Tripp Lite SmartOnline Bruksanvisning

Tripp Lite UPS SmartOnline

Läs nedan 📖 manual på svenska för Tripp Lite SmartOnline (16 sidor) i kategorin UPS. Denna guide var användbar för 2 personer och betygsatt med 4.5 stjärnor i genomsnitt av 2 användare

Ladda ner PDF

Sida 1/16

Owner’s Manual

1111 W. 35th Street Chicago, IL 60609 USA

Customer Support: (773) 869-1234 • www.tripplite.com

Important Safety Instructions 2

Installation 3

Basic Operation 6

Battery Replacement 12

Storage and Service 14

SmartOnline™

Rack/Tower Mount Online UPS Systems

Specifications 14

Español

Français 31

™ is a trademark of Tripp Lite.

Troubleshooting 10

PyccŞèé 46

UPS Location Warnings

• Install your UPS indoors, away from excess moisture or heat, conductive contaminants,

dust or direct sunlight.

• For best performance, keep the indoor temperature between between 32º F and 104º F

(0º C and 40º C).

• Leave adequate space around all sides of the UPS for proper ventilation.

UPS Connection Warnings

• Connect your UPS directly to a properly grounded AC power outlet. Do not plug the

UPS into itself; this will damage the UPS.

• Do not modify the UPS's plug, and do not use an adapter that would eliminate the UPS’s

ground connection.

• Do not use extension cords to connect the UPS to an AC outlet. Your warranty will be

voided if anything other than Tripp Lite surge suppressors are used to connect your UPS

to an outlet.

• If the UPS receives power from a motor-powered AC generator, the generator must

provide clean, filtered, computer-grade output.

Equipment Connection Warnings

• Do not use Tripp Lite UPS Systems for life support applications in which a malfunction

or failure of a Tripp Lite UPS System could cause failure or significantly alter the

performance of a life-support device.

• Do not connect surge suppressors or extension cords to the output of your UPS. This

might damage the UPS and will void the surge suppressor and UPS warranties.

Battery Warnings

• Your UPS does not require routine maintenance. Do not open your UPS for any reason

except battery replacement. There are no user-serviceable parts inside.

• Battery replacement must be performed by qualified service personnel. Because the

batteries present a risk of electrical shock and burn from high short-circuit current,

observe proper precautions. Unplug and turn off the UPS before performing battery

replacement. Use tools with insulated handles, and replace the existing batteries with the

same number and type of new batteries (Sealed Lead-Acid). Do not open the batteries.

Do not short or bridge the battery terminals with any object.

• The UPS batteries are recyclable. Refer to local codes for disposal requirements, or in

the USA only call 1-800-SAV-LEAD for recycling information. Do not dispose of the

batteries in a fire.

• Only connect Tripp Lite battery packs of the appropriate type and correct voltage to the

external battery connector.

• Do not connect or disconnect external batteries while the UPS is operating from battery.

• Do not operate your UPS without batteries.

SAVE THESE INSTRUCTIONS

This manual contains instructions and warnings that should be followed during the

installation, operation and storage of all Tripp Lite UPS Systems. Failure to heed these

warnings will void your warranty.

Important Safety Instructions

Rackmount

1) Loosen the wingnuts on each of the two UPS

Side Supports; adjust the length of the supports to

match the depth of your rack; tighten wingnuts.

2) Mount both UPS Side Supports in your rack on

the inside surfaces of the rack rails.

Note: Both support ledges should face inward. The side supports’

front and back holes are threaded and do not require nuts to

secure rack bolts.

3) Attach mounting ‘ears’ to the front end of the

UPS’s sides using the screws provided.

4) Lift UPS and slide it onto the UPS Side

Supports within your rack. Mount the UPS by

screwing rack bolts through the UPS mounting

‘ears’, through the rack rails and through the UPS

Side Supports.

Note: The side supports’ front holes are threaded and do not

require nuts to secure rack bolts.

Vertical Tower Mount

1) Cover the rackmount screw holes on the UPS’s

sides with supplied snap-in hole-cover caps.

2) Place the UPS upright in a flat, stable location

with its control panel on the high corner facing

forward. Position stabilizer feet 4 in. from each

end of the UPS.

Mounting

SU2200RTXL2U shown

Installation

Produktspecifikationer

Varumärke:	Tripp Lite
Kategori:	UPS
Modell:	SmartOnline
Typ av operation:	Touch
Färg på produkten:	Wit
Inbyggd display:	Ja
Vikt:	3550 g
Bredd:	620 mm
Djup:	230 mm
Höjd:	430 mm
Snäll:	Convector elektrisch verwarmingstoestel
Tillgångar:	2000 W
Beeldscherm:	LED
Lämplig för:	Binnen
Antal per paket:	1 stuk(s)
Överhettningsskydd:	Ja
AC-ingångsspänning:	220 - 240 V
AC-ingångsfrekvens:	50 - 60 Hz
Lämplig för rumsvolymer upp till:	60 m³
Timerlängd (max):	9 uur
Värmekraft:	2000 W
Placeringsalternativ:	Vloer
Typ av värmeelement:	Aluminium
Värmeeffekt (min):	1250 W