Kicker KX800.4 Bruksanvisning

Kicker bilradio KX800.4

Läs nedan 📖 manual på svenska för Kicker KX800.4 (12 sidor) i kategorin bilradio. Denna guide var användbar för 8 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF

Sida 1/12

Congratulations! You have just purchased the latest in amplifier tech-

nology to carry the famous KICKER name. Your KICKER KX series

amplifier is designed and built to give you years of powerful and trou-

ble-free performance. This installation manual contains valuable infor-

mation on how to get the most out of your new KX series amplifier.

Thanks for buying KICKER. Enjoy!

KX Amplifier Features

Low Impedance Operation Stable into 2 ohm stereo or 4 ohm mono loads.

SORT Protection Circuitry ( ver-voltage, Short circuit, O Reverse polarity,

Thermal) Protects amplifier from accidents and undesired operation.

MOSFET Power Supply Provides high efficiency operation.

KickBass Variable bass boost circuit which provides up to 18 dB of boost at 40

Hz.

Built-In Variable Crossover 12 dB High pass or Low pass variable from 50-

200 Hz. Defeatable for full range operation.

High & Low level inputs Allows connection to various sources such as: after-

market stereo, factory radio, DVD Player, Video Cassette Player, etc..

Custom tooled gold plated connectors Assure maximum power transfer

and damping.

SAMS S A M S( tereo nd ono imultaneously) Amplifier will operate into a bridged

mono load and a stereo load at the same time.

Remote Bass Level Control Dash mounted for maximum control.

(Not included in the KX300.4)

Two Year Warranty When

purchased from and installed by

an Authorized

KICKER Dealer.

KX300.4 / KX600.4 / KX800.4

With the shroud removed, you now have access to the four mounting holes in

the mounting feet and all wiring connections. Drill 4 holes using a 7/64” drill bit

and use the supplied #8 screws to mount the amplifier.

REMOVE REMOVE

REMOVE

Mounting Instructions

When selecting a location to mount your Kicker amplifier be sure it is struc-

turally sound and that there are no items behind the area that could be dam-

aged by the screws. Check for brake lines, fuel lines, gas tanks, or wiring harness-

es etc.

All amplifiers generate heat under normal operation. Be sure to choose a loca-

tion that allows adequate ventilation for the amplifier. Also consider that the air

temperature inside an automobiles trunk can reach upwards of 140 degrees

fahrenheit. An amplifier mounted here may require additional cooling tactics

such as fans or venting to allow cool operation. If possible, mounting the amp in

the passenger compartment will allow cooler operation.

Remember that the controls on top of the amp will need to be accessible for

adjustment later. Keep this in mind as you choose your amplifier’s mounting

location.

Now that you are ready to mount your amplifier, use the supplied 3mm allen

wrench to remove the amplifier shroud. This will give you access to the mount-

ing holes in the amplifier and all wiring connections.

Wiring Instructions

Signal can be input into the amplifier using either the low level RCA input con-

nections or the high level (speaker level) connections. Using the low level RCA

connections is the preferred method. Use the high level inputs only if your head

unit does not have low level RCA type outputs.

The use of twisted pair interconnects is recommended for all installations to

minimize noise. When routing these cables through the automobile, try to keep

them away from factory wiring harnesses and other power wiring. If you need to

cross any of this wiring do so at a 90 degree angle to reduce the potential of

noise problems.

When working with power connections it is always recommended that you dis-

connect the battery to prevent accidents.

The ground should be connected to the amplifier first before making any of

the other connections. This wire should be as short as possible (24 inches or less)

and connected to a paint/corrosion free solid metal area of the car’s chassis. Use

the same gauge wire as recommended for the amplifiers power connection to

the battery. Adding an additional ground wire between the car battery’s negative

post and the car chassis of this same gauge (or larger) is also recommended.

If you ever need to remove the amp from the vehicle after it has been

installed, the ground wire should be the last wire disconnected from the amplifi-

er, just the opposite as when you installed it.

A fuse must be installed within 18 inches of the battery to protect the power

wire feeding your amplifier. This fuse should be of at least the same value used

in the amplifier but no higher than the capacity of the wire. See the chart below

for wire size and fusing recommendations.

Model Fuse Size Wire Size

KX-300.4 40A 8 GA

KX-600.4 80A 4 GA

KX-800.4 120A 2 GA

L R L R

Amp 1 Amp 2

L+ L - R + R - L+ L - R + R -

SOURCE UNIT

BRIDGE BRIDGE

LEFT +

LEFT -

RIGHT -

RIGHT +

LEFT +

LEFT -

RIGHT -

RIGHT +

Amp 2

A MP 1

Amp 1 Amp 2

+ - - + + - - + WARNING-Use Only

High Or Low Level

NOT...Both!!!

OFF

PAS S

LO PASS

OFF

HI PASS

LO PASS

AMP 1 AMP 2

HI-LEVEL INPUT

MP 1

AMP 2

REMOT E B ASS

Produktspecifikationer

Varumärke:	Kicker
Kategori:	bilradio
Modell:	KX800.4
Färg på produkten:	Aqua-kleur
Sladdlängd:	5 m
Hållbarhetscertifikat:	RoHS
Antal per paket:	1 stuk(s)
Innehåller inte:	Halogeen
Förvaringstemperatur:	-40 - 70 °C
Full duplex:	Ja
Drifttemperatur (TT):	0 - 60 °C
Anslutning 1:	PanMPO
Anslutning 2:	12x LC
Anslutning 1 typ:	Mannelijk
Anslutning 2 typ:	Mannelijk
Kabelns diameter:	3 mm
Yttre mantelmaterial:	Halogeenvrij
Kern diameter:	50 µm
Klädselns diameter:	125 µm
Fiberoptisk typ:	OM3