. This installation manual contains valuable infor-

mation on how to get the most out of your new KX series amplifier.

Thanks for buying KICKER. Enjoy!

KX Amplifier Features

NEW for 2002 Radically advanced chassis with removable chassis shroud.

Low Impedance Operation Stable into 2 ohm stereo or 4 ohm mono

loads.

SORT Protection Circuitry ( ver-voltage, Short circuit, O Reverse polarity,

Thermal) Protects amplifier from accidents and undesired operation.

MOSFET Power Supply Provides high efficiency operation.

KickBass Variable bass boost circuit which provides up to 18 dB of boost at 40

Hz.

Built-In Variable Crossover 12 dB High pass or Low pass variable from 50-

200 Hz. Defeatable for full range operation.

High & Low level inputs Allows connection to various sources such as:

aftermarket stereos, factory radios, DVD players, Video Cassette Player, etc.

PAST P A S T(re mp ignal ransfer) Output RCA jacks to pass the incoming signal to

another amplifier or component.

Custom tooled gold plated connectors Assure maximum power transfer

and damping.

SAMS S A M S( tereo nd ono imultaneously) Amplifier will operate into a bridged

mono load and a stereo load at the same time.

Remote Bass Level Control Dash mounted for maximum control.

Three Year Warranty When

purchased from and installed by

Authorized

KICKER dealer.

KX300.2 / KX400.2 / KX500.2 /

KX800.2

Mounting Instructions

When selecting a location to mount your Kicker amplifier be sure it is struc-

turally sound and that there are no items behind the area that could be dam-

aged by the screws. Check for wiring, brake lines, fuel lines, gas tanks, etc.

All amplifiers generate heat under normal operation. Be sure to choose a loca-

tion that allows adequate ventilation for the amplifier. Also consider that the air

temperature inside an automobile’s trunk can reach upwards of 140 degrees

fahrenheit. An amplifier mounted here may require additional cooling needs

such as fans or venting to allow cool operation. If possible, mounting the amp in

the passenger compartment will allow cooler operation.

Remember that the controls on top of the amp will need to be accessible for

adjustment later. Keep this in mind as you choose your amplifier’s mounting

location.

Now that you are ready to mount your amplifier, use the supplied 3mm allen

wrench to remove the amplifier shroud. This will give you access to the mount-

ing holes in the amplifier and all wiring connections.

Remove Remove

With the shroud removed, you now have access to the four mounting holes in

the mounting feet and all wiring connections. Drill 4 holes using a 7/64” drill bit

and use the supplied #8 screws to mount the amplifier.

Wiring Instructions

Signal can be input into the amplifier using either the low level RCA input con-

nections or the high level speaker level connections. Using the low level RCA

connections is the preferred method. Use the high level inputs only if your head

unit does not have low level RCA type outputs. Connecting to the amp with

either input will provide a low level signal at the output (PAST) jacks.

The use of twisted pair interconnects is recommended for all installations to

minimize noise. When routing these cables through the automobile, try to keep

them away from factory wiring harnesses and other power wiring. If you need to

cross any of this wiring do so at a 90 degree angle to reduce the possibility for

noise problems.

When working with power connections it is always recommended that you dis-

connect the battery to prevent accidents.

The ground should be connected to the amplifier first before making any of

the other connections. This wire should be as short as possible (24 inches or less)

and connected to a paint/corrosion free solid metal area of the car’s chassis. Use

the same gauge wire as recommended for the amplifiers power connection to

the battery. Adding an additional ground wire between the car battery’s negative

post and the car chassis of this same gauge (or larger) is also recommended.

If you ever need to remove the amp from the vehicle after it has been

installed, the ground wire should be the last wire disconnected from the amplifi-

er, just the opposite as when you installed it.

A fuse must be installed within 18 inches of the battery to protect the power

wire feeding your amplifier. This fuse should be of at least the same value used

in the amplifier but no higher than the capacity of the wire. See the chart below

for wire size and fusing recommendations.

Model Fuse Size Wire Size

KX300.2 50A 8 GA

KX400.2 60A 4 GA

KX500.2 70A 4 GA

KX800.2 120A 2 GA

SOURCE UNIT

Left +

Left -

Right -

Right +

Speaker

Outputs

RCA

Outputs

WARNING-Use Only One...Never Both At The Same Time !!!

Produktspecifikationer

Varumärke:	Kicker
Kategori:	bilradio
Modell:	KX800.2
Vikt:	1240 g
Bredd:	68 mm
Djup:	244.2 mm
Höjd:	38.8 mm
Internationell säkerhetskod (IP):	IP20
Hållbarhetscertifikat:	RoHS
Uteffekt:	240 W
Spännande:	54 V
AC-ingångsspänning:	90 - 305 V