SAB Heli Division GOBLIN 700 KYLE STACY EDITION Bruksanvisning
SAB Heli Division
Modellbygge
GOBLIN 700 KYLE STACY EDITION
Läs nedan 📖 manual på svenska för SAB Heli Division GOBLIN 700 KYLE STACY EDITION (44 sidor) i kategorin Modellbygge. Denna guide var användbar för 12 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare
Sida 1/44
GOBLIN 700 KYLE STACY EDITION
SAB HELI DIVISIONSAB HELI DIVISION
- Carefully check your model before
each flight to ensure it is airworthy.
- Consider flying only in areas
dedicated to the use of
model helicopters.
- Check and inspect the flying
area to ensure it is clear of
people orbstacles.
- Rotor blades can rotate at very
high speeds! Be aware of the
danger they pose.
- Always keep the model at a
safe distance from other pilots
and spectators.
- Avoid maneuvers with trajectories
towards a crowd.
- Always maintain a safe distance
from the model.
Goblin 700 Kyle Stacy Edition Manual
Release 1.0 - June 2015
WORLD DISTRIBUTION
www.goblin-helicopter.com
For sales inquiries, please email:
sales@goblin-helicopter.com
For info inquiries, please email:
support@goblin-helicopter.com
Attention: If you are a consumer and have questions or need of assistance,
please contact in a first time the Goblin retailer where you made the purchase
EUROPEAN DISTRIBUTION
www.sabitaly.it
For sales inquiries, please email:
sales@sabitaly.it
For info inquiries, please email:
info@sabitaly.it
Attention: If you are a consumer and have questions or need of assistance,
please contact in a first time the Goblin retailer where you made the purchase
375 mm
1388 mm
196 mm
7 – Assembling The Modules
8 – Installation of Swashplate Servos
9 – Installation of The Motor
10 – Installation of The ESC
11 – Installation of Flybarless Unit and RX
12 – Tail Assembly
1 – Serial Number
2 – Important Notes
3 – Components and Box
4 – Carbon frame Assembly
5 – Trasmission Assembly
6 – Main rotor
INDEX
13 – Installation of the Boom, Canopy
14 – Battery
15 – In flight
16 – Maintenance
17 – Exploded Views
18 – Spare Parts
//www.goblin-helicopter.com
http:
Main rotor diameter: 1582mm (with 690mm blades)
Main blade length: 690mm
Tail rotor diameter: 305mm
Tail blade length: 115mm
Main shaft diameter: 12mm
Tail shaft diameter: 6mm
Spindle diameter: 10mm
Weight including standard electronics: 4175g (excluding batteries).
Motor size: Maximum 64mm diameter, maximum height 64mm
Battery compartment: 60x58x350mm (adaptable to 75x58x350mm)
SPECIFICATIONS
It is extremely important that you take a moment to register your helicopter with us. This is the only way to ensure that you are
properly informed about changes to your kit, such as upgrades, retrofits and other important developments. SAB Heli Division
cannot be held responsible for issues arising with your model and will not provide support unless you register your serial number.
To mount the serial number tag on your helicopter, please refer to page 29.
Thank you for your purchase, we hope you enjoy your new Goblin helicopter!
SAB Heli Division
VERY IMPORTANT
Inside Box 5, you will find Bag 21. This bag contains your serial number tag. Please take a moment to register your kit online via our
web site at:
Please read this user manual carefully, it contains instructions for the correct assembly of the model.
Please refer to the web site www.goblin-helicopter.com for updates and other important information.
Page 1
Chapter 1, Serial Number
IMPORTANT NOTES
*This radio controlled helicopter is not a toy.
*This radio controlled helicopter can be very dangerous.
*This radio controlled helicopter is a technically complex device which has to be built and handled very carefully.
*This radio controlled helicopter must be built following these instructions. This manual provides the necessary information
to correctly assemble the model. It is necessary to carefully follow all the instructions.
*Inexperienced pilots must be monitored by expert pilots.
*All operators must wear safety glasses and take appropriate safety precautions.
*A radio controlled helicopter must only be used in open spaces without obstacles, and far enough from people to minimize
the possibility of accidents or of injury to property or persons.
*A radio controlled helicopter can behave in an unexpected manner, causing loss of control of the model, making it very
dangerous.
*Lack of care with assembly or maintenance can result in an unreliable and dangerous model.
*
Neither SAB Heli Division nor its agents have any control over the assembly, maintenance and use of this product.
Therefore, no responsibility can be traced back to the manufacturer. You hereby agree to release SAB Heli Division from
any responsibility or liability arising from the use of this product.
SAFETY GUIDELINES
*Fly only in areas dedicated to the use of model helicopters.
*Follow all control procedures for the radio frequency system.
*It is necessary that you know your radio system well. Check all functions of the transmitter before every flight.
*The blades of the model rotate at a very high speed; be aware of the danger they pose and the damage they may cause.
*Never fly in the vicinity of other people.
NOTES FOR ASSEMBLY
Please refer to this manual for assembly instructions for this model.
Follow the order of assembly indicated. The instructions are divided into chapters, which are structured in a way that
each step is based on the work done in the previous step. Changing the order of assembly may result in additional or
unnecessary steps.
Use thread lockers and retaining compounds as indicated. In general, each bolt or screw that engages with a metal part
requires thread lock.
It is necessary to pay attention to the symbols listed below:
Important
Use retaining
compound
(eg Loctite 648)
Use retaining
compound
(eg Loctite 243)
Use CA Glue
Use Proper
Lubricant
Indicates that for this
assembly phase you need
materials that are in bag xx.
Bag xx
Page 2
Chapter 2, Important Notes
ADDITIONAL COMPONENTS REQUIRED
*Electric Motor: 12S – 480/520Kv
Maximum diameter 64mm,
Maximum height 64mm,
Pinion shaft diameter 6/8mm
*Speed controller: minimum 160A to be safe
*Batteries: 12S - 5000mAh
*1 flybarless 3 axis control unit
*Radio power system, if not integrated with the ESC
*3 cyclic servos
*1 tail rotor servo
*6 channel radio control system on 2.4 GHz
(See configuration examples on page 17)
The assembly process is described in the following chapters.
Each chapter provides you with the box, bag and/or foam
tray numbers you will need for that chapter. The information
is printed in a green box in the upper right hand corner of the
page at the beginning of every chapter.
TOOLS, LUBRICANTS, ADHESIVES
*Generic pliers
*Hexagonal driver, size 1.5,2,2.5,3,4mm
*4mm T-Wrench
*5.5mm Socket wrench (for M3 nuts)
*8mm Hex fork wrench (for M5 nuts)
*Medium threadlocker (eg. Loctite 243)
*Strong retaining compound (eg. Loctite 648)
*Spray lubricant (eg. Try-Flow Oil)
*Synthetic grease (eg. Tri-Flow Synthetic Grease)
*Grease ( eg. Vaseline grease )
*Cyanoacrylate adhesive
*Pitch Gauge (for set-up)
*Soldering equipment (for motor wiring)
Inside the main box:
Box 2: Canopy, Blade Holder.
Box 3: Boom, Blades, Tail blades, Carbon rod.
Box 4: Mechanical parts in 4 trays:
Tray 1: Main rotor
Tray 2: Carbon frame and tail rotor
Tray 3: Transmission
Tray 4: Main structure
Box 5: Bags
Box 6: Carbon parts
Box 7: Landing Gear
Inside the main box there are:
Tray 1
Tray 2
Tray 3
Manual
BOX 6
BOX 7
BOX 2
BOX 4
BOX 5
BOX 3
Page 3
Chapter 3, Components and Box
Flat Head Cap
Screw M2.5x5mm
(HC128-S)
ESC Support
(H0153-S)
Flat Head Cap
Screw M2.5x5mm
(HC128-S)
Flat Head Cap
Screw M2.5x5mm
(HC128-S)
Flat Head Cap Screw
M2.5x5mm
(HC128-S)
Frame Spacer
(H0003-S)
Frame Spacer
(H0003-S)
Frame Spacer
(H0003-S)
Flat Head Cap
Screw M2.5x5mm
(HC128-S)
Battery Tray
(H0002-S)
Stop Battery Plate
(H0150-S)
Socket Head Cap
Screw M2.5x8mm
(HC020-S)
BAG 1.1, FOAM 3, BOX 6
Page 5
Chapter 4, Carbon Frame
Flat Head Cap Screw
M2.5x5mm
(HC128-S)
Frame Spacer
(H0003-S)
Socket Head Cap
Screw M3x10mm
(HC056-S)
Finishing Washer M3
(H0007-S)
ESC Support
Assembly
Main Frame 1
(H0354-S)
Finishing Washer M3
(H0007-S)
Flat Head Cap
Screw M2.5x5mm
(HC128-S)
Frame Spacer
(H0003-S)
ESC Support
(H0088-S)
Cable Pass
(HA010-S)
Canopy Positioners
(H0159-S)
ESC Support
Assembly
ESC Support Assembly
Landing Gear Support
(H0005-S)
Note:
Note:
BAG 1.2, BAG 1.3, FOAM 3
Page 6
Chapter 4, Carbon Frame
Socket Head Cap
Screw M3x10mm
(HC056-S)
Finishing
Washer M3
(H0007-S)
Finishing Washer M3
(H0007-S)
Battery Support
Assembly
Finishing Washer M3
(H0007-S)
Finishing
Washer M3
(H0007-S)
Finishing
Washer M3
(H0007-S)
Main Frame Assembly
Socket Head Cap
Screw M3x10mm
(HC056-S)
Socket Head Cap
Screw M3x10mm
(HC056-S)
Bottom holes: 75mm max height batteries.
Middle holes: 70mm max height batteries.
Canopy
Positioners
(H0159-S)
Top holes: 60mm max height batteries.
Note:
Choose the position for the batteries
For the best 3D performance (with 12S-5000 batteries)
we recommend position 1
Pos 1
BAG 1.2, BOX 6
Page 7
Chapter 4, Carbon Frame
Note:
You can use Super Glue to lock
the nuts in correct position
Metric Hex
Nylon Nut M3
(HC206-S)
Plastic landing gear F3C
(H0449-S)
[HC152-S]
Set Screws M4x4mm
(HC152-S)
Oring
(HC453-S)
Landing Gear Plug
(H0432-S)
Landing Gear ROD
(H0431-S)
Finishing
Washer M3
(H0007-S)
Socket Head Cap
Screws M3x16mm
(HC068-S)
Socket Head Cap
Screws M3x16mm
(HC068-S)
Finishing Washer M3
(H0007-S)
Plastic Landing Gear Assembly
Plastic Landing Gear
Assembly
BAG 2, BOX 7
Page 8
Chapter 4, Carbon Frame
Bearing Support Assembly
(H0024-S)
Bearing
12x
24x6mm
(HC426-S)
Flat Head Cap Screw
M2.5x5mm
(HC128-S)
Socket Head Cap
Screw M3x8mm
(HC050-S)
Socket Head Cap
Screw M3x10mm
(HC056-S)
Column
(H0018-S)
Bearing
10x
19x5mm
(HC422-S)
Note:
Socket Head Cap
Screw M3x10mm
(HC056-S)
Main Structure
(H0009-S)
Antenna Guide
(H0050-S)
Button Head Cap
Screw M3x4mm
(HC038-S)
Swash plate
Anti-Rotation Guide
(H0017-S)
Bearing
12x
24x6mm
(HC426-S)
Finishing Washer M3
(H0007-S)
Column
(H0018-S)
Socket Head Cap
Screw M3x10mm
(HC056-S)
Servo Support
(H0010-S)
Bearing
10x
19x5mm
(HC422-S)
BAG 3, FOAM 1, FOAM 2
Page 9
Chapter 5, Transmission Assembly
One Way Bearing
10x
14x12mm
(HC442-S)
60T Pulley Assembly
(H0171-S)
Bearing
10x
15x4mm
(HC420-S)
Socket Head Cap Screw
Shouldered M2.5x19mm
(HC033-S)
Note 1:
When you tighten the collar (
H0121-S
) on the main
shaft, ensure there is no axial play.
Push down the main shaft while pulling up the
locking collar. Tighten the screw
M4x22
at this time.
Note 2:
The pinion and gear are designed to have zero
backlash. This leads to initial “rough” rotation.
After some run in flights (
3-5 flights
) it will begin to
rotate freely, ensuring perfect contact and the
ability to transmit maximum power.
It is very important to lubricate these two
elements with a lubricant
( Dry Fluids Gear or similar).
One Way Bearing
10x
14x12mm
(HC442-S)
Bearing
10x
15x4mm
(HC420-S)
6.25
4.8
Main Shaft
(H0122-S)
Main Structure
Assembly 1
Socket Head Cap Screw
Shouldered M4x24mm
(HC111-S)
Metric Hex
Nylon Nut M4
(HC212-S)
Metric Hex
Nylon Nut M4
(HC212-S)
Socket Head Cap
Screw M4x22mm
(HC104-S)
Socket Head Cap
Screw Shouldered
M3x18mm
(HC079-S)
60T Pulley
(H0171-S)
60T Pulley Assembly
(H0171-S)
Socket Head Cap
Screw M2x12mm
(HC014-S)
Front Tail Pulley Assembly
(H0172-S)
Bush One Way
(H0110-S)
Note:
Put a small amount of grease
every 30/40 flights on the main
gear (for example Tri- flow
Synthetic grease)
Note 2
The perfect play is 0.5mm
add or remove shim for this
Note:
Correct insertion of
the one-way pulley
37T Pulley
(H0172-S)
Metric Hex
Nylon Nut M3
(HC206-S)
19T Drive Pinion
(H0156-S)
Secondary Shaft
(H0157-S)
M4 Locking Collar
(H0121-S)
Washer
10x
16x0.2mm
(HC232-S)
Metric Hex Nylon
Nut M2.5
(HC200-S)
BAG 4, FOAM 2, FOAM 3
Main Gear
(H0405-S)
Page 10
Chapter 5, Transmission Assembly
Belt Tensioner
Arm
Washer
3x
4x0.5mm
(HC176-S)
Belt Tensioner Support
(H0174-S)
Socket Head Cap
Screw M3x12mm
(HC062-S)
Tail Belt Idler Assembly
(H0174-S)
Belt Tensioner Arm
Assembly
Washer
3.2x
6x0.5mm
(HC180-S)
Socket Head Cap Screw
Shoulder M3x40mm
(HC091-S)
Main Structure
Assembly
Tail Belt Idler
Assembly
Button Head Cap
Screw M3x4mm
(HC038-S)
Belt Tensioner Arm Assembly
(H0174-S)
Note:
Position without preload.
Insert the screw in the
hole through the aluminum
support as in the picture.
Flanged Bearing
3x
7x3mm
(HC402-S)
Tail Belt Idler
[H0069]
Flanged Bearing
5x
9x3mm
(HC410-S)
Spring
de 8 / df0.5 / LL8
(HC315-S)
BAG 5, FOAM 2
Page 11
Chapter 5, Transmission Assembly
Motor Mount
(H0142-S)
Socket Head Cap
Screw M3x10mm
(HC056-S)
Finishing Washer M3
(H0007-S)
Spring
[HC310]
(HC315-S)
Washer
5.3x
15x1mm
(HC188-S)
Metric Hex Nylon
Nut M5
(HC218-S)
34mm
21mm
6mm
0.2mm
7mm
Set Screw
M4x6mm
(HC153-S)
Button Head Cap
Screw M4x8mm
(HC098-S)
20T Pulley
(H0175-20-S)
Lock motor pulley after locking H0142
(see page 17 for optional pulley selection)
Spring
HC314
(HC315-S)
Note for 6mm motor shaft
To maximize space for the batteries, it
is advisable to shorten the motor shaft.
Follow the dimensions given in this
drawing. For the cut, you can use an
electric tool like a “Dremel” with a cut-
off disc.
Additionally, ensure the motor shaft
has an appropriate 'flat' for one of the
set screws.
Socket Head Cap
Screw M3x8mm
(HC050-S)
Bearing Support (H0143-S)
Lock H0142 after have locked
the motor.Motor shaft is requires
to optimize the centering. H0142
can't be used with motor shaft 8mm.
Bushing
6x
8x18mm
(H0176-S)
Use with 6mm
motor shaft.
Flanged Bearing
6x
13x5mm
(HC414-S)
Socket Head Cap
Screw M3x10mm
(HC056-S)
Set Screw M5x20mm
(HC158-S)
Motor Support
(H0143-S)
Motor
BAG 6, FOAM 1, FOAM 2
Page 12
Chapter 5, Transmission Assembly
Finishing
Washer M3
(H0007-S)
Socket Head Cap
Screw M3x8mm
(HC050-S)
Socket Head Cap
Screw M3x12mm
(HC062-S)
Carbon Frame
Assembly
Canopy Mount
Base
(H0319-S)
Head HPS3
Assembly
Central Group
Assembly
Socket Head Cap
Screw M3x8mm
(HC050-S)
Metric Hex
Nylon Nut M4
(HC212-S)
Socket Head Cap
Shoudered M4x24mm
(HC111-S)
Finishing
Washer M3
(H0007-S)
Swashplate
Assembly
Flat Head Cap
Screw M3x8mm
(HC134-S)
BAG 8, FOAM 3
Canopy Mount
Base
(H0319-S)
Flat Head Cap
Screw M3x8mm
(HC134-S)
Page 14
Chapter 7, Assembling The Modules
ASSEMBLY OF THE BALL ON THE HORN.
The rods going from the servos to the swash plate must be as
vertical as possible. Not all servos are equal, so to better align
them you can choose to use the supplied spacer H0031.
Figure 4 illustrates this.
INSTALLATION OF SWASHPLATE SERVOS
The linkage ball must be positioned between
17-19 mm
out on the servo arm (
figure 1
), recommended servo arm SAB
p/n [HA050/HA051]. The 120° placement of the servos inside Goblin means the arms are difficult to access. For this reason it is
advisable to ensure alignment of the servo arms (and sub trim set) before installation of the servos in the model (
figure 2
).
Proceed with installation following the instructions below.
Figure 3
shows a completed installation.
Uniball M2
5H6
(H0064-S)
Socket Head Cap Screw M2x8mm
(HC008-S)
or
Socket Head Cap Screw M2x6mm
(HC004-S) without Uniball Spacer
Servo 2
SERVO ASSEMBLY 1, 2, 3
Servo 1
Uniball Spacer
[H0031]
(H0064-S)
Socket Head Cap
Screw M2.5x12mm
(HC026-S)
Socket Head Cap Screw
M3x6mm
(HC044-S)
Socket Head Cap
Screw M2.5x8mm
(HC020-S)
Servo 1
Servo 3
Servo Spacer
(H0075-S)
Servo 2
Servo 3
17-19mm
Servo 1
BAG 9
Page 15
Chapter 8, Installation Of Swashplate Servos
Note: Although the Goblin can fly at high rpm, for safety reasons we suggest to not exceed 2000 rpm.
Some example configurations:
TRANSMISSION SETUP
It is important to choose the right reduction ratio to maximize efficiency based on your required
flight performance.
The Goblin has many possible reduction ratios at your disposal. It is possible to optimize any motor
and battery combination.
It is recommended to use wiring and connectors appropriate for the currents generated in a
helicopter of this class.
If you are using a head speed calculator which requires a main gear and pinion tooth count, use
214
teeth for the main gear (this takes into account the two stage reduction) and the tooth count of your
pulley as the pinion count.
Below is a list of available reduction ratios
:
H0175-18-S - 18T Pinion = ratio 11.9:1 H0175-22-S - 22T Pinion = ratio 9.8:1
H0175-19-S - 19T Pinion = ratio 11.3:1 H0175-23-S - 23T Pinion = ratio 9.3:1
H0175-20-S - 20T Pinion = ratio 10.7:1 H0175-24-S - 24T Pinion = ratio 8.9:1
H0175-21-S - 21T Pinion = ratio 10.2:1 H0175-25-S - 25T Pinion = ratio 8.6:1
GOBLIN 700 KYLE STACY EDITION CONFIGURATIONS
GOBLIN 700 KYLE STACY EDITION CONFIGURATIONS
Rev:01
Battery
Motor
ESC
Pinion
RPM
Max (Gov)
Pitch
3D CONFIGURATION
12S
5000/5500 mAh
Kontrionik Pyro 800-480
Edge 160 HV
21T
1800/1900 rpm
± 12,5
YGE 160 HV
KOSMIK 160/200
20T
± 12,5
Xnova 4530-500KV
KDE 700 G3 HP 505
Edge 160 HV
20T
± 12,5
YGE 160 HV
KOSMIK 160/200
19T
± 12,5
Scorpion HK-4525-520
Edge 160 HV
19T
± 12,5
YGE 160 HV
KOSMIK 160/200
18T
± 12,5
HARD 3D CONFIGURATION
12S
5000/5500 mAh
Kontrionik Pyro 800-480
COMPETITION
XNOVA XTS 4530-480
Edge 160 HV
22T
1900/2000 rpm
± 12,5
YGE 160 HV
KOSMIK 160/200
21T
± 12,5
Scorpion HK-4530-500
KDE 700 G3 HP 505
Edge 160 HV
21T
± 12,5
YGE 160 HV
KOSMIK 160/200
20T
± 12,5
Page 17
Chapter 9, Installation Of The Motor
Fig 1:
Figure 1 shows the motor correctly
wired. It is advisable to cover the wire
joints between the motor and the ESC
with heat shrink tubing.
2 mm
0.75 mm 0.75 mm
Big Motor Belt
(HC309-S)
MOTOR BELT TENSION
*Assemble the motor and pinion to its mounting plate.
*Fit the motor assembly into position.
*Compress the springs by pushing the motor toward the main shaft.
*At maximum compression, temporarily tighten one of the slide screws.
*With the minimum centre distance it is easy to install the belt. First put the belt on the motor pinion.
*Then put the belt around the big pulley.
*Rotate the motor several times by hand.
*Release the screw that locks the slide.
*The springs keep the belt in tension.
*Help the springs by pulling the motor slightly.
*The belt must be very tight.
*Lock all screws.
Motor Assembly
Note:
Check for vertical alignment of
the motor pulley. To do this, simply
turn the motor several time and
check to you see if the belt is aligned
with the big pulley ( one way bearing
pulley ). If the belt is riding too high,
simply loosen up the motor pulley
and drop it just a little bit, if it is
riding too low, loosen up the motor
pulley and raise it a bit.
Correct
Incorrect
FOAM 2
Page 18
Chapter 9, Installation Of The Motor
FLYBARLESS CONTROL UNIT AND RX INSTALLATION
It is possible to install any commercially available Flybarless control unit in the goblin.
For Flybarless systems with a separate sensor, the sensor must be installed under the plate (
Figure 1
).
Figure 2
shows an example of installation of the receiver and flybarless control unit.
In
Figure 3
you can see the extension lead for the tail servo. It is very important to include a connector for fast
disassembly of the boom module. The connector will prevent servo damage in case of boom separation during a crash.
Slot for
sensor cable
It is important to lock the plugs of the
flybarless unit with an adhesive - for
example hot glue.
Tail servo extension cable
To install a one piece Flybarless system it is necessary to add the support shown in these figures.
Figure 3 shows the installed support. Figure 4 shows the control unit and the receiver installed on the support.
Support
Flybarless
(H0043-S)
Spacer Support
Flybarless
(H0043-S)
RX
Flate Head Cap
Screw M3x8mm
(HC134-S)
Socket Head Cap
Screw M3x6mm
(HC044-S)
Flybarless Unit
Socket Head Cap
Screw M3x6mm
(HC044-S)
Double-sided
Tape
BAG 18
Page 20
Chapter 11, Installation Of Flybarless Unit and RX
Block Nut
(H0358-S)
Flat Head Cap
Screws M3x8mm
(HC134-S)
Linkage Tail
Support
(H0045-S)
Set Screw
M3x20mm
(HC150-S)
Yellow Carbon
Tail Boom (H9045-S)
Locking Element
Tail Assembly
Locking Element Tail Assembly .... X 2
Boom Spacer
(H0082-S)
Note:
Metric Hex Nylon Nut M3
(HC206-S)
DETAIL A
DETAIL C
Tail Boom Assembly
Locking Element Tail
(H0041-S)
Attaching H0082-S to the boom:
Pre-assemble the two boom spacers H0082-S with
the M3x20 socket set screw.
Insert into the boom tube completely done up.
Center the holes, then unscrew until there is contact with the walls
Lock everything with the adhesive.
Assemble H0040-S in the boom:
Before assembling the two parts in the boom we suggest tightening the
M2.5 screws into the two plastic parts to pre-thread them. In this way
when you will assemble the tail servo it will be easier to tighten the screws
into the plastic parts. Check the tail servo can fit, if necessary carefully sand
the hole.
Assemble H0045-S in the boom:
Before mounting H0045 on the boom we
suggest to first tighten the M2.5 screws into the
holes to thread them. In this way when you
assemble the part it will be easier to tighten the
screws.
Socket Head Cap
Screw M2.5x6mm
(HC018-S)
Tail Servo Lock
(H0040-S)
Double
Sided Tape
A
B
C
DETAIL B
BAG 14
Page 23
Chapter 12, Tail
A
DETAIL A
SCALE 1 : 1.5
Socket Head Cap
Screw M3x12mm
(HC062-S)
Finishing Washer M3
(H0007-S)
3mm 3mm
Approx 754mm
13mm13mm
Finishing
Washer M3
(H0007-S)
Socket Head Cap
Screw M3x12mm
(HC062-S)
Tail Boom
Assembly
Plastic Ball Link
(H0066-S)
Carbon Rod
4x
2.5x702mm
(HC239-S)
Threaded Rod M2.5x40mm
(HC242-S)
Note:
Note: Before put plastic ball in threaded rod, please wait 12 hours after bonding
Plastic Ball Link
(H0066-S)
Threaded Rod M2.5x40mm
(HC242-S)
BAG 13, BAG 16, BOX 3
Page 24
Chapter 12, Tail
0.75 mm
BOOM ASSEMBLY
*Insert the tail boom assembly .
*Lock the M8 nuts with the HA016 special tool supplied.
*Firmly lock the lateral srews M3x12mm. Use Loctile for this screw and make sure you remain tight.
*Assemble the H0038 carbon security plate .
*Connect the tail servo wire to the previously fitted extension lead.
Nylon Screw
M8x20mm
(HC165-S)
Note:
Between the boom and the aluminum plate,
there is a space of around 0.75mm.
Look the picture.
Socket Head Cap
Screw M3x6mm
(HC044-S)
Finishing Washer
(H0007-S)
Socket Head Cap
Screw M3x12mm
(HC062-S)
Washer
3.1x
12x18mm
(H0078-S)
Socket Head Cap
Screw M3x12mm
(HC062-S)
Safety Locking
Tail Boom
(H0038-S)
BAG 17
Page 26
Chapter 13, Installation Of The Boom
CANOPY
Install the canopy following these step :
- Canopy grommets (Fig 6), Canopy edge protection (Fig 7), Adhesive foam tape.
The canopy hole must be 12.5 mm in diameter. Initially is 9 mm.
You can enlarge the hole slightly to optimize the vertical position of the canopy itself.
To install the canopy:
- Insert the canopy from the front up to the area of the block shown in Fig. 8.
- Use Canopy quick release for the correctly locked Fig. 9.
It is recommended a bit of lubricant on the quick release canopy mount system.
VERY IMPORTANT
Always ensure the proper installation and locking before each flight. The lock button must always come out to ensure locking.
It is recommended to attempt removal by forcing the canopy slightly to ensure proper locking.
TAIL BELT TENSION
*Check the proper assembly of the tail boom.
*Check that the aluminum part of the tube is against the M3 stop screw.
*Loosen the tail group by loosening the 4 M3 screws.
*Install the belt onto the pulley, taking care to respect the direction of rotation (
figure 1
).
*Rotate the tail drive several times by hand.
*Load the spring by a rotation of
270°
the tensioning arm (
clockwise
).
*Tension the boom until the tensioning arm is aligned with the frame.
*Tighten the 4 screws.
*Check that the tail output shaft is perpendicular to the tube. (
figure 2
)
*In
figure 3,4,5
you can see the three conditions, ok, too loose and too tight.
NOTE
. To disassemble the tail boom it is possible to remove the pulley H0172-S without loosening the tail unit.
Remove the locking screw and pull down.
FOAM 3
Page 27
Chapter 13, Installation Of The Boom, Canopy
A
B
Battery Plate
(H0149-S)
Cylinder M2.5
(H0151-S)
Flat Head Cap
Screw M2.5x5mm
(HC128-S)
BATTERIES
The battery tray system in the Goblin 700 is simple, but very effective.
The battery should be attached to the tray (Part
H0149
) with heat shrink, tape or velcro.
You can optionally use the battery protection tray (Part
H0151
) see
Fig. 1, 2
.
Before permanently mounting the batteries onto the battery tray, check the ideal position
for the best center of gravity.
Cut the heat shrink around the carbon fiber tray locking pins. Fig. 3.
Battery Pack:
Slide the tray until it locks into the CNC stopper.
Fig. 4, 5
.
Using the velcro straps, making sure that the two locking pins are stopped against the frame spacer
(Part1#
H0003
and #
H0151
)
Fig.6, 7
.
BAG 19
Note:
Using sandpaper, sand
the slot where you insert the
battery strap. This helps
increase the life of the strap.
Page 28
Chapter 14, Battery
OPERATIONS BEFORE FLIGHT
*Set up the remote control and the flybarless system with utmost care.
*It is advisable to test the correct settings of the remote and flybarless system without main blades or tail blades fitted.
*Check that all wiring is isolated from the carbon/aluminum parts. It is good practice to protect them at the points where
they are at most risk.
*Be sure of the gear ratio, verifying carefully the motor pulley in use. The forces acting on the mechanics increase
enormously with increasing of rpm. Although the Goblin can fly at high rpm, for safety reasons we suggest to not exceed
2000 rpm.
*Check the correct tension of the tail belt through the belt tensioner.
*Fit the main blades and tail blades. (Fig.1 and Fig.2)
*Please make sure the main blades are tight on the blade grips, you should be able to violently jerk the head in both
directions and the blades should not fold. Failure to tighten the blades properly can result in a boom strike.
To fold the blades for storage, it is advisable to loosen them.
*Check the collective and cyclic pitch. For 3D flight, set about +/- 12°-13°.
*It is important to check the correct tracking of the main blades.
*On the Goblin, in order to correct the tracking, adjust the main link rod as shown in figure 3.
This is provided with a right/left thread system that allows continuous fine adjustments of the length of the control rod;
for this adjustment it is not necessary to detach the ball link.
*Perform the first flight at a low headspeed, 1500/1600 RPM.
After this first flight, do a general check of the helicopter. Verify that all screws are correctly tightened.
SERIAL NUMBER
In Bag 21, you will find the serial
number tag for your Helicopter
Sticking the tag as show.
Please remember to register
your product. (See page 1)
Always in Bag 21, you can take the KSE
plate and put in this position
IN FLIGHT
During its first flights the Goblin has to be “run in”.
The Damper, the main gear, the uniball and other parts must undergo some slight wear to operate smoothly. It is likely that
during the very first flights the model may exhibit a swaying phenomena, particularly at low head speed.
This phenomena disappears after a few flights.
If you want to fly in a generic way, using both low headspeed (1600rpm) and higher headspeed (1900rpm),
the standard setting is the best compromise (3BW5115 with 25T tail pulley).
However, if you want the best setup for high RPM (2000 rpm) we recommend changing the tail blades from 3BW5115 to
3BW5104 and tail pulley from 25T to 24T (H0154-S).
With high RPM, the smaller tail blades will work well creating less drag in very fast maneuvers, for the best performance!
Socket Head Cap
Screw M5x35mm
(HC116-S)
(HC218-S)
Socket Head Cap Screw
Special M3x18mm
(HC079-S)
(HC206-S)
(H0158-S)
BAG 20B, BAG 21
Page 29
Chapter 15, In Flight
MAINTENANCE
*On the Goblin, areas to look for wear include:
* Motor belt
* Tail belt
* Damper
* Main gear and pinion
The lifespan of these components varies according to the type of flying. On average it is recommended to replace
these special parts every
100
flights.
*The head tends to lose rigidity after a while. Check this condition every
20
flights. Preloading with precision shim washers,
it is possible to vary the rigidity of the head.
*Check all uniballs often.
*The most stressed bearings are definitely those of the tail shaft. Check them frequently.
All other parts are not particularly subject to wear.
*Periodically lubricate the tail slide movement and its linkages as well as the swashplate movement and its linkages.
*Lubricate the main gear with silicone and Tri-Flow Synthetic grease, even though the gear is made of technopolymer,
a high mineral based filler, it still requires some lubrication.
*Check the screws that are highlighted in the following images frequently, make sure you remain tight (
fig.2
and
fig.3
).
*To ensure safety you should do a general inspection of the helicopter after each flight. You should check:
* The maintenance of proper belt tension.
* The proper isolation of wires from the carbon and aluminum parts.
* That all screws remain tight.
ABOUT HPS3
The new HPS head offers an independent dampening system for
each blade grip, there are three dampening settings:
A = Soft for smooth response.
B = Medium.
C = Firm for direct and precise response.
In the kit, there is the damper for
direct and precise responce H0426-C
Other Setting >> p/n H0426-S
ABOUT HPS3 SETUP
3 blade rotor heads require a much lower cyclic gain on flybarless systems.
We recommend that you set your gain at least 30% lower than the gain
you normally use on your 2 blade rotor head helicopters.
You can start increasing the gain after you complete your first flight.
Running too high of a gain can induce a violent oscillation that can
potentially cause damage to your helicopter in flight.
With 3 blades rotor head, it is very important to have a perfect tracking
Often, unusual vibration are determined by wrong tracking.
Note:
To remove the dampeners,
you can use a flathead
screwdriver through the
hole as shown.
Page 30
Chapter 16, Maintenance
3
4
11
12
12
10
16
17
19
21
21
22
1
2
2
2
3
3
3
3
3
5
6
8
18
19 21
21
21
21
21
21
9
3
7
14
19
23
23
25
3
13
15
20
24
19
19
Main Frame
POS
COD
Name
Specification
Quantity
1
H0002
Battery Tray Carbon Fiber
1
2
H0003
Frame Spacers
Aluminum
5
3
H0007
Finishing Washers M3
Aluminum
12
4
H0088
ESC Support
Carbon Fiber
1
5
H0149
Battery Plate
Carbon Fiber
1
6
H0150
Stop Battery Plate
Aluminum
1
7
H0151
Cylinder M2.5
Aluminum
2
8
H0153
Battery Support
Carbon Fiber
1
9
H0155
Battery Protection
Carbon Fiber
1
10
H0159
Canopy Positioner
Plastics
2
11
H0319
Canopy Mouse Base
Steel
2
12
H0354
Main Frames
Carbon Fiber
2
13
H0431
Landing Gears Rod
Aluminum
2
Main Frame
POS
COD
Name
Specification
Quantity
14
H0432
Landing Gears Plug
Plastic
4
15
H0449
Plastic Landing Gear F3C
Plastic
2
16
H0319
Quick Realise Canopy
Assembly
2
17
HA010
Cable Pass
16 x
24 x 2mm
1
18
HC020
Socket Head Cap Screws
M2.5 x 8mm
2
19
HC056
Socket Head Cap Screws
M3 x 10mm
12
20
HC068
Socket Head Cap Screws
M3 x 16mm
4
21
HC128
Flat Head Cap Screws
M2.5 x 5mm
16
22
HC134
Flat Head Cap Screws
M3 x 8mm
2
23
HC152
Set Screw
M4 x 4mm
4
24
HC206
Nylon Nuts
M3
4
25
HC453 Oring
Plastic
4
Page 31
Chapter 17, Exploded view, Carbon Frame
1
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
18
19
20
21
22
23
24
17
25
26
27
27
28
27
1
1
28
29
29
29
29
29
30
31
32
33
34
35
36
37
38
39
40
4142
26
43
44
45
46
46
47
48
49
50
51
52
53
55
55
56
56
57
57
58
58
54
59
1
TRANSMISSION ASSEMBLY
POS
COD
Name
Specification
Quantity
31
HC079
Socket Head Cap Screws
M3 x 18mm
1
32
HC091
Socket Head Cap Shoudered
M4 x 40mm
1
33
HC098
Button Head Cap Screws
M4 x 8mm
4
34
HC104
Socket Head Cap Screw
M4 x 22mm
1
35
HC111
Socket Head Cap Screw
M4 x 24mm
1
36
HC128
Flat Head Cap Screws
M2.5 x 5mm
3
37
HC134
Flat Head Cap Screw
M3 x 8mm
1
38
HC153
Set Screws
M4 x 6mm
1
39
HC158
Set Screws
M5 x 20mm
2
40
HC165
Vite Nylon Esa
M8 x 20mm
2
41
HC176
Washer
3 x
4x0.5mm
1
42
HC180
Washers
3.2 x
6 x 0.5mm
2
43
HC188
Washers
5.3 x
15 x 1mm
2
44
HC200
Metric Hex Nylon Nuts
M2.5 H3.5mm
2
45
HC206
Metric Hex Nylon Nuts
M3 H4mm
1
46
HC212
Metric Hex Nylon Nuts
M4 H5mm
2
47
HC218
Metric Hex Nylon Nuts
M5 H4.8mm
2
48
HC309
Big Motor Belt
240-3MGT
1
49
HC310
Spring
de 5.8-df0.3-ll9
2
50
HC312
Spring
de 8-df0.5-ll8
1
51
HC314
Spring
de 8-df0.5-ll12
2
52
HC402
Flanged Bearings
3 x
7 x 3mm
2
53
HC410
Flanged Bearings
5 x
9 x 3mm
2
54
HC414
Flanged Bearings
6 x
13 x 5mm
1
55
HC420
Bearings
10 x
15 x 4mm
2
56
HC422
Bearings
10 x
19 x 5mm
2
57
HC426
Bearings
12 x
24 x 6mm
2
58
HC442
One Way Bearing
10 x
14 x 12mm
2
59
HC232
Washer
10 x
16 x 0.2mm
1
TRANSMISSION ASSEMBLY
POS
COD
Name
Specification
Quantity
1
H0007
Finishing Washers M3
Aluminum
4
2
H0009
Main Structure
Aluminum
1
3
H0010
Servo Support
Aluminum
1
4
H0017
Swash plate Anti-Rotation Guide
Carbon Fiber
1
5
H0018
Columns
Aluminum
4
6
H0024
Main Shaft Bearing Support
1
7
H0038
Safety Locking Tail Boom
Carbon Fiber
1
8
H0043
Spacers Flybarless
3
9
H0050
Antenna Guide
Plastic
2
10
H0069
Tail Belt Idler
1
11
H0071
Belt Tensioner Arm
1
12
H0077
Flybarless Support
Carbon Fiber
1
13
H0110
Bush-One Ways
10 x
13 x 1.4mm
2
14
H0121
M4 Locking Collar
1
15
H0122
Main Shaft
1
16
H0142
Support Bearing
Aluminum
1
17
H0156
Steel Pinion
19T
1
18
H0157
Secondary Shaft
1
19
H0171
One Way Double Bearing
60T
1
20
H0172
Front Tail Pulley Low
37T
1
21
H0174
Column Belt Tensioner
1
22
H0175-20
Motor Pulley 20mm
20t 1
23
H0143
Motor Support
Aluminum
1
24
H0405
Main Gear CNC
68T M1
1
25
HC033
Socket Head Cap Screw Shouldereds
M2.5 x 19mm
1
26
HC038
Button Head Cap Screws
M3 x 4mm
3
27
HC044
Socket Head Cap Screws
M3 x 6mm
5
28
HC050
Socket Head Cap Screws
M3 x 8mm
3
29
HC056
Socket Head Cap Screws
M3 x 10mm
7
30
HC062
Socket Head Cap Screw
M3 x 12mm
1
TRANSMISSION ASSEMBLY
POS
COD
Name
Specification
Quantity
Page 32
Chapter 17, Exploded view, Transmission Assembly
1
3
6
26
4
5
7
8
910
12
13
14
15
16
22
23
11
17
24
27
28
28
30
31
32
33
34
36
38
40
41
42
43
44
44
45
45
Head System
Head System
4
4
4
2
18
19
20
21
26
28
29
35
25
37
39
46
47
42
49
48
Servo Assembly 1, 2, 3
Swashplate Set - H0420
1
POS
COD
Name
Specification
Quantity
26
HC008
Head Cap Screws
M2 x 8mm
6
27
HC018
Head Cap Screws
M2.5x6mm
6
28
HC020
Head Cap Screws
M2.5x10mm
5
29
HC026
Head Cap Screws
M2.5x12mm
9
30
HC056
Head Cap Screws
M3x10mm
1
31
HC068
Head Cap Screws
M3x16mm
2
32
HC102
Head Cap Screws
M4x10mm
3
33
HC111
Head Cap Shoulder
M4x24mm
1
34
HC116
Head Cap Shoulder
M5x35mm
3
35
HC124
Head Cap Screws
M6x10mm
3
36
HC140
Threaded Rods
M2.5 x 18mm
3
37
HC170
Washers
2 x
5 x 0.5mm
3
38
HC176
Washers
3x
4x0.5
2
39
HC194
Washers
6x
14x1
3
40
HC212
Metric Hex Nylon Nut
M4 H5
1
41
HC218
Metric Hex Nylon Nut
M5
3
42
HC230
Washers
10x
16x1
6
43
HC232
Washers
10x
16x0.2
3
44
HC400
Flanged Bearing
2.5x
6x2.5
2
45
HC402
Flanged Bearing
3x
7x3
4
46
HC422
Bearing
10x
19x5
6
47
HC430
Bearing Rads
30 x
37 x 4mm
2
48
HC438
Thrust Bearing
10x
18x5.5
3
49
HC062
Head Cap Screws
M3x12mm
1
POS
COD
Name
Specification
Quantity
1
H0031
Uniball Spacers
Aluminum
3
2
H0063
Uniballs
M3x4
5 H18
1
3
H0064
Uniballs
M2.5
5 H6
3
4
H0065
Uniball M3
Steel
3
5
H0066
Plastic Ball Linkages
Plastic
8
6
H0075
Servo Spacers
Carbon Fiber
6
7
H0134
Spacer Arm
Aluminum
2
8
H0158
Blade Washers
Aluminum
6
9
H0182BL
Main Blade Grip
Aluminum
3
10
H0183BL
Blade Grip Arm
Aluminum
3
11
H0402
Ball Linkages
Plastic
6
12
H0410BL
Center Hub
Aluminum
1
13
H0412
Spindle
Steel
3
14
H0413
Pin 5mm
Aluminum
3
15
H0415
Uniball Radius Arm
Plastic
1
16
H0416
Spacer Arm
Aluminum
1
17
H0417
Linkage Rod
Aluminum
3
18
H0420-01BL
Swashplate 01
Aluminum
1
19
H0420-02BL
Swashplate 02
Aluminum
1
20
H0420-03
Swashplate 03
Steel
1
21
H0420-04BL
Swashplate 04
Aluminum
1
22
H0421
Radius Arm
Aluminum
2
23
H0426
Damper derlin
Pom black
3
24
HA024
Oring
3
25
HC002
Head Cap Screws
M2x5mm
3
Page 33
Chapter 17, Exploded view, Head System
1
2
3
4
4
5
6
9
10
11
12
12
13
13
14
15
8
16
17
20
21
23
24
7
26
27
28
29
18
19
25
30
31
32
32
33
33
34
34
35
36
37
37
37
38
36
39
41
42
45
46
46
47
36
36
48
48
49
50
50
41
44
51
51
52
52
53
53
22
40 43
54
55
56
TAIL SYSTEM
POS
COD
Name
Specification
Quantity
1
H0007
Finishing Washer M3
Aluminum
4
2
H0029
Spacer
8.1 x
9.2 x 3.2mm
1
3
H0040
Tail Servo Locks
Plastic
2
4
H0041
Locking Element Tails
Carbon Fiber
2
5
H0045
Linkage Tail Support
Plastic
1
6
H0046
Yellow Vertical Fin
Carbon fiber
1
H0117
Red Vertical Fin
Carbon fiber
1
7
H0054
Tail Pitch Slider 02
Aluminum
1
8
H0056
Tail Pitch Slider Link
Aluminum
3
9H0058BL
Bell Crank Base
Aluminum
1
10
H0060
Spacer
3 x
4 x 9.6mm
1
11 H0061BL
Tail Case Spacers
Aluminum
2
12
H0064
Uniballs
M2.5
5H6
2
13
H0066
plastic ball links
Plastic
2
14
H0075
Servo Spacer
Carbon Fiber
2
15
H0076
Spacer
2x
2x3mm
3
16
H0078
Washers
3.1 x
12 x 1.8mm
2
17
H0082
Boom spacers
Aluminum
2
18
H0155
Tail Pulley
25T
1
19
H0264
Pin M3
2
20 H0327BL
Tail Blade Grip
Aluminum
3
21
H0349
Spacer
7.5x
10x0.5mm
3
22
H0358
Block Nut
Aluminum
1
23
H0359
Tail Side Plate
Aluminum
1
24
H0360
Tail Upper Case
Aluminum
1
25 H0406BL
Tail Bell Crank
Aluminum
1
26
H0407
Tail Pitch Slider 02
Plastic
1
27 H0409BL
Tail Pitch Slider 01
Aluminum
1
28
H0418
Tail Hub
Steel
1
TAIL SYSTEM
POS
COD
Name
Specification
Quantity
29
H0419
Tail Shaft
Steel
1
30
H0435
Bushing
Aluminum
3
31
H9045
Carbon Tail Boom
1
32
HC004
Socket Head Cap Screws
M2 x 6mm
6
33
HC008
Socket Head Cap Screws
M2 x 8mm
2
34
HC020
Socket Head Cap Screws
M2.5 x 8mm
4
35
HC026
Socket Head Cap Screws
M2.5 x 12mm
4
36
HC050
Socket Head Cap Screws
M3 x 8mm
11
37
HC062
Socket Head Cap Screws
M3 x 12mm
6
38
HC079
Socket Head Cap Screws Shoulder M3 x 18mm
2
39
HC086
Socket Head Cap Screws
M3 x 22mm
1
40
HC134
Flat Head Cap Screws
M3x8mm
1
41
HC150
Set Screws
M3 x 20mm
1
42
HC153
Set Screws
M4 x 6mm
2
43
HC165
N
ylon Screw
2
44
HC176
Washer
3x
4x0.5mm
1
45
HC181
Washer
3x
7x1mm
3
46
HC206
Metric Hex Nylon Nuts
M3
7
47
HC239 Carbon Rod
2.5 x
4 x 702mm
1
48
HC242
Threaded Rods
M2.5 x 40mm
2
49
HC304
Belt Gates
2061-3gt-06
1
50
HC402
Flanged Bearings
3 x
7 x 3mm
2
51
HC411
Bearings
5x
10x4mm
6
52
HC414
Flanged Bearings
6 x
13 x 5mm
2
53
HC418
Flanged Bearings
8 x
12 x 3.5mm
2
54
HC435
Thrust Bearings
5x
10x4mm
2
55
HC449
Washer
5x
7x0.2
3
56
HA015
Double-Sided Tapes
2
Page 34
Chapter 17, Exploded view, Tail System
Battery Tray
[H0002-S]
Frame Spacer
[H0003-S]
- 3 x Frame Spacers.
- 10 x Finishing Washers M3.
Finishing Washer M3
[H0007-S]
Main Structure
[H0009-S]
Servo Support
[H0010-S]
- 1 x CF Swashplate
Anti-Rotation Guide.
- 1 x Finishing Washer M3.
- 1 x Socket Head Cap Screw
M3x8mm.
Swashplate Anti-Rotation Guide
[H0017-S]
Chapter 18, Spare Parts
Column
[H0018-S]
- 4 x Columns.
- 1 x Bearing Support.
- 1 x Bearing
12x
24x6mm.
- 3 x Flat Head Cap Screws
M2.5x5mm.
Bearing Support
[H0024-S]
- 1 x Safety Lock Tail Boom.
- 1 x Finishing Washer M3.
- 1 x Socket Head Cap Screw
M3x8mm.
Safety Lock Tail Boom
[H0038-S]
- 2 x Tail Servo Locks.
- 2 x Servo Spacers.
- 4 x Socket Head Cap Screws
M2.5x12mm.
Tail Servo Lock
[H0040-S]
- 2 x Locking Element Tails.
- 4 x Metric Hex Nylon Nuts M3.
- 2 x Double Sided Tapes.
Locking Element Tail
[H0041-S]
Spacer Flybarless
[H0043-S]
- 3 x Spacer Flybarless.
- 1 x Supporto Flybarless.
- 1 x Flat Head Cap Screw M3x8mm.
- 5 x Socket Head Cap Screws
M3x6mm.
- 1 x Linkage Tail Support.
- 2 x Socket Head Cap
Screws M2.5x6mm.
Linkage Tail Support
[H0045-S]
Yellow Vertical Fin
[H0046-S]
- 1 x Yellow Vertical Fin.
- 2 x Socket Head Cap Screws
M3x12mm.
- 2 x Finishing Washers M3.
- 2 x Antenna Guide.
- 2 x Button Head Cap
Screws M3x4mm.
Antenna Guide
[H0050-S]
Aluminum Bell Crank Base
(H0058BL-S)
- 1 x Main Structure.
- 1 x Aluminum Bell Crank Base.
Tail Case Spacer
[H0061BL-S]
- 2 x Tail Case Spacers.
- 4 x Socket Head Cap
Screws M3x8mm.
Uniball M3x4 5H18
[H0063-S]
- 2 x Uniball M3x4 5H18.
Uniball M2 5H6
[H0064-S]
- 5 x Uniballs M2 5H6.
- 5 x Uniball Spacers.
- 5 x Socket Head Cap
Screws M2x8mm.
- 5 x Socket Head Cap
Screws M2x6mm.
Uniball M3x4 5H3
[H0065-S]
- 5 x Uniballs M3x4 5H3.5.
- 1 x CF Battery Tray.
- 6 x Flat Head Cap Screws
M2.5x5mm.
- 1 x Servo Support.
Page 35
- 1 x Red Vertical Fin.
- 2 x Socket Head Cap
Screws M3x12mm.
- 2 x Finishing Washers M3.
Red Vertical Fin
[H0117-S]
- 4 x Washers
3.1x
12x1.8mm.
Washer
3.1x
12x1.8mm
[H0078-S]
Servo Spacer
[H0075-S]
- 1 x 25T Tail Pulley.
- 1 x Set Screw M4x4mm.
- 6 x Socket Head Cap Screws
M2x5mm.
25T Tail Pulley
[H0155-S]
Plastic Ball Link
[H0066-S]
- 10 x Servo Spacers.
- 10 x Plastic Ball Link.
Boom Spacer
[H0082-S]
- 2 x Boom Spacer.
- 1 x
Set Screw M3x20mm.
- 1 x ESC Support.
- 2 x Frame Spacer.
- 4 x Flat Head Cap Screws
M2.5x5mm.
ESC Support
[H0088-S]
Bush One Way
[H0110-S]
- 4 x Bush One Ways.
M4 Locking Collar
[H0121-S]
- 1 x M4 Locking Collar.
- 1 x Socket Head Cap Screw
M4x22mm.
- 1 x Metric Hex Nylon Nut M4 H5.
- 1 x Main Shaft.
- 1 x M4 Locking Collar
- 1 x Socket Head Cap Screw
Shouldered M4x24mm.
- 2 x Socket Head Cap
Screws M4x22mm.
- 3 x Metric Hex Nylon Nuts M4.
Main Shaft
[H0122-S]
Bearing Support
[H0143-S]
- 1 x Bearing Support.
- 1 x Flanged Bearing
6x
13x5mm.
- 2 x Socket Head Cap
Screws M3x8mm.
Battery Tray
[H0149-S]
- 1 x Battery Plate.
- 1 x Battery Protection.
- 2 x Cylinder M2.5.
- 2 x Flat Head Cap
Screw M2.5x5mm
- 1 x Heat Shrink.
Stop Battery Tray
[H0150-S]
- 1 x Stop Battery Tray.
- 2 x Socket Head Cap
Screw M2.5x8mm.
Carbon Fiber ESC Support
(H0153-S)
- 1 x Carbon Fiber ESC Support.
- 6 x Flat Head Socket Cap
Screw M2,5x5mm.
19T Drive Pinion
[H0156-S]
- 1 x 19T Drive Pinion.
- 1 x Socket Head Cap Screw
Shouldered M3x19mm.
- 1 x Metric Hex Nylon Nut M3.
Secondary Shaft
[H0157-S]
- 1 x Secondary Shaft M3.
- 1 x Socket Head Cap Screw
Shoulder M2.5x19mm.
- 1 x Metric Hex Nylon Nut M2,5.
- 1 x Socket Head Cap
Shoulder M3x19mm.
- 1 x Metric Hex locknut Nut M3.
Aluminum Blade Spacer
[H0158-S]
- 4 x Aluminum Blade Spacer.
Canopy Positioner
[H0159-S]
- 2 x Canopy Positioner.
- 2 x Socket Head Cap
Screws M3x10mm.
Double Bearing One Way Pulley
[H0171-S]
- 1 x Aluminum Double Bearing
One Way Pulley Assembly.
- 3 x Shims
10x
16x0,2mm.
- 1 x One Way Brass Bushing.
Aluminum Front Tail Pulley
[H0172-S]
- 1 x Front Tail Pulley Assembly.
- 1 x Socket Head Cap
Screw M2.5x19mm.
- 1 x Metric Hex Nylon Nuts M2,5.
Page 36
Chapter 18, Spare Parts
- 1 x Column Belt Tensioner.
- 1 x Tail Belt Idler.
- 1 x Belt Tensioner Arm.
- 2 x Flanged Bearings
3x
7x3mm.
- 2 x Flanged Bearings
5x
9x3mm.
- 1 x Socket Head Cap
Screw M3x50mm.
- 1 x Washer
3x
4x0.5mm.
- 1 x Socket Head Cap
Screw M3x12mm.
- 2 x Washers
3.2x
6x0.5mm.
- 1 x Button Head Cap
Screw M3x4mm.
- 1 x Spring De8/df0.5/LL8.
Belt Tensioner Support
[H0174-S]
- 1 x 18T Pulley.
- 1 x Set Screws M4x4mm.
- 1 x 19T Pulley.
- 1 x Set Screws M4x4mm.
19T Pulley
[H0175-19-S]
18T Pulley
[H0175-18-S]
- 1 x 21T Pulley.
- 1 x Set Screws M4x4mm.
- 1 x 20T Pulley.
- 1 x Set Screws M4x4mm.
20T Pulley
[H0175-20-S]
21T Pulley
[H0175-21-S]
- 1 x 22T Pulley.
- 1 x Set Screws M4x4mm.
- 1 x 23T Pulley.
- 1 x Set Screws M4x4mm.
23T Pulley
[H0175-23-S]
22T Pulley
[H0175-22-S]
- 1 x 24T Pulley.
- 1 x Set Screws M4x4mm.
24T Pulley
[H0175-24-S]
Blade Grip
[H0182BL-S]
- 2 x Blade Grip.
- 2 x
Thrust Bearing
10x
18x5.5.
- 4 x Bearing
10x
19x5mm.
- 2 x Washer
10x
16x1mm.
Blade Grip Arm
[H0183BL-S]
- 2 x Blade Grip Arm.
- 2 x Socket Head Cap
Screw M4x10mm.
- 2 x Uniball M3x4 Ø5 H3.5.
Motor Mount
[H0142-S]
- 1 x Bearing
Support.
- 1 x Motor Mount.
- 1 x Flanged Bearing
6x
13x5mm.
- 2 x Socket Head Cap Screws M3x8.
- 2 x Set Screws M5x20mm.
- 2 x Washers
5.3x
15x1mm.
- 2 x Metric Hex Nylon Nuts M5H4.8.
- 2 x Finishing Washers M3.
- 2 x Socket Head Cap Screws M3x10.
- 2 x Metric Hex Nylon Nut M3 H4.
- 2 x Springs de 5.8/ df0.5 / LL9.
- 2 x Springs de 3/ df0.5 / LL12.
Quick Release Canopy Mount
[H0319-S]
- 2 x Quick Release Canopy Set.
- 2 x Flat Head Socket Cap M3x8.
- 2 x Canopy Grommets.
CNC Derlin Main Gear
[H0405-S]
- 1 x CNC Derlin Main Gear Set.
Aluminum Tail Blade Grip
[H0327BL-S]
- 2 x Aluminum Tail Blade Grip.
- 4 x Bearing Ø5xØ10x4mm.
- 2 x Thrust bearing Ø5xØ10x4mm.
- 2 x Button Head Cap M4x8mm.
- 2 x Socket Head Cap M2x6mm.
- 2 x Washer Ø5xØ8.9x0,75mm.
- 2 x Washer Ø7.5xØ10x0,5mm.
Main Frame
[H0354-S]
- 1 x Main Frame.
Tail Boom Support
[H0358-S]
- 1 x Tail Boom Support.
- 1 x Nylon screw M8x20mm.
- 1 x Flat Head Cap ScrewsM3x8.
Aluminum Tail Side Plate
[H0359-S]
- 1 x Aluminum Tail Side Plate.
- 1 x Flanged bearing
Ø6xØ13x5mm.
Aluminum Tail Case Spacer
[H0360-S]
- 1 x Aluminum Tail Case Spacer.
- 4 x Socket Head Cap M3x8mm.
Ball Link
[H0402-S]
- 5 x Ball Link.
Page 37
Chapter 18, Spare Parts
Produktspecifikationer
| Varumärke: | SAB Heli Division |
| Kategori: | Modellbygge |
| Modell: | GOBLIN 700 KYLE STACY EDITION |
Behöver du hjälp?
Om du behöver hjälp med SAB Heli Division GOBLIN 700 KYLE STACY EDITION ställ en fråga nedan och andra användare kommer att svara dig
Modellbygge SAB Heli Division Manualer
12 September 2024
11 September 2024
SAB Heli Division GOBLIN 700 KYLE STACY EDITION Bruksanvisning
11 September 2024
11 September 2024
10 September 2024
SAB Heli Division Head HPS3 - H0490-K Goblin 570 Bruksanvisning
10 September 2024
10 September 2024
SAB Heli Division Goblin 570 KYLE STACY EDITION Bruksanvisning
10 September 2024
10 September 2024
Modellbygge Manualer
- Modellbygge Lego
- Modellbygge Chicco
- Modellbygge Carson
- Modellbygge Voltcraft
- Modellbygge Viessmann
- Modellbygge Revell
- Modellbygge Playmobil
- Modellbygge BRIO
- Modellbygge Graupner
- Modellbygge ISDT
- Modellbygge Heller
- Modellbygge Multiplex
- Modellbygge Wilesco
- Modellbygge FABER CASTELL
- Modellbygge Marklin
- Modellbygge Kibri
- Modellbygge Mega Bloks
- Modellbygge KidKraft
- Modellbygge Geomag
- Modellbygge Thames & Kosmos
- Modellbygge Baufix
- Modellbygge Reely
- Modellbygge Robbe
- Modellbygge LGB
- Modellbygge Woodland Scenics
- Modellbygge Snap Circuits
- Modellbygge BIG
- Modellbygge Discovery
- Modellbygge Quercetti
- Modellbygge Pocher
- Modellbygge Wiking
- Modellbygge Siku
- Modellbygge MBZ
- Modellbygge FALLER
- Modellbygge Seuthe
- Modellbygge Metal Earth
- Modellbygge E-Blox
- Modellbygge Piko
- Modellbygge Fleischmann
- Modellbygge Tams Elektronik
- Modellbygge Roco
- Modellbygge Proses
- Modellbygge Brawa
- Modellbygge NOCH
- Modellbygge Massoth
- Modellbygge Trix
- Modellbygge Italeri
Nyaste Modellbygge Manualer
2 April 2025
2 April 2025
2 April 2025
29 Mars 2025
24 Mars 2025
24 Mars 2025
4 Mars 2025
24 Februari 2025
23 Februari 2025