Metra 90-3037P Bruksanvisning

Metra Inte kategoriserad 90-3037P

Läs nedan 📖 manual på svenska för Metra 90-3037P (3 sidor) i kategorin Inte kategoriserad. Denna guide var användbar för 2 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF

Sida 1/3

IMPORTANT

Installation Kit

120 90-3037P

Before starting, compare items on your invoice with items

received. Carefully check through packaging material.

If an item is missing, please call:

Crutchfield

Parts Supplied:

Kit Frame

Support Tray

Chevrolet/GMC

Revision 05/03/04

Kit assembly instructions are on the following pages.

Page 1 of 3

*120903037P*

Mounting Brackets

(2) Studs (2) 3/8” Nuts

Trimplate

at 1-888-955-6000

FIGURE 2

Shaft Supports

Installation Kit

120 90-3037P

1. Press posts on trimplate into holes on to snap kit frame

parts together (Figure 1).

2. Use a utility knife to cut out in trimplate to shaft supports

create a DIN opening (Figure 2).

3. Push clips on into slots on rear of kit frame to support tray

secure (Figure 1).

4. Cut off tabs on both mounting brackets labeled “B” and “C”

that are shown as shaded (Figure 3). The tabs must “A”

remain.

5. Secure mounting brackets to sides of kit frame with studs

and nuts supplied (Figure 1).

6. Remove DIN sleeve from receiver and slide into opening in

trimplate. Secure sleeve to trimplate by bending the securing

tabs (Figure 4).

7. Slide receiver into sleeve/kit assembly.

DIN Receiver Assembly

Securing Tabs

DIN Sleeve

Bend tabs after sleeve

is inside assembly.

FIGURE 1

Trimplate

Kit Frame Support Tray

Left Mounting Bracket

Stud

Nut

Right Mounting Bracket

FIGURE 4

Tools Required

Utility

Knife

▲

Small Flat Blade

Screwdriver

1/4” & 3/8”

Sockets

Hacksaw

Chevrolet/GMC

FIGURE 3

Cut off

“B” & “C” tabs

(shaded)

“C”

“B”

“A” tabs remain

“A”

Installation Kit

120 90-3037P

Spacers

(supplied with

your order)

1. Press posts on trimplate into holes on to snap partskit frame

together (Figure 1).

2. Push clips on into slots on rear of kit frame support tray

to secure (Figure 1).

3. Cut off tabs on both mounting brackets labeled “B” and “C”

shown as shaded (Figure 2). The tabs must remain.“A”

4. Secure mounting brackets to sides of kit assembly with

studs nutsand supplied (Figure 1).

5. Choose the proper spacers (supplied with your order) to

allow receiver nosepiece to extend 1/8” to 1/4” beyond face of

trimplate (Figure 3).

6. Insert receiver shafts (with spacers in place) through openings

in trimplate. Secure receiver and faceplate with shaftnuts

supplied with receiver.

7. Attach control knobs.

1/8” -1/4”

▲

Spacer

Shaft Receiver Assembly

FIGURE 3

Shaftnuts

FIGURE 1

Trimplate

Kit Frame

Support Tray

Left Mounting Bracket

Faceplate

Control Knobs

Tools Required

▲

Deep Socket

(size depends upon receiver)

Stud

Nut

Right Mounting Bracket

1/4” & 3/8”

Sockets

FIGURE 2

Cut off

“B” & “C” tabs

(shaded)

Chevrolet/GMC

“C”

“B”

“A” tabs must remain

“A”

Hacksaw

Produktspecifikationer

Varumärke:	Metra
Kategori:	Inte kategoriserad
Modell:	90-3037P
Typ av operation:	Sensor
Färg på produkten:	Roestvrijstaal
Bredd:	595 mm
Djup:	548 mm
Höjd:	595 mm
Sladdlängd:	1.2 m
Barnlås:	Ja
Belysning inuti:	Ja
Total inomhuskapacitet (ugnar):	56 l
Antal automatiska program:	40
Mått för installationsfack (BxDxH):	560 x 550 x 575 mm
Tillgångar:	3650 W
Typ av ugn:	Elektrische oven
Ugnens termostatområde:	300 °C
Självrengörande:	Ja
Skriv timer:	Digitaal
Justerbar termostat:	Ja