Metra 70-5517 Bruksanvisning

Läs nedan 📖 manual på svenska för Metra 70-5517 (2 sidor) i kategorin Inte kategoriserad. Denna guide var användbar för 2 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Sida 1/2
120AFDI5V Converter (packaged separately)
Receiver Wiring Adaptor
120 70-5517
Revision 06/26/17
*120705517*
IMPORTANT
Before starting, compare items on your invoice with items
received. Thoroughly check packing materials. If an item
is missing, please call Crutchfield at 1-888-955-6000.
Red - 12 Volts Switched Power
Black - Chassis Ground
Gray - Right Front Speaker Positive
White - Left Front Speaker Positive
Green - Left Rear Speaker Positive
Violet - Right Rear Speaker Positive
Yellow - 12 Volts Constant Power
Gray/Black - Right Front Speaker Negative
White/Black - Left Front Speaker Negative
Green/Black - Left Rear Speaker Negative
Violet/Black - Right Rear Speaker Negative
Black/White - Amplifier Ground
Orange - Illumination
Copyright 2017 Crutchfield Corporation
STEP 1 -- CONNECT WIRES
A.
B.
C.
D.
E.
For best results, the RCA plug should be
connected to the subwoofer preamp output
on the new receiver.
Blue/Red - Connects to Blue/White
Wire on Amp/Sub harness
Black - Chassis Ground
Blue/White - Connects to Blue/White Amp Remote Wire from receiver
Match wires below to the matching function
of each wire on your receiver (refer to
instructions supplied with receiver).
The wire colors of your new receiver may, or
may not, match the wire colors of the
adaptor. Match adaptor and receiver wires
by function, disregarding color.
If your receiver does not have a Dimmer or
Illumination wire, tape off the Orange wire.
Connect the Black wire to Ground wire of
new receiver.
Connect all Black/White wires together and
secure to the chassis of the new receiver.
Individually tape off any unused wires.
Make final wiring connections following
instructions on the next page.
F.
Orange/Black - (not used - tape off)
Blue/White - Amplifier Turn-on Subwoofer Input
Receiver Wiring Adaptor Connections
120 70-5517
Page 2
STEP 2 -- CONTINUED
A. Strip wires back 1/2”.
B. Twist wires together and
insert in crimp cap.
C. Squeeze middle of cap
for tight connection.
Copyright 2017 Crutchfield Corporation
STEP 3 -- APPLICATION
When ready to install the receiver, plug
the Wiring Adaptor from the new receiver
or receiver assembly into the factory
radio harness(es) in the vehicle dash.
D. Complete crimp connections
for all necessary wires.
E. Be sure to wrap any wires from
the Wiring Adaptor that are
not necessary (wires with no
match from the new receiver)
with electrical tape.
STEP 2 -- CRIMP CONNECTIONS
Tools & Parts
Required
Wire Stripper/Crimp Tool Crimp Caps
Unused Wire (tape over bare wires)
Receiver Wiring Adaptor
Generic Illustration
Generic Illustration

Produktspecifikationer

Varumärke: Metra
Kategori: Inte kategoriserad
Modell: 70-5517

Behöver du hjälp?

Om du behöver hjälp med Metra 70-5517 ställ en fråga nedan och andra användare kommer att svara dig




Inte kategoriserad Metra Manualer

Metra

Metra 71-017C Bruksanvisning

26 September 2024
Metra

Metra AXSP-HK Bruksanvisning

26 September 2024
Metra

Metra 109-TO7 Bruksanvisning

26 September 2024
Metra

Metra 95-8273B Bruksanvisning

26 September 2024
Metra

Metra 95-7822 Bruksanvisning

26 September 2024
Metra

Metra 82-8703 Bruksanvisning

26 September 2024
Metra

Metra 82-9101 Bruksanvisning

26 September 2024
Metra

Metra 95-7021HG Bruksanvisning

26 September 2024
Metra

Metra 82-5608 Bruksanvisning

26 September 2024

Inte kategoriserad Manualer

Nyaste Inte kategoriserad Manualer