SAB Heli Division Head HPS3 - H0640-K Bruksanvisning

SAB Heli Division Modellbygge Head HPS3 - H0640-K

Läs nedan 📖 manual på svenska för SAB Heli Division Head HPS3 - H0640-K (2 sidor) i kategorin Modellbygge. Denna guide var användbar för 7 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF

Sida 1/2

Approx 45 mm

11mm

Linkage Rod A Assembly . . . .x3

(Initial length for the rods from the

swashplate to the Blade Grip.)

Please read this user manual carefully, it contains instructions for the correct assembly of the KIT.

Please refer to the website www.goblin-helicopter.com for updates and other important information. Thanks You.

Blade Grip Linkage Assembly

Head Cap

Screw M2.5x15mm

(HC028-S)

Flanged Bearing

2.5x

6x2.5

(HC400-S)

Bushing

[H0599]

Blade Grip Linkage

(H0598-S)

Linkage Rod

(H0561-S)

Plastic Ball Link

(H0403-S)

Center Hub Assembly

Center Hub

(H0595-S)

Spindle

(H0596-S)

Uniball M2

(H0538-S)

Uniball M2

(H0538-S)

Uniball M2

(H0537-S)

Swashplate

Assembly

(H0600-S)

Swashplate Assembly

Blade Grip Assembly

Head Cap

Screw M2.5x8mm

(HC020-S)

Bearing

10x4mm

(HC411-S)

Blade Grip Arm

(H0597-S)

Main Blade Grip

(H0513-S)

Washer

7.5x

10x0.5

(H0349-S)

Thrust Bearing

10x4mm

(HC435-S)

Blade Grip Linkage

Assembly

Head Cap Screws

Shoulder M3x16mm

(HC074-S)

Nylon Nut M3

(HC206-S)

Nylon Nut M3

(HC206-S)

Head Cap Screws

Shoulder M3x18

(HC079-S)

Blade Grip

Assembly

C Washer

7x0.2mm

(HC449-S)

[HC449-S]

[H0513-S][H0595-S]

Note

eg: Microlube GL261

HEX 2.5 Inside

Button Head Cap

Screw M4x6mm

(HC096-S)

Bearing

10x4mm

(HC411-S)

A27_Rev 01

Page 1

HPS3 ROTOR HEAD

[

H0640-K

]

Swashplate

[H0600-S]

- 1 x Swashplate Assembly.

- 5 x UniBall M2

4.7H3.

- 1 x UniBall M2

4.7H20.

Radius Arm

[H0421-S]

- 1 x Center Hub.

- 1 x Socket Head Cap Screw Shouldered M3x16mm.

- 1 x Metric Hex Nylon Nut M3.

Center Hub

[H0595-S]

- 2 x Radius Arms.

- 2 x Spacer Arm

5x2.7mm.

- 1 x Spacer Hex.

- 1 x Uniball Radius Arms.

- 2 x Socket Head Cap Screws M3x16mm.

- 2 x Socket Head Cap Screws M2.5x10mm.

- 2 x Flanged Bearings

2.5x

6x2.5mm.

- 4 x Flanged Bearings

7x3mm.

Linkage

[H0598-S]

- 1 x Linkages.

- 1 x

Linkage Rod

- 1 x Bushing.

- 2 x Flanged Bearings

2.5x

6x2.5mm.

Damper Derlin

[H0426-S]

- 3 x H0426-A.

- 3 x H0426-B.

- 3 x H0426-C.

- 3 x Washers

10x

16x1mm.

- 3 x Washers

10x

16x0.2mm.

- 3 x Orings 3050.

Recommendations

- These parts should be used only with models SAB Goblin

- Please follow all the instructions shown in the Goblin main manual. In this manual please read Chapther 2, Important notes

- Use Loctite on all threads.

- Put a small amount of grease inside the hub and the O-Ring.

- Check for axial play of the spindle at least after the first 10 flights and add shims if necessary.

- Firmly tighten the blades before flight.

About HPS

HPS stands for "High Precision System". This head has been

developed in order to increase the usable rotor RPM range without

having to change the rigidity of the dampening system.

The new head is developed specially to limit the teetering effect of

the spindle by means of dampening achieved by a special

technopolymer material.

The maximum teetering amount can be adjusted based on the

amount of play shown in figure "A" of the drawing. The O-ring is

necessary to create a radial and axial preload.

The preload can be kept relatively low, thanks to the mechanical

locking properties of the technopolymer dampeners.

With this solution, finding the correct preload is less complex.

This solution is safer because there is a physical "stop" of the

teetering effect with the technopolymer dampers, also with low

axial preload.

The change of preload will serve exclusively to customize the

response of the model.

Furthermore, the spindle can only move vertically thanks to the

elongated hole shown in section "B" of the drawing.

This solution allows an optimal control of the geometry even when

large amounts of torque are introduced into the system.

The head is very accurate and reliable.

Spare Parts

- 2 x Blade Grip.

- 2 x Thrust Bearing

10x4mm.

- 4 x Bearing

10x4mm.

- 2 x Washer

7.5x

10x0.5mm.

- 2 x Button Head Socket Cap M4x6mm.

- 2 x Washer

7x0.1mm.

Blade Grip

[H0513-S]

- 1 x Blade Grip Arm.

- 1 x Socket Head Cap Screw M2.5.x8mm.

Blade Grip Arm

[H0597-S]

Spindle Shaft

[H0596-S]

- 1 x Spindle Shaft.

- 1 x C Washer

5x0.2mm.

ABOUT HPS3

For safety reasons we suggest to not exceed 3400 rpm.

In addition, we recommend using a smaller tail pulley in order to increase the tail rotor speed to counteract the additional

torque introduced by the 3rd rotor blade. You will find a 20T tail rotor pulley in the kit for this purpose.

TIPS:

Left Side

Right Side

* To remove the dampeners, you

can use a flathead screwdriver

through the hole as shown.

* Clock-wise, counter clock-wise thread

* By turning the linkages you can adjust

tracking. If tracking is adjusted correctly,

you’ll see the metal part line up around

in the center of the opening.

Detail B

SPARE PARTS

RECOMMENDATIONS

These parts should be used only with models SAB Goblin 380.

- 3 blade rotor heads require a much lower cyclic gain on flybarless systems.We recommend that you set your gain at least 30%

lower than the gain you normally use on your 2 blade rotor head helicopters.You can start increasing the gain after you

complete your first flight. Running too high of a gain can induce a violent oscillation that can potentially cause damage

to your helicopter in flight.

- Please follow all the instructions shown in the Goblin main manual.

In this manual please read Chapter 2, Important notes

- Use Loctite on all threads.

Page 2

HPS3 ROTOR HEAD

[

H0640-K

]

Produktspecifikationer

Varumärke:	SAB Heli Division
Kategori:	Modellbygge
Modell:	Head HPS3 - H0640-K
Färg på produkten:	Black, Blue
LED-indikatorer:	Ja
Wi-Fi-standarder:	802.11a, 802.11b, 802.11g, Wi-Fi 4 (802.11n)
Strömförbrukning (i standby):	1 W
Certifiering:	2014/53/EU • LVD 2014/35/EU • EMC 2004/108/WE • RoHS2 2011/65/UE
Material:	Kunststof
Antal per paket:	1 stuk(s)
WiFi-frekvens:	2.4 GHz
Överhettningsskydd:	Ja
Frekvens:	50-60 Hz
Fjärrstyrd:	Ja
Spännande:	110-230 V
Antal kanaler:	2 kanalen
Mått (B x D x H):	39 x 36 x 17 mm
Överbelastningsskydd:	Ja
Maximal räckvidd inomhus:	30 m
Sändningseffekt:	1 mW
Wifi:	Ja
AC-ingångsspänning:	110 - 230 V
AC-ingångsfrekvens:	50 - 60 Hz
Drifttemperatur (TT):	-40 - 40 °C
Antal stolpar:	7
DIN-skena montering:	Nee
Antal moduler:	1
Överföringsräckvidd:	30 - 50 m
Tid för soluppgång/solnedgång:	Ja
Veckoschema:	Ja
Intelligent på/av:	Ja