Metra Axxess XSVI-1731-NAV Bruksanvisning

Metra Inte kategoriserad Axxess XSVI-1731-NAV

Läs nedan 📖 manual på svenska för Metra Axxess XSVI-1731-NAV (4 sidor) i kategorin Inte kategoriserad. Denna guide var användbar för 3 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF

Sida 1/4

Installation instructions for part XSVI-1731-NAV

REV. 9/29/2016 INSTXSVI-1731-NAV

Axxess Integrate

CAUTION!

All accessories, switches, climate controls panels, and

especially air bag indicator lights must be connected before cycling

the ignition. Also, do not remove the factory radio with the key in the

on position, or while the vehicle is running.

• Provides NAV outputs (parking brake, reverse, and speed sense)

• Pre-wired ASWC-1 harness included (ASWC-1 sold separately)

• Retains the factory backup camera

• Retains balance and fade

• Includes the AX-CAM6V 12-volt to 6-volt converter

• Micro “B” USB updatable

FEATURES

• Wire cutter • Crimp tool • Solder gun • Tape

• Connectors (example: butt-connectors, bell caps, etc.)

TOOLS REQUIRED

XSVI-1731-NAV

Honda Data Interface 2016-up

APPLICATIONS

• XSVI-1731-NAV interface • XSVI-1731-NAV harness • AX-CAM6V 12-volt to 6-volt converter

INTERFACE COMPONENTS

HONDA

Civic LX 2016-up

Connections to be made ................................................... 2

Installing the XSVI-1731-NAV .......................................... 3

Initializing the XSVI-1731-NAV ........................................ 3

TABLE OF CONTENTS

XSVI-1731-NAV

Connections to be made

From the XSVI-1731-NAV harness to the aftermarket radio:

•

Connect the wire to chassis ground, and also to the Black wire of the AX-CAM6V.Black

• Connect the Yellow wire to the battery wire.

• Connect the Red wire to the accessory wire.

• If the vehicle is equipped with a factory backup camera:

• Connect the Red wire labeled “6-volt camera” to the AX-CAM6V (sold separately).

• Connect the Yellow RCA jack to the backup camera input.

• If the aftermarket radio has an illumination wire, connect the wire to it.Orange

• Connect the Gray wire to the right front positive speaker output.

• Connect the Gray/Black wire to the right front negative speaker output.

• Connect the White wire to the left front positive speaker output.

• Connect the White/Black wire to the left front negative speaker output.

• Connect the Green wire to the left rear positive speaker output.

• Connect the Green/Black wire to the left rear negative speaker output.

• Connect the Purple wire to the right rear positive speaker output.

• Connect the Purple/Black wire to the right rear negative speaker output.

The following (3) wires are only for multimedia/navigation radios that require

these wires.

• Connect the Blue/Pink wire to the VSS/speed sense wire.

• Connect the Green/Purple wire to the reverse wire.

Note: Before connecting this wire, also refer to the “AX-CAM6V 12-volt to 6-volt”

converter section.

• Connect the Light Green wire to the parking brake wire.

AX-CAM6V 12-volt to 6-volt converter:

• Connect the Blue/Red Red wire to the wire labeled “Camera Power 6V”.

• Connect the Blue/White Green/Purple wire to the wire.

Note: The wire will connect to both the AX-CAM6V, Green/Purple

and the aftermarket radio.

12-pin pre-wired ASWC-1 harness:

• This harness is to be used along with the optional ASWC-1 (not included) to

retain steering wheel audio controls. If the ASWC-1 is not being used, disregard

this harness. If it will be used, please refer to the ASWC-1 instructions for radio

connections and programming.

Note: Disregard the harness that comes with the ASWC-1.

• Connect the Red wire to the accessory wire.

XSVI-1731-NAV

Installing the XSVI-1731-NAV

With the key in the off position:

• Connect the XSVI-1731-NAV harness into the interface, and then to the harness in

the vehicle.

Attention! If the interface loses power for any reason, the following steps will need to be

performed again. Also, if installing an ASWC-1 connect it after you initialize and test the

interface/radio, with the key in the off position.

• Turn the key (or push-to-start button) to the ignition position and wait until the radio

comes on.

Note: If the radio does not come on within 60 seconds, turn the key to the off

position, disconnect the interface, check all connections, reconnect the interface,

and then try again.

• Turn the key to the off position, and then to the accessory position. Test all functions

of the installation for proper operation, before reassembling the dash.

Initializing the XSVI-1731-NAV

Produktspecifikationer

Varumärke:	Metra
Kategori:	Inte kategoriserad
Modell:	Axxess XSVI-1731-NAV

Behöver du hjälp?

Om du behöver hjälp med Metra Axxess XSVI-1731-NAV ställ en fråga nedan och andra användare kommer att svara dig

Ditt namn*

Din e-post*

Skriv din fråga här

Inte kategoriserad Metra Manualer

Metra 71-017C Bruksanvisning

26 September 2024

Metra AXSP-HK Bruksanvisning

26 September 2024

Metra 109-TO7 Bruksanvisning

26 September 2024

Metra 95-8273B Bruksanvisning

26 September 2024

Metra 95-7822 Bruksanvisning

26 September 2024

Metra 82-8703 Bruksanvisning

26 September 2024

Metra 88-00-9004 Bruksanvisning

26 September 2024

Metra 82-9101 Bruksanvisning

26 September 2024

Metra 95-7021HG Bruksanvisning

26 September 2024

Metra 82-5608 Bruksanvisning

26 September 2024

Inte kategoriserad Manualer

Nyaste Inte kategoriserad Manualer

Philips 43PUL7672 Bruksanvisning

27 Oktober 2024

Manhattan 461504 Bruksanvisning

27 Oktober 2024

Sungrow SG125HV Bruksanvisning

27 Oktober 2024

Schneider CCT724319 Bruksanvisning

27 Oktober 2024

Technoline WS 250 Bruksanvisning

27 Oktober 2024

Livarno IAN 354423 Bruksanvisning

27 Oktober 2024

Kupper 12152 Bruksanvisning

27 Oktober 2024

JennAir CARBON24L Bruksanvisning

27 Oktober 2024

Medion Life E74001 (MD 81035) Bruksanvisning

27 Oktober 2024

POLARIS Sportsman Touring 850 SP (2015) Bruksanvisning

27 Oktober 2024