Metra 95-7326 Bruksanvisning

Läs nedan 📖 manual på svenska för Metra 95-7326 (8 sidor) i kategorin Inte kategoriserad. Denna guide var användbar för 5 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Sida 1/8
METRA. The World’s best kits.metraonline.com © COPYRIGHT 2004-2015 METRA ELECTRONICS CORPORATION
REV. 10/15/2015 INST95-7326
Installation instructions for part 95-7326
CAUTION!
Metra recommends disconnecting the negative bat
-
tery terminal before beginning any installation, unless the vehicle
manufacturer recommends against so. Please check with your local
Dealership for more information. All accessories, switches, climate
controls panels, and especially air bag indicator lights must be con
-
nected before reconnecting the battery or cycling the ignition. Also,
do not remove the factory radio with the key in the on position, or the
vehicle running. It would be best to remove the key from the ignition
and then wait a few seconds before removing the factory radio.
• ISO DDIN radio provision
A) ISO DDIN trim plate B) ISO DDIN brackets
KIT FEATURES
KIT COMPONENTS
WIRING & ANTENNA CONNECTIONS (sold separately)
Wiring Harness: • 70-1004 • 70-7303
Antenna Adapter: • Not required
• Panel removal tool • Phillips screwdriver Cutting tool
TOOLS REQUIRED
(US Model Only) (Non Radio Delete) (Non Touring Model)
A B
Dash Disassembly ................................................. 2
Kit Assembly
ISO DDIN radio provision 3 ......................................
Table of Contents
95-7326
1. Unclip and remove the panel
surrounding the radio, including
the a/c vents and hazard button.
(Figure A)
2. Remove (4) Phillips screws to
remove radio. (Figure B)
Continue to kit assembly
Dash Disassembly
(Figure B)
1
2
3
4
A/C
(Figure A)
95-7326
Kit Assembly
CUT OUT BAR
CUT HERE
(Figure A) (Figure B) (Figure C)
ISO DDIN radio provision
1. Carefully cut, and remove the bar
in the factory radio trim panel.
(Figure A)
Note: The smoother the cut, the
better the 95-7326 will look in the
dash panel.
2. Snap the into ISO DDIN brackets
the inside edge of the ISO DDIN
trim plate. (Figure B)
3. Slide the radio into the assembly
from the rear. Secure the radio to
the assembly using the screws
supplied with the radio. (Figure C)
4.
Locate the factory wiring harness
and antenna plug in the dash and
make all necessary connections to
the radio. Metra recommends using
the proper mating adapters from
Metra and/or AXXESS. Re-connect
the negative battery terminal and
test the radio for proper operation.
5. Reassemble the dash in reverse
order of disassembly.

Produktspecifikationer

Varumärke: Metra
Kategori: Inte kategoriserad
Modell: 95-7326

Behöver du hjälp?

Om du behöver hjälp med Metra 95-7326 ställ en fråga nedan och andra användare kommer att svara dig




Inte kategoriserad Metra Manualer

Metra

Metra 71-017C Bruksanvisning

26 September 2024
Metra

Metra AXSP-HK Bruksanvisning

26 September 2024
Metra

Metra 109-TO7 Bruksanvisning

26 September 2024
Metra

Metra 95-8273B Bruksanvisning

26 September 2024
Metra

Metra 95-7822 Bruksanvisning

26 September 2024
Metra

Metra 82-8703 Bruksanvisning

26 September 2024
Metra

Metra 82-9101 Bruksanvisning

26 September 2024
Metra

Metra 95-7021HG Bruksanvisning

26 September 2024
Metra

Metra 82-5608 Bruksanvisning

26 September 2024

Inte kategoriserad Manualer

Nyaste Inte kategoriserad Manualer