Kicker ZX550.3 Bruksanvisning
Läs nedan 📖 manual på svenska för Kicker ZX550.3 (10 sidor) i kategorin bilradio. Denna guide var användbar för 12 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare
Sida 1/10
ZX
MULTI-CHANNELAMPLIFIER
with a CLASS-DSUBWOOFERCHANNEL
ZX ZX550 ,.3 700.5
©2006 Stillwater Designs
English Version
Versión spañolE
A S 5mplificador del la erie ZX.3/ZX.
Manual del Propietario
Deutsche Version
S 5 Stereoverstärker der ZX.3/ZX. - erie
Benutzerhandbuch
Version rançaiseF
A 5mplificateur de série ZX.3/ZX.
Manuel d'utilisation
Installation . . . as easy as 1, , 2 3
1. Mounting Choose a structurally sound location to mount your Kicker amplifier. The controls on the
top of the amplifier need to be accessible for adjustment. Make sure there are no items behind the area
where the screws will be driven. Choose a location that allows at least 4” (10cm) of open ventilation for
the amplifier. If possible, mount the amplifier in the climate-controlled passenger compartment. Drill four
holes using a 7/64” (3mm) bit and use the supplied #8 screws to mount the amplifier.
2. Wiring Disconnect the vehicle’s battery to avoid an electrical short. Then connect the ground wire
to the amplifier. Make the ground wire short, 24” (60cm) or less, and connect it to a paint-and
corrosion-free solid-metal area of the vehicle's
chassis. Adding an additional ground wire between
the battery's negative post and the vehicle chassis
of this same gauge (or larger) is recommended.
Use a twisted pair(s) of RCA (low-level)
interconnect cable to feed the audio signal to the
amplifier. If you are using only one pair of RCA
inputs, connect the RCA cable to the AMP 1
inputs. All three (or five ZX700.5) channels will
work with a single pair of RCA input cable; the
fader will not operate. Keep the RCA cable away
from factory wiring harnesses and other power
wiring. If you need to cross this wiring, cross it at a
90 degree angle.
Only use speaker wire (high-level) inputs if your source unit does not have RCA type outputs. When
using both sets of high-level inputs for the ZX700.5, the supplied RCA dummy plugs must be inserted
into the RCA AMP 2 inputs in order for the fader to work properly. In any other configuration do not use
the RCA dummy plugs. Never use shorting plugs in any configuration. See Figure 1.
Install a fuse within 18” (45cm) of the battery and in-line with the power cable connected to your
amplifier. If you ever need to remove the amplifier from the vehicle after it has been installed, the ground
wire should be the last wire disconnected from the amplifier--just the opposite as when you installed it.
See the chart below for power and
ground wire size, and fusing
recommendations.
3. Configuration The following diagrams show the most common configurations for your Kicker ZX
series amplifier.
F 5our (ZX700. ) / Two ubwoofer Channel (ZX peration with 550.3) O S These ZX amplifiers are
capable of operating into a minimum impedance of 2 ohms per channel in stereo operation and
2 ohms mono in the subwoofer channel. See Figure 3.
B O 5ridged (Mono) peration (ZX700. ) The ZX700.5 series amplifier is capable of operating into a
minimum impedance of 4 ohms when in bridged operation. This allows you to bridge AMP 1 to run the
“right” side and AMP 2 to run the “left” side. You will need two RCA Y-Adapters for this configuration.
Each AMP is stable down to 4 ohms in this configuration. See Figure 4.
I TNS ALLA ONTI
ZX ZX.3/ .5AMPLIFIER
ZX ZX550.3 /700.5
Multi-ChannelModels:
ZX.3 ZX.5/SeriesAmplifier
Owner’sManual
Congratulations on your
KICKER purchase
Please record your purchase
information and keep your sales
receipt for validation of warranty.
Authorized Kicker Dealer:
Purchase Date:
Amplifier Model Number:
Amplifier Serial Number:
__________________________
__________________________
__________________________
__________________________
SUB INPUT
SUB
SOURCE UNIT
killers trk7“on Top”
Model FuseZX550.3 60APowerG d 4rounWire GA
Model FuseZX700.5 90APowerG d 4rounWire GA
Remote
Turn-On
Battery
+12V Fuse
18"
Or Less
(45cm)
24"
Or Less
(60cm)
G droun
-+
+- + -
Signal In AMP 1
Signal In AMP 2
Left Speaker AMP 1 Right Speaker AMP 1
Minim ance f 2 hms in the S bw fer Channelum imped o o u oo
an 2 perati n f the AMPsd ohms per channel in stereo o o o
Signal In Subw feroo
(Opti nal)o
+- +
Left Speaker AMP 2 Right Speaker AMP 2
-
M no o Speaker
Subwoofer Channel
Rem teo
Turn-On
Battery
+12V Fuse
18"
Or Less
(45cm)
24"
Or Less
(60cm)
G droun
-+
+- + -
Signal In AMP 1 (Right)
Signal In AMP 2 (Left)
M no o Speaker
Subwoofer Channel
Right Speaker AMP 1 Left Speaker AMP 2
Minim m impe ance f 2 bw fer Channelu d o ohms in the Su oo
an hms per AMP in bri ge peratid 4 o d d o on
Signal In S bw feru oo
(Opti nal)o
23
Figure 3
Figure 4
Use ne type signal only o of inp theu t to
amplifier either RCA Cable Speaker, or Wire
RCA Cable
(L el)ow-Lev
Speaker Wire
(High-Level
Output)
Speaker Wire
(High-Level Input)
Left +
Left -
Right -
Right +
CONF URAIG TION
W o vhen using b th sets of high-le el
(speaker RCA wire) inp ts the pplie u usd
du d o mmy plugs um st be inserte int the
RCA AMP er 2 inp ts inu ord of r
the fa rk perly der oto w pro .
Left +
Left -
Right -
Right +
Opti nal RCAo
S tubwoofer Cable Inpu
Opti nal RCAo
S O tubwoofer Cable utpu
Figure 1
ZX7 .500
SUB INPUT
SUB
SOURCE UNIT
killers trk7“on Top”
Use ne type signal only o of inp theu t to
amplifier either RCA Cable Speaker, or Wire
RCA Cable
(L el)ow-Lev
Speaker Wire
(High-Level
Output)
Speaker Wire
(High-Level Input)
Left +
Left -
Right -
Right +
Opti nal RCAo
Subwoofer Cable
Figure 2
ZX55 .30
ZX7 .500
ZX7 .500
Note: To get the best performance from your new Kicker Amplifier, we recommend using genuine Kicker Accessories and Wiring.
Note: All specifications and performance figures are subject to change. Please visit the www.kicker.com for the most current information.
Operation
Your Kicker ZX series amplifier has five (or seven ZX700.5) rotary controls on top and one
(or two ZX700.5) switch(es) on the end-panel. Before turning on the system for the first time, turn the
rotary controls on the top of the amplifier to the full counter-clockwise position.
1. CrossoverSwitch The crossover switch(es) on the end-panel is
(are) for setting the internal crossover(s) for the “full-range” audio
channels (12dB slope per octave). In the OFF position the amplifier
passes a full-range signal to the speakers. The HI position should be
selected when connected to speakers, which you do not want to
receive any sub-bass information. Never change the crossover
"OFF/HI" switch setting with the audio system on!
2. InputGainControl The input gain control is not a volume control.
It matches the output of the source unit to the input level of the
amplifier. Turn the source unit up to about 3/4 volume (if the source
unit goes to 30, turn it to 25). Next, slowly turn (clockwise) the gain
on the amplifier up until you can hear audible distortion, then turn it
down a little. Set AMP 1 first, then AMP 2 (ZX700.5 only) and finally
the Subwoofer Channel input gain control.
3. BassBoostControl The bass boost control is designed to give
you increased output 0 - 18dB at 40Hz for the subwoofer channel.
The setting for this control is subjective. If you turn it up, you must go
back and adjust the input gain control to avoid clipping the amplifier.
4. CrossoverControl The setting for this control is subjective; 80Hz is a good place to start.
5 B. Remote ass(Level Control) When using the remote bass level control you have the ability to
control the level of the Subwoofer Channel’s output remotely. To mount the remote bass level control,
simply screw the metal bracket to the
chosen location. Then slide the
housing onto the bracket until it
snaps into place. Run the cable from
the controller to the “Remote Bass”
jack on the amplifier chassis.
TroubleShooting
If your amplifier does not appear to be
working, check the obvious things first
such as blown fuses, poor or incorrect
wiring connections, incorrect setting of
crossover switch and gain controls, etc.
There are two LEDs on the top of your
Kicker ZX series amplifier, one green and
one red. When the green LED is lit this indicates the amplifier is turned on and no trouble exists. If the green LED turns
off and the red LED is lit, this indicates that the protection circuitry (SORT) is engaged.
Green LED off, no output? With a Volt Ohm Meter (VOM) check the following: 1) +12 volt power terminal
(should read +12V to +16V) 2) Remote turn-on terminal (should read +12V to +16V) 3) Check for reversed power
and ground connections 4) Ground terminal, for proper conductivity
Green LED on, no output? Check the following: 1) RCA connections 2) Test speaker outputs with a “known”
good speaker. 3) Substitute source unit with a “known” good source unit. 4) Check for a signal in the RCA cable
feeding the amplifier with the “AC” test position selected on the VOM meter.
R ,ed LED on no output? 1) Amplifier is very hot. Thermal protection is engaged. Test for proper impedance at
the speaker terminals with a VOM meter (see the diagrams in this manual for minimum recommended impedance and
multiple speaker wiring suggestions). Also check for adequate airflow around the amplifier. 2) Amplifier shuts down
only while vehicle is running. Voltage protection circuitry is engaged. Voltage to the amplifier is not within the 9-16
volt operating range. Have the vehicle's charging and electrical system inspected. 3) Amplifier will only play at low
volume levels. Short circuit protection is engaged. Check for speaker wires shorted to each other or to the vehicle
chassis. Check for damaged speakers, or speaker(s) operating below the minimum recommended impedance.
No output from one channel? 1) Check the balance control on source unit 2) Check the RCA (or speaker input)
and speaker output connections for the channel 3) Swap the RCA (or speaker input) cable from left to right. If the
problem changes sides then you have a bad RCA (or speaker input) cable or source unit problem. 4) Swap the
speaker output wire from left to right. If the problem changes sides then you have a bad speaker cable, passive
crossover network and/or speaker.
Alternator noise-whining sound with engine’s RPM? 1) Check for damaged RCA (or speaker input) cable
2) Check the routing of RCA (or speaker input) cable 3) Check the source unit for proper grounding 4) Check the
gain settings and turn them down if they are set too high
Poor stereo image or reduced bass response? Check system phasing by turning the balance control from left
to right. If there is more bass output when turned to either side, then check your speaker wiring, passive crossover
networks and speaker terminals for proper positive and negative connections. Reverse a speaker connection from
positive to negative on the stereo/subwoofer channel(s); if the bass improves, the speaker was out of phase.
Ground-L Noop oise? If you are using only one pair of RCA inputs, connect the RCA cable to the AMP 1 inputs.
N Fo ader? When using both sets of high-level inputs (ZX700.5 only), RCA dummy plugs must be inserted into
the RCA AMP 2 inputs in order for the fader to work properly. If you do not have dummy plugs available, use
unterminated RCA ends or cut the ends off of existing RCA cable. Do not use shorting plugs.
If you have more questions about the installation or operation of your new KICKER product, see the Authorized KICKER Dealer where you
made your purchase. For more advice on installation, click on the SUPPORT tab on the Kicker homepage, www.kicker.com. Choose the
TECHNICAL SUPPORT tab, choose the subject you are interested in, and then download or view the corresponding information. Please
E-mail support@kicker.com or call Technical Services (405) 624-8583 for unanswered or specific questions.
Please Note: Modern high performance speakers have a lower DC Resistance than what used to be available. The Kicker Coaxial and
Component speakers are rated at four ohms (some DC Resistances may be as low as 3 ohms) and work with any amplifier designed to
operate at a four ohm load. If you want to use two Kicker Coaxial or Component speakers on a single channel of your amplifier wire the
speakers in series. This will improve the sound quality, lower the total harmonic distortion and lessen the thermal load at the amplifier. This
may prevent an amplifier from shutting down, due to over-current protection circuitry.
CAUTION: When jump starting the vehicle, be sure that connections made with jumper cables are correct. Improper connections can
result in blown amplifier fuses as well as the failure of other critical systems in the vehicle.
Performance
Model ZX550.3 ZX700.5
RMS Power in Watts, AMP 1 and AMP 2 all channels driven
@14.4V, 4ΩStereo ≤1% THD+N 70 x 2 70 x 4
@14.4V, 2ΩStereo, ≤1% THD+N 85 x 2 85 x 4
@14.4V, 4ΩMono, ≤1% THD+N N/A 165 x 2
RMS Power in Watts, Subwoofer channel driven
@14.4V, 4ΩMono ≤1.5% THD+N 210 x 1 210 x 1
@14.4V, 2ΩMono, ≤1.5% THD+N 420 x 1 420 x 1
Length: 16 3/4” (425mm) 20” (507mm)
Specifications common to all models:
Height: 2 1/8” (54mm)
Width: 9 5/8” (244mm)
Frequency Response, ± 0.5 dB: 20 Hz - 20 kHz
Signal-to-Noise Ratio: >95 dB, a-weighted, re: rated power
Input Sensitivity: 125 mV - 5 V low level, 250 mV - 10 V high level
Electronic Crossover: Variable (defeatable) HI pass, 50 - 200Hz, 12bB per octave, for the full-range channels
Variable LOW pass, 50 - 200Hz, 24dB per octave, for the subwoofer channel
Bass Boost: Variable 0 to +18dB boost @ 40Hz, for the subwoofer channel
ZX ZX.3/ .5AMPLIFIER
4 5
Model .3ZX550
7 o d0 x 2, 210 x 1 @ 4 ohms fr m 20-20 20-200K, Hz, 14.4V c,
1 T D C (% H , EA-2006 Watts)
Signal ise Rati BA A-2006 A-weighte oto N o - 27 / -55 d EC (ref: 1W, d)
Model .5ZX700
7 o d0 x 4, x 210 1 @ 4 ohms fr m 20-20 20-200K, Hz, 14.4V c,
1% , T DHC (EA-2006 Watts)
Signal ise Rati BA A-2006 A-weighte oto N o - 27 / -55 d EC (ref: 1W, d)
P MERFOR ANCE
OPERATION
SUB INPUT SUB
Figure 6
Mount the metal bracket
Back View
Si Viewd e
4 C no ductor
Ph ne Cableo
Sli it int thed e the sing ntil hou u snaps o metal bracket
Figure 5
Cross er ntrov oCol
Subwoofer Channel
Bass st ntr Boo oCol
Subwoofer Channel
Subwoofer Channel
Inp ain ntrut G oCol
AMP 1 Input
G o oain C ntr l AMP 2 Input
G o oain C ntr l
Cross er ntrov oCol
AMP 2
Cross er ntrov oCol
AMP 1
ZX7 .500
Produktspecifikationer
| Varumärke: | Kicker |
| Kategori: | bilradio |
| Modell: | ZX550.3 |
Behöver du hjälp?
Om du behöver hjälp med Kicker ZX550.3 ställ en fråga nedan och andra användare kommer att svara dig
bilradio Kicker Manualer
4 Oktober 2024
1 Oktober 2024
29 September 2024
23 September 2024
18 September 2024
16 September 2024
10 September 2024
9 September 2024
6 September 2024
3 September 2024
bilradio Manualer
- bilradio Sony
- bilradio LG
- bilradio AEG
- bilradio Philips
- bilradio Panasonic
- bilradio Daewoo
- bilradio Ford
- bilradio Grundig
- bilradio JVC
- bilradio JBL
- bilradio Kenwood
- bilradio Medion
- bilradio Pioneer
- bilradio Volvo
- bilradio Aiwa
- bilradio Akai
- bilradio Alpine
- bilradio Audison
- bilradio Telefunken
- bilradio Silvercrest
- bilradio Lenco
- bilradio Pyle
- bilradio Manta
- bilradio Caliber
- bilradio Hyundai
- bilradio Renkforce
- bilradio Clatronic
- bilradio Sencor
- bilradio Overmax
- bilradio Blaupunkt
- bilradio Crunch
- bilradio Skoda
- bilradio Denver
- bilradio Stinger
- bilradio Sanyo
- bilradio Hifonics
- bilradio Brigmton
- bilradio Maginon
- bilradio Xomax
- bilradio Rockford Fosgate
- bilradio Marquant
- bilradio Krüger And Matz
- bilradio Audiosonic
- bilradio Clarion
- bilradio Muse
- bilradio Mac Audio
- bilradio Biltema
- bilradio Pure
- bilradio Audiovox
- bilradio Dual
- bilradio Boss
- bilradio Cobra
- bilradio MB Quart
- bilradio Auna
- bilradio Xblitz
- bilradio Tokai
- bilradio Nextbase
- bilradio Boston Acoustics
- bilradio Trevi
- bilradio Orion
- bilradio Magnat
- bilradio Adcom
- bilradio Autovision
- bilradio Lanzar
- bilradio Hertz
- bilradio Jensen
- bilradio Roadstar
- bilradio Scott
- bilradio Kunft
- bilradio Ultimate
- bilradio Conceptronic
- bilradio Fusion
- bilradio Revo
- bilradio Elta
- bilradio Axton
- bilradio VDO
- bilradio SPC
- bilradio Soundstream
- bilradio DLS
- bilradio VDO Dayton
- bilradio Macrom
- bilradio Becker
- bilradio Watssound
- bilradio Orava
- bilradio Scion
- bilradio RTO
- bilradio Cartronix
- bilradio Spectron
- bilradio Mtx Audio
- bilradio Ground Zero
- bilradio Multilaser
- bilradio ESX
- bilradio RetroSound
- bilradio Lark
- bilradio Planet Audio
- bilradio Rodek
- bilradio Eclipse
- bilradio Voxx
- bilradio SoundMAX
- bilradio Impulse
- bilradio Twister
- bilradio Majestic
- bilradio Mystery
Nyaste bilradio Manualer
27 Oktober 2024
27 Oktober 2024
27 Oktober 2024
27 Oktober 2024
23 Oktober 2024
20 Oktober 2024
20 Oktober 2024
20 Oktober 2024
20 Oktober 2024
20 Oktober 2024